BEGA 24 221 Wall Luminaire Instruction Manual

: June 12, 2024
: BEGA

Table of Contents

Dimension
Instructions For Use
- Application
Safety
Overvoltage Protection
Installation
Cleaning · Maintenance
Replacing the LED module
Spares
Customer Support
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BEGA 24 221 Wall Luminaire

Dimension

Instructions For Use

Application

Wall luminaire with asymmetrical light distribution.
For lighting of floor spaces, traffic areas and house entrances.

Product description
Luminaire made of aluminium alloy, aluminium and stainless steel
BEGA Unidure® coating technology
Safety glass with optical structure Silicone gasket
Reflector made of pure anodised aluminium 2 mounting holes ø 5mm
Distance apart 240mm 2 cable entries for through-wiring of mains
supply cable ø 7-10.5mm
Connecting terminal and earth conductor terminal 2.5@
LED power supply unit
220-240 V ∼ 0/50-60 Hz
DC 170-276 V
BEGA Thermal Switch®
Temporary thermal shutdown to protect temperature-sensitive components
Safety class I
Protection class IP 65
Dust-tight and protection against water jets
Impact strength IK09
Protection against mechanical impacts < 10 joule
Safety mark
Conformity mark
Weight: 3.8 kg
This product contains light sources of energy efficiency classes B, C

Safety

The installation and operation of this luminaire are subject to national safety regulations.
Installation and commissioning may only be carried out by a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or installation.
If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Overvoltage Protection

The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e.g. transients, etc. we recommend separate overvoltage protection components.
You can find them on our website at www.bega.com.

Lamp
Module connected wattage 13.4 W
Luminaire connected wattage 15.8 W
Rated temperature ta=25 °C
Ambient temperature ta max=45 °C

24 221K3
Module designation LED-0731/830
Colour temperature 3000 K
Colour rendering index CRI >80
Module luminous flux 2650 lm
Luminaire luminous flux 1466 lm
Luminaire luminous efficiency 92,8 lm/W

24 221K4
Module designation LED-0731/840
Colour temperature 4000 K
Colour rendering index CRI >80
Module luminous flux 2725 lm
Luminaire luminous flux 1507 lm
Luminaire luminous efficiency 95,4 lm/W

Installation

LED are high-quality electronic components! Please avoid touching the light output opening of the LED directly during installation or relamping.

In outdoor areas, the light emission may only be directed downwards.
Undo the screws and lift off the luminaire top.
Lead the mains supply cable through the cable entry of the luminaire base.
Note position of application of the luminaire “arrow down”.
Fix luminaire base with enclosed or any other suitable fixing material onto the mounting surface.
Be sure to use the gasket rings supplied.
Make the earth conductor connection and the electrical connection.

In order to guarantee the maximum service life of the electrical components, the enclosed desiccant pouch must be placed in the luminaire.
Remove the desiccant pouch from the foil packaging and place it in the position marked by the red information label immediately before finally closing the luminaire.

Make sure that gasket is positioned correctly.
Make earth conductor connection between luminaire top and luminaire base.
Replace the luminaire top and tighten the screws evenly.

Cleaning · Maintenance

Clean luminaire regularly with solvent-free cleansers from dirt and deposits.
Do not use high pressure cleaners.

Replacing the LED module

The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted.
The module can be replaced by qualified persons using standard tools.
Disconnect the system and open the luminaire.
Please follow the installation instructions for the LED module.
Inspect and, if necessary, replace the luminaire gaskets.
Defective glass must be replaced.
Close the luminaire.