BEGA 89 760.1 Ceiling and Wall Luminaires Instruction Manual
- June 12, 2024
- BEGA
Table of Contents
BEGA 89 760.1 Ceiling and Wall Luminaires
Product Information
- Product Name: 89 760.1
- IP Rating: IP 44
- Power Consumption: 7 W
- Colour Temperature: 2700 K / 3000 K
- Luminous Flux: 805 lm
- Dimmable: Yes
- Includes BEGA LED Lamp: Yes
- LED Lamp Model Numbers: 13548 (2700 K), 13586 (3000 K)
Product Usage Instructions
-
Safety:
– The installation and operation of this luminaire should comply with national safety regulations.
– Installation and commissioning should only be carried out by a qualified electrician.
– The manufacturer is not liable for damage caused by improper use or installation.
– Any modifications to the luminaire should be done by the person responsible for them, who will be considered the manufacturer. -
Sliding-Bolt Closure:
– To securely hold the glass, place it on the base plate and ensure that the holding springbolts fit into the notches of the glass.
– Rotate the glass clockwise to lock it in place for safe and vibration- resistant holding.
– To release the glass from the base plate, turn it counter-clockwise. -
Spares:
– If you need replacement parts, the following are available:
– Spare Glass
– LED Lamp 2700 K
– LED Lamp 3000 K
– Lampholder
– Reflector
– Model Numbers: 11 002 772 .0R G, 13 548, 13 586, 63 000 355, 76 000 835
Detailed technical and lighting data for the lamps can be found in the data sheets on our website.
Dimension
Ceiling and wall luminaire for indoor use
Application
Ceiling and wall luminaire · indoor luminaire made of hand-blown opal glass, satin matt and metal housing, for all lighting tasks. They are ideal for places where a soft and uniform lighting distribution is required. Luminaire with a high protection class.
Lamp
Luminaire with lampholder E 27
Lamp output max. 3 × 60 W
This product contains light sources of energy efficiency classes E, F
89 760.1 K2
inclusive BEGA LED lamp 13548
dimmable
LED 7 W 805 lm
Colour temperature 2700 K
89 760.1 K3
inclusive BEGA LED lamp 13586
dimmable
LED 7 W 805 lm
Colour temperature 3000 K
Detailed technical and lighting data for the lamps can be found in the data sheets on our website.
Product description
- Metal housing, finish Colour white
- Hand-blown opal glass, satin matt, with sliding-bolt closure
- 2 mounting holes ø 5.5 mm
- Distance apart 280 mm
- 2 cable entries for through-wiring for mains cable up to ø 10.5 mm max. 3 × 1.5@
- Connection terminal 2.5@
- Earth conductor connection
- Lampholder E 27
- Safety class I
- Protection class IP 44
- Protected against granular foreign bodies
- ≥ 1 mm and splash water
- – Safety mark
- – Conformity mark
- Weight: 4.4 kg
Safety
The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician. The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.
Installation
- Pass the mains supply cable through the mounting plate.
- Notice position of application »arrow down« when installed at the wall.
- Fix base of the luminaire with enclosed or any other suitable fixing material on to the mounting surface.
- It is imperative to use the enclosed gaskets.
- Make earth conductor connection.
- Push silicone sleeves over the lines and make electrical connection.
- Insert lamp.
- Insert the opal glass into the luminaire base with sliding bolt glass closure and turn the glass clockwise up to the stop.
The sliding-bolt closure
- The sliding-bolt closure provides a safe and vibration-resistant holding of glass.
- Place glass to the base plate and observe that the holding springbolts fit into the notches of the glass.
- Turn the glass clockwise until it is locked. Thus, you reach a safe and vibration-resistant holding of the glass.
- To release the glass from the base plate, turn it counter-clockwise.
Relamping · Maintenance
- Disconnect from main supply.
- Remove glass turning it counter-clockwise.
- Clean glass.
- Use only solvent-free cleansers.
- Change the lamp.
- Place glass into fitter and turn it clockwise until the stop.
Spares
- Spare glass 11 002 772 .0R G
- LED lamp 2700 K 13 548
- LED lamp 3000 K 13 586
- Lampholder 63 000 355
- Reflector 76 000 835
BEGA Gantenbrink-Leuchten KG · Postfach 31 60 · 58689 Menden · info@bega.com · www.bega.com