BEGA 50133 Indoor Wall Luminaire Instruction Manual

: June 12, 2024
: BEGA

Table of Contents

BEGA 50133 Indoor Wall Luminaire
Product Information
Product Usage Instructions
Instructions for use
Product description
Safety Precautions
Additional Information
Installation
Cleaning · Maintenance
Spare Parts
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BEGA 50133 Indoor Wall Luminaire

Product Information

Product Description: Aluminium fitter, finish Colour white
Dimensions: 180 x 240 mm spacing
Weight: 1.8 kg
Energy Efficiency Class: F
Lamp Type: LED-1246/930
Colour Temperature: 3000 K
Colour Rendering Index (CRI): Ra > 90
Luminous Flux: 2640 lm
Luminous Efficiency: 80.4 lm/W

Product Usage Instructions

Ensure that the installation and operation of this luminaire comply with national safety regulations.
Installation and commissioning should be carried out by a qualified electrician.
Do not modify the luminaire without proper authorization.
To protect against overvoltage and transients, consider using separate overvoltage protection components.
Clean the luminaire using suitable cleansers to remove dirt.
If the glass is defective, it should be replaced.
If the LED module needs replacement, use the LED module with a colour temperature of 3000 K (part number: LED-1246/930).

Instructions for use

Application
Open and free-radiating wall luminaire · indoor luminaire with hand-blown opal glass and metal bracket. The character of the opal glass creates a smooth and uniform light distribution in the room.

Product description

Aluminium fitter, finish Colour white
Stainless steel glass holding bolts
Hand-blown opal glass
3 fixing holes ø 6.5 mm
180 x 240 mm spacing
2 cable entries for through-wiring for mains cable up to ø 10.5 mm max. 3 × 1.5@ Connection terminal 2.5@
Earth conductor connection
LED module for power supply
Suitable for phase angle or phase section dimming
220-230 V y 50/60 Hz
BEGA Thermal Switch®
Temporary thermal shutdown to protect temperature-sensitive components
Safety class I
– Safety mark
– Conformity mark
Weight: 1.8 kg
This product contains light sources of energy efficiency class(es) F

Safety Precautions

Always follow the national safety regulations when installing and operating this luminaire. Improper use or installation may result in damage, and the manufacturer does not accept liability for such damage. If modifications are made to the luminaire, the person responsible for the modifications will be considered the manufacturer. The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician. The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Additional Information

The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547. For additional protection against transients, etc., it is recommended to use separate overvoltage protection components. These components can be found on the manufacturer’s website at www.bega.com.

Lamp

Luminaire connected wattage: 28 W
Rated temperature: ta = 25 °C
Ambient temperature: ta max = 25 °C

50 133 K3

Module designation: 2x LED-1246/930 3000 K
Colour temperature: Ra > 90
Colour rendering index: 2640 lm
Module luminous flux: 2252 lm
Luminaire luminous flux: 80,4 lm / W
Luminaire luminous efficiency

Installation

LED are high-quality electronic components! Please avoid touching the light output opening of the LED directly during installation or relamping. Lead the mains supply cable through the cable entry of the luminaire base.Fix luminaire base with enclosed or any other suitable fixing material onto the mounting surface. Notice position of use “arrow down” of the luminaire base. Make earth conductor connection. Push silicone sleeves over the lines and make electrical connection. Mount glass to luminaire base with the glass holding bolts.

Cleaning · Maintenance

Clean luminaire regularly with solvent-free cleansers from dirt. Defective glass must be replaced.

Replacement of the LED module
The designation of the LED module is noted on a label in the luminaire. The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted. The module can be replaced by a qualified electrician or a comparably qualified person using standard tools. Disconnect the system. Remove glass by unscrewing glass holding bolts. Please follow the installation instructions for the LED module. Defective glass must be replaced. Mount glass to luminaire base with the glass holding bolts.