BEGA 50595.1 LED Wall Luminaire Instruction Manual
- June 12, 2024
- BEGA
Table of Contents
BEGA 50595.1 LED Wall Luminaire
Product Information
- Product Description: Mundgeblasenes Opalglas
- Distance: 320 mm Anschlussklemme
- Schutzleiteranschluss: 2,5@
- Digital Control: L2E20D–2N4e0tzVtex il 0/50-60 Hz DC 176-264
- DALI Controllable: Yes
- Safety: The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician. The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.
- Overvoltage Protection: The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547.
- To achieve additional protection against e.g. transients, etc. we recommend separate overvoltage protection components. You can find them on our website at www.bega.com.
- Lamp Module Connected Wattage: 12,2 W
- Luminaire Connected Wattage: 14,6 W
- Rated Temperature: ta max = 25°C
- Ambient Temperature: ta = 50°C
- Module Designation: 2x LED-0627/930
- Color Temperature: 3000 K
- Colour Rendering Index (CRI): CRI > 90
- Module Luminous Flux: 2020 lm
- Luminaire Luminous Flux: 1465 lm
- Luminaire Luminous Efficiency: 100,3 lm / W
Product Usage Instructions
- Mounting: Only fix the luminaire in the position of the application as pictured. For relamping, mounting, and dismantling of the glass, please keep a distance of 400 mm above the luminaire.
- Cleaning: Clean the luminaire regularly with solvent-free cleansers to remove dirt.
- LED Module Replacement: The designation of the LED module is noted on a label in the luminaire. The light color and light output of BEGA replacement modules correspond to those of the modules originally fitted. The module can be replaced by qualified persons using standard tools. Disconnect the system and open the luminaire.
- Please follow the installation instructions for the LED module. The defective glass must be replaced. Close the luminaire.
Wall luminaire for indoor use
Instructions for use
Application
Open and free-radiating wall luminaire · indoor luminaire with hand-blown opal glass and metal housing. The character of the opal glass creates a smooth and uniform light distribution in the room.
Product Description
- Metal luminaire housing, finish Colour white
- Hand-blown opal glass
- 2 mounting holes ø 6.5 mm
- Distance apart 320 mm
- Connection terminal 2.5
- Earth conductor connection
- 2-pole connecting terminal for
- digital control
- LED power supply unit
- 220-240 V x 0/50-60 Hz
- DC 176-264 V
DALI-controllable
Basic insulation is provided between the mains and control cables
- Safety class I
- r – Safety mark
- c – Conformity mark
- Weight: 1.6 kg
This product contains light sources of energy efficiency class(es) D
Safety
The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician. The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.
Overvoltage protection
The electronic components installed in the luminaire are protected against
overvoltage in accordance with DIN EN 61547. To achieve additional protection
against e. g. transients, etc. we recommend separate overvoltage protection
components.
You can find them on our website at www.bega.com.
Lamp
- Module connected wattage 12.2 W
- Luminaire connected wattage 14.6 W
- Rated temperature ta = 25 °C
- Ambient temperature ta max = 50 °C 50 595.1 K3
- Module designation 2x LED-0627/930
- Color temperature 3000 K
- Color rendering index CRI > 90
- Module luminous flux 2020 lm
- Luminaire luminous flux 1465 lm
- Luminaire luminous efficiency 100,3 lm / W
Please note
If the luminaire is to be mounted onto a metallic, electroconductive surface,
it is mandatory to make sure that the mounting surface is connected
conductively to the earth conductor of the luminaire!
Installation
Only fix the luminaire in the position of application as pictured. For
relamping, mounting, and dismantling of the glass please keep a distance of
400 mm above the luminaire. LED are high-quality electronic components! Please
avoid touching the light output opening of the LED directly during
installation or relamping. Slide the synthetic diffuser out of the LED
supporting section. Make the earth conductor connection and the electrical
connection to the terminals. For digital control please use the connecting
terminal DA, DA. In case this terminal is not used the luminaire will be
operated at full light output. Fix the luminaire housing with enclosed or any
other suitable fixing material onto the mounting surface. Make sure to use the
gaskets supplied. Note the position of the application “arrow down”. Insert
the synthetic diffuser by sliding it into the LED supporting section until the
stop. Loosen the knurled knob. Position glass into luminaire housing and fix
it
with the knurled knob.
Cleaning · Maintenance
Clean the luminaire regularly with solvent-free cleansers from dirt.
Replacement of the LED module
The designation of the LED module is noted on a label in the luminaire. The light color and light output of BEGA replacement modules correspond to those of the modules originally fitted. The module can be replaced by qualified persons using standard tools. Disconnect the system and open the luminaire. Please follow the installation instructions for the LED module. The defective glass must be replaced. Close the luminaire.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>