BEGA 34067.1 Ceiling and Wall Luminaire Instruction Manual

: June 12, 2024
: BEGA

Table of Contents

BEGA 34067.1 Ceiling and Wall Luminaire
Product Information:
Product Usage Instructions
Ceiling and wall luminaire for indoor use
Instructions for use
Installation
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BEGA 34067.1 Ceiling and Wall Luminaire

BEGA-34067.1-Ceiling-and-Wall-Luminaire-PRODUCT-IMAGE

Product Information:

The product is a luminaire with the following specifications:

Lamp Module connected wattage: 103.2 W
Luminaire connected wattage: 115 W
Rated temperature: ta = 25-45°C
Ambient temperature: ta = 25-45°C
Module designation: 34 067.1 K3
Color temperature: 3000 K
Color rendering index (CRI): CRI > 90
Module luminous flux: 18320 lm
Luminaire luminous flux: 10814 lm
Luminaire luminous efficiency: 94 lm/W

Product Usage Instructions

Safety: The installation and operation of this luminaire must comply with national safety regulations. Only a qualified electrician should perform the installation and commissioning. The manufacturer is not liable for any damage caused by improper use or installation. If any modifications are made to the luminaire, the person responsible for these modifications will be considered the manufacturer.
Overvoltage Protection: The electronic components in the luminaire are protected against overvoltage according to DIN EN 61547. For additional protection against transients, it is recommended to use separate overvoltage protection components, which can be found on the manufacturer’s website at www.bega.com.
Prior to Installation:
- Ensure that the ceiling or wall has sufficient load capacity to support the luminaire.
- Consider the position of the cable entries for the electrical connection (refer to the provided sketch).
- Drill 6 mounting points in the mounting surface. Note that general fixing material may not be suitable for all applications. Check the approval of building supervision.
Installation:
- Remove the luminaire from its packaging and place it on a soft surface.
- To open the luminaire, use a hex key (size 3) to turn the ceiling bracket on the housing ring a quarter turn to the left.
- Fully open the ceiling bracket by slightly tilting the torsion spring back.
- Carefully raise the installation box and disconnect the LED connectors on the left and right sides.
- Using a socket wrench or a ratchet, unscrew the 3 nuts above the hinge until the end of the thread.
- Pull the safety clamp forward and remove the installation box upwards.
- When installing on a wall, ensure that the application arrow is pointing down and that the safety clamp is facing upwards.
- Fix the installation box onto the mounting surface using the provided or suitable fixing material.
- Lead the mains supply cable through one of the 4 cable entries into the installation box.
- Make an earth connection and an electrical connection to the terminals.
- If digital control is desired, use the connecting terminal DA, DA. If this terminal is not used, the luminaire will operate at full light output.
- Pick up the luminaire and insert the hinge laterally to the arrester.
- Tightly screw the three hex nuts above the hinge with a torque of 3.4 Nm. Note that the luminaire is securely attached to the ceiling bracket only when all three nuts are tightened.

Ceiling and wall luminaire for indoor use

BEGA-34067.1-Ceiling-and-Wall-Luminaire-01

Instructions for use

Application
Large-area luminaire · indoor luminaire with high light power and high uniform light distribution.

Product description

Luminaire housing made of aluminum
Finish color white
Crystal glass, inside white
Silicone gasket
4 cable entries for through-wiring for mains cable up to ø 11 mm max. 5 x 1.5@ Connection terminal 2.5@
Earth conductor connection 2-pole connecting terminal for digital control
LED power supply unit
220-240 V x 0/50-60 Hz
DC 176-276 V
During DC operation the LED power is reduced to 15 %
DALI-controllable
Basic insulation is provided between the mains and control cables
BEGA Thermal Control®
Temporary thermal regulation to protect temperature-sensitive components without switching off the luminaire
Safety class I
– Safety mark
CE – Conformity mark
Weight: 22.4 kg

This product contains light sources of energy efficiency class(es) C

Lamp

Module connected wattage 103.2 W
Luminaire connected wattage 115 W
Rated temperature ta = 25 °C
Ambient temperature ta max = 45 °C

34 067.1 K3

Module designation 8x LED-0845/930
Color temperature 3000 K
Color rendering index CRI > 90
Module luminous flux 18320 lm
Luminaire luminous flux 10814 lm
Luminaire luminous efficiency 94 lm / W

Safety
The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to
the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Overvoltage protection
The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e. g. transients, etc. we recommend separate overvoltage protection components.
You can find them on our website at www.bega.com.

Notice prior to installation:
For fixing the luminaire please consider sufficient load capacity of ceiling or wall.
For the electrical connection the position of the cable entries must be considered (see sketch). Drill 6 mounting points in the mounting surface. General fixing material may not be suitable for all applications.
Note approval of building supervision.

BEGA-34067.1-Ceiling-and-Wall-Luminaire-03

Installation

Remove the luminaire from its packaging and lay it out on a soft surface.

Open the luminaire:
Use a hex key (size 3) to open the ceiling bracket on the housing ring with a quarter turn to the left.
Open the ceiling bracket fully by slightly tilting the torsion spring back a little.

BEGA-34067.1-Ceiling-and-Wall-Luminaire-04

Raise the installation box carefully and disconnect the LED connectors to the left and right side.
Unscrew the 3 nuts above the hinge until the end of thread using a socket wrench (size 8) or a ratchet.
Pull the safety clamp forward and take off the installation box upwards.

BEGA-34067.1-Ceiling-and-Wall-Luminaire-05

Note position of application “arrow down” when installed at the wall; the safety clamp has to show to the top!
Fix installation box with enclosed or any other suitable fixing material onto the mounting surface.

Lead mains supply cable through one of the 4 cable entries into the installation box.
Make earth connection and electrical connection to terminals.
For digital control please use the connecting terminal DA, DA.
In case this terminal is not used the luminaire will be operated at full light output.
Pick up the luminaire and insert the hinge laterally to the arrester.
Screw the three hex-nuts sittings above the hinge tightly – torque 3.4 Nm.

Attention:
The luminaire is only then securely attached
to the ceiling bracket when all three nuts are tightened!
Reconnect the LED plug connectors to the left and right of the ceiling bracket.
Close luminaire as far as to the spring arrester. Insert an Allen wrench (size 3) into the locking system at the housing ring and turn it against the spring resistance to the left.
Press the luminaire into the final position and observe that the countersunk socket screw is properly locked in the initial position.

Deinstallation
Disconnect the electrical installation.

ATTENTION:
Once the closure system is unlocked, the weight of the luminaire must be supported! To open the luminaire unscrew the locking system of the installation box by turning it with an Allen key (no. 3) for a quarter-turn to the left. Support the weight of the luminaire until the torsion spring engages.
For the complete opening of the installation box incline the torsion spring backwards out of the arrester and swing out the luminaire. Disconnect the LED connectors to the left and right side.
Unscrew the 3 nuts above the hinge until the end of thread using a socket wrench (size 8) or a ratchet.
Pull the safety clamp forward and take off the luminaire.
Place luminaire on repository.

Relamping · Maintenance
DE install luminaire according to instructions. Open luminaire and remove LED- unit. Disassemble LED module.
Assemble LED replacement module.

Note installation instructions of the LED module.

Reassemble LED-unit
Check the gasket and replace, if necessary. Clean glass and luminaire regularly with solvent-free cleansers from dirt.
Close the luminaire.
Make sure that gasket is positioned correctly. A broken glass must be replaced.

Spares