BEGA 50039 Ceiling and Wall Luminaire Instruction Manual

BEGA 50039 Ceiling and Wall Luminaire

Product Information

This product is a luminaire designed for lighting purposes. It is equipped with LED technology and has a maximum power consumption of 11.3 W. The luminaire has a rated temperature range of 25 to 40 degrees Celsius. It is available in two different color temperature options: 2700 K and 3000 K. The color rendering index (CRI) of both options is greater than 90. The module luminous flux for the 2700 K option is 1165 lm, while for the 3000 K option it is 1205 lm. The luminaire has a luminous efficiency of 51.4 lm/W for the 2700 K option and 51.9 lm/W for the 3000 K option.

The installation and operation of this luminaire should be done in accordance with national safety regulations. Only a qualified electrician should carry out the installation and commissioning process. The manufacturer does not accept liability for any damage caused by improper use or installation. It is recommended to use separate overvoltage protection components to provide additional protection against transients and other electrical issues.

Product Usage Instructions

• Before installing the luminaire onto the mounting surface, insert the luminaire housing into the trim ring accessory.
• During installation or relamping, avoid touching the light output opening of the LED directly.
• To release the glass from the luminaire housing, turn it counterclockwise.
• The maximum wall mounting height for this luminaire is 2.7 m, while the maximum ceiling mounting height is 4.0 m. Metal parts mounted close to the luminaire can affect its range, so it is important to consider this when positioning the luminaire.
• The motion sensor integrated into the luminaire has three push buttons for specific settings. Pressing a push-button activates the setting function, and each subsequent press switches the function to the next level. The LED indicator on the motion sensor flashes to confirm the selection. After reaching the highest level, the level setting begins with Level 1.

Application

• Ceiling and wall luminaire · indoor luminaire made of hand-blown opal glass and metal housing, for all lighting tasks. They are ideal for places where a soft and uniform lighting distribution is required.
• Luminaire with motion sensor.

Product Description

• Metal housing, finish Colour white
• Hand-blown opal glass, satin matt, with bayonet closure
• Integrated HF-motion sensor, maximum range 10 m
• 2 mounting holes ø 5.5 mm
• Distance apart 180 mm
• 2 cable entries for through-wiring for mains cable up to ø 10.5 mm max. 3 × 1.5@
• Connection terminal 2.5@
• Earth conductor connection
• LED power supply unit 230 V y 50 Hz
• BEGA Thermal Switch®
• Temporary thermal shutdown to protect temperature-sensitive components
• Safety class I
  • Conformity mark
• Weight: 1.7 kg
• This product contains light sources of energy efficiency class(es) D, E

Safety

• The installation and operation of this luminaire are subject to national safety regulations.
• Installation and commissioning may only be carried out by a qualified electrician.
• The manufacturer accepts no liability for damage caused by improper use or installation.
• If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Overvoltage protection

• The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547.
• To achieve additional protection against e. g. transients, etc. we recommend separate overvoltage protection components.
• You can find them on our website at www.bega.com.

Lamp Specification

• Module connected wattage 8.2 W
• Luminaire connected wattage 11.3 W
• Rated temperature ta = 25 °C
• Ambient temperature ta max = 40 °C

50 039 K27

• Colour temperature 2700 K
• Colour rendering index CRI > 90
• Module luminous flux 1165 lm
• Luminaire luminous flux * 581 lm
• Luminaire luminous efficiency * 51,4 lm / W

50 039 K3

• Colour temperature 3000 K
• Colour rendering index CRI > 90
• Module luminous flux 1205 lm
• Luminaire luminous flux * 587 lm
• Luminaire luminous efficiency * 51,9 lm / W

preliminary data

Luminaire with trim ring:
Before installing onto the mounting surface the luminaire housing must be inserted into the trim ring (accessory).

Installation

• LED are high-quality electronic components!
• Please avoid touching the light output opening of the LED directly during installation or relamping.
• Pass the main supply cable through the grommet into the luminaire housing.
• Fix luminaire housing with enclosed or any other suitable fixing material on to the mounting surface.
• It is imperative to use the enclosed gaskets.
• Dismantle the mains supply cable approx. 60 mm.
• Make earth and electrical connections to the terminals.
• Place glass in the luminaire housing and observe that the cam pins fit into the notches of the glass.
• Screw in the glass by turning it clockwise.
• Thus, you reach a safe and vibration-resistant holding of the glass.
• To release the glass from the luminaire housing, turn it counterclockwise.
• The built-in motion sensor operates at a frequency of 5.8 GHz.
• By moving within the detection range the motion sensor switches on the LED module inside the luminaire with a defined dwell time – push-button “Dwell time”.
• With a wall mounting height of 1.8 m or a ceiling mounting height of 2.6 m, the maximum range is 10 meters (see sketch).
• The max. wall mounting height is 2.7 m and the max. ceiling mounting height is 4.0 m, in which the range reduces significantly.
• The range can be set individually – push-button “Sensitivity”.

It should be noted that metal parts that are mounted in close proximity to the luminaire can affect the range.

Dimension

With the three integrated push-buttons

• (Brightness, Dwell time, and Sensitivity) on the motion sensor, specific settings can be made.
• The first keypress activates the setting function.
• Press a push-button to switch each function to the next level, and the LED indicator on the motion sensor flashes to confirm.
• After reaching the highest level, the level setting begins with “Level 1”.

• After the 3 parameters brightness, dwell time, and sensitivity have been set successfully the module will require a voltage break to save the changes.
• The integrated light sensor can be set individually with the brightness levels on the ambient brightness – Press the button “Brightness”.
• Further individual illumination levels can be used with the button “Brightness” and set with the “learning mode”.
• Press the button “brightness” (> 3 s) to enable the “learning mode”. There is a slow flashing of the LED indicator.
• After about two minutes, the current brightness value is measured for one minute, the LED flashes faster.
• After completion, the measured brightness value is saved and is available in stage 6 of “Brightness” as the new brightness value.

To simplify the initial operation, the settings have been made as follows:

• Range = 75 % (7.5 m)
• Dwell time = 10 s
• Light sensor = daylight

Factory Reset

The motion sensor can be reset to factory settings (MICAS) by simultaneously pressing the buttons “Sensitivity” and “Dwell time” for about 5 s.

The factory settings are as follows:

• Range = 75 % (7.5 m)
• Dwell time = 900 s
• Light sensor = daylight

Test mode

• The test mode can be used to check the change of settings of the motion sensor.
• Press the button “Sensitivity” (> 3 s) to enable the “test mode”.
• Each further keystroke of this push-button prolongs the test mode.
• The active test mode is displayed by a flashing of the LED indicator (2 s interval).
• After 3 minutes the test mode is automatically disabled.

Replacement of the LED unit

• The designation of the LED unit is noted on a label in the luminaire.
• The light colour and light output of BEGA replacement units correspond to those of the LED units originally fitted. The LED unit can be replaced by qualified persons using standard tools.
• Disconnect from the main supply.
• Unscrew the glass from the luminaire housing by turning it counter-clockwise.
• Replace the LED unit.
• Screw in the glass by turning it clockwise.
• The defective glass must be replaced.

Accessory And Trim rings

• For this luminaire metal trim rings in 3 enamel surfaces are optionally available.
• Trim rings are accessories and must be ordered separately.

Item/Part. No

• Colour white 13 001
• Colour palladium 13 002
• Colour glossy silver 13 003

Spares

• Spare glass 11 003 179 .0R G
• HF-motion sensor 61 001 077
• LED unit 2700 K 75 003 045 K27
• LED unit 3000 K 75 003 045 K3

BEGA Gantenbrink-Leuchten KG · Postfach 31 60 · 58689 Menden · info@bega.com · www.bega.com.

References

• BEGA · Das gute Licht.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>