BEGA 50813.6 Recessed Ceiling Luminaire Instruction Manual

BEGA 50813.6 Recessed Ceiling Luminaire

Product Information

• Safety: The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning should be carried out by a qualified electrician. The manufacturer is not liable for damage caused by improper use or installation.
• Overvoltage Protection: The electronic components installed in the luminaire are protected against overvoltage according to DIN EN 61547. Additional protection against transients is recommended through separate overvoltage protection components, available on the manufacturer’s website.
• Lamp:
  • Lamp Module Connected Wattage: 7.8 W
  • Luminaire Connected Wattage: 9.8 W
  • Rated Temperature: 25 – 45°C
  • Ambient Temperature: max 45°C
• Module:
  • Module Designation: LED-1021/930
  • Colour Temperature: 3000 K
  • Colour Rendering Index (CRI): >90
  • Module Luminous Flux: 1180 lm
  • Luminaire Luminous Flux: 402 lm
  • Luminaire Luminous Efficiency: 41 lm/W

Product Usage Instructions

1. Installation:
   • The luminaire housing and external LED power supply unit should not be covered by any heat-insulating materials.
   • Avoid touching the light output opening of the LED directly during installation or relamping.
2. Replacing the LED Module:
   • Check the label in the luminaire to find the designation of the LED module.
   • BEGA replacement modules have the same light color and light output as the originally fitted modules.
   • Qualified persons can replace the module using standard tools.
   • Disconnect the system and open the luminaire.
   • Follow the installation instructions provided for the LED module.
   • Close the luminaire after replacing the module.

Application

• Recessed ceiling luminaire · indoor luminaire with symmetrical wide beam light distribution and a remote non-dimmable power supply unit.
• For installation in suspended ceilings of 5-30 mm in interior applications.

Product Description

• Recessed LED ceiling luminaire with a remote power supply unit
• Luminaire housing made of cast aluminum
• Ceiling trim ring finish, Colour velvet black
• Inside hue matt copper
• Fixing is achieved by using 2 fastening springs
• Recessed opening ø 100 mm
• Required installation depth 75 mm
• Light-diffusing disc
• External LED power supply unit 220-240 V x 0/50-60 Hz
• Safety class II 2
  • Safety mark
  • Conformity mark
• Weight: 0.35 kg
• This product contains light sources of energy efficiency class(es) D

Safety

• The installation and operation of this luminaire are subject to national safety regulations.
• Installation and commissioning may only be carried out by a qualified electrician.
• The manufacturer accepts no liability for damage caused by improper use or installation.
• If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Overvoltage Protection

• The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547.
• To achieve an additional protection against e. g. transients, etc. we recommend separate overvoltage protection components.
• You can find them on our website at www.bega.com.

Lamp

• Module connected wattage 7.8 W
• Luminaire connected wattage 9.8 W
• Rated temperature ta = 25 °C
• Ambient temperature ta max = 45 °C

50 813.6 K3

• Module designation LED-1021/930
• Colour temperature 3000 K
• Colour rendering index CRI > 90
• Module luminous flux 1180 lm
• Luminaire luminous flux 402 lm
• Luminaire luminous efficiency 41 lm / W

Installation

• Luminaire housing and external LED power supply unit must not be covered by any heat insulating materials.
• LED are high-quality electronic components! Please avoid touching the light output opening of the LED directly during installation or relamping.
• Cover the recessed opening with the stop ring of the luminaire housing.
• The luminaire housing is then fixed in the recessed opening via two springs.

Installation in suspended ceilings:

• A recessed opening of 100 mm with a minimum depth of 75 mm is required.
• The minimal thickness of the ceiling panel must be 5 mm and must not be greater than 30 mm.
• A ceiling panel with less than 5 mm thickness must be reinforced on the reverse.
• The electrical connection must be made on site in the appropriate safety class on the LED power supply unit connecting cable. A distribution box must be used.
• Ensure the correct assignment of the connecting cable. Establish the mains connection on the brown (L) and blue (N) wires.
• Guide the LED power supply unit through the opening in the ceiling and position it on the suspended ceiling.
• Compress the fastening springs of the luminaire housing on both sides and slide the luminaire housing into the recessed opening.
• The fastening springs lock into place behind the ceiling panel.

Dimension

Cleaning And Maintenance

Clean luminaire regularly with solvent-free cleansers from dirt.

Replacing the LED module

• The designation of the LED module is noted on a label in the luminaire.
• The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted. The module can be replaced by qualified persons using standard tools.
• Disconnect the system and open the luminaire. Please follow the installation instructions for the
• LED module.
• Close the luminaire.

Spares

• LED power supply unit DEV-0375/350
• LED module 3000 K LED-1021/930

BEGA Gantenbrink-Leuchten KG · Postfach 31 60 · 58689 Menden · info@bega.com · www.bega.com.

References

• BEGA · Das gute Licht.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>