BEGA 24489 Wall Luminaire Instruction Manual

: June 12, 2024
: BEGA

Table of Contents

BEGA 24489 Wall Luminaire
Product Information
Product Usage Instructions
Instructions for use
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BEGA 24489 Wall Luminaire

Product Information

Product Name	Wandleuchte Wall luminaire Applique
Light Distribution	Asymmetrical
Application	For lighting wall and ground surfaces
Dark Sky	The light from this luminaire is directed evenly and highly

efficiently onto the surface to be illuminated and emits less than
1% of the luminaire luminous flux into the upper halfspace of the
luminaire.
Overvoltage Protection| The electronic components installed in the luminaire are
protected against overvoltage in accordance with DIN EN 61547.
Separate overvoltage protection components are recommended for
additional protection.
Safety| The installation and operation of this luminaire must comply
with national safety regulations. Only a qualified electrician
should carry out the installation and commissioning. The
manufacturer is not liable for damage caused by improper use or
installation.

Product Usage Instructions

Mount the mounting plate using the provided or suitable fastening material on the installation surface.
Tighten the cable gland securely.
Establish the protective earth connection and make the electrical connection to the terminal (plug-in device).
To control the luminaire digitally, use the terminals DA, DA.
If these terminals are not connected, the luminaire will operate at full light output.

Wall luminaire

BEGA-24489-Wall-Luminaire-01

Instructions for use

Application
Wall luminaire with asymmetrical light distribution.
For lighting wall and ground surfaces.

Product description

Luminaire made of aluminum alloy, aluminum and stainless steel
BEGA Unidure® coating technology
Safety glass, antireflection-coated
Silicone gasket
Reflector surface made of pure aluminium Mounting plate with 3 elongated holes, Width 6.5 mm · 80 x 145 mm spacing
2 screw cable glands with strain relief for through-wiring power connecting cable ø 7–12 mm
1 screw cable gland closed at the factory with a dummy plug
Connecting terminal 2.5@ with plug connection
Earth conductor connection
BEGA Ultimate Driver®
LED power supply unit 220-240 V x 0/50-60 Hz
DC 176-264 V
DALI-controllable
Number of DALI addresses: 1
Basic insulation is provided between the mains and control cables
BEGA Thermal Control®
Temporary thermal regulation to protect temperature-sensitive components without switching off the luminaire
Safety class I
Protection class IP 66
Dust-tight and protection against strong water jets
Impact strength IK07
Protection against mechanical impacts < 2 joule
– Safety mark
CE – Conformity mark
Weight: 4.8 kg

This product contains light sources of energy efficiency class(es) C

Dark Sky
The light from this luminaire is directed evenly and highly efficiently onto the surface to be illuminated and emits less than 1 % of the luminaire luminous flux into the upper half-space of the luminaire.

Overvoltage protection
The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e. g. transients, etc. we recommend separate overvoltage protection components.
You can find them on our website at www.bega.com.

Safety
The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Lamp

Module connected wattage 31 W
Luminaire connected wattage 33.5 W
Rated temperature ta = 25 °C
Ambient temperature ta max = 55 °C

24 489 K3

Module designation LED-1080/830
Colour temperature 3000 K
Colour rendering index CRI > 80
Module luminous flux 6020 lm
Luminaire luminous flux * 4668 lm
Luminaire luminous efficiency * 139,3 lm / W

24 489 K4

Module designation LED-1080/840
Colour temperature 4000 K
Colour rendering index CRI > 80
Module luminous flux 6190 lm
Luminaire luminous flux * 4800 lm
Luminaire luminous efficiency * 143,3 lm / W
preliminary data

Installation
Undo hexagon socket head screws (wrench size 3 mm) up to the stop and disassemble the mounting plate.
Pass the power connecting cable through the cable entry in the mounting plate.
The installed black gasket insert is intended for cables ø < 10 mm.
For cables ø 10-12 mm the enclosed grey gasket insert must be used.
In case of through-wiring replace the factory installed dummy plug with the enclosed corresponding gasket insert.
At the same time, use the enclosed synthetic cone-thrust collar between gasket insert and thrust screw (wrench size 22 mm) (see sketch).

BEGA-24489-Wall-Luminaire-02

Fix the mounting plate with enclosed or any other suitable fixing material onto the mounting surface.
Tighten screw cable gland.
Make earth conductor connection and electrical connection to the connecting terminal (plug connection).
For digital control please use the connecting terminal DA, DA.
In case this terminal is not used the luminaire will be operated at full light output.

Make sure that gasket is positioned correctly. Push plug into coupler as far as it will go. Place the luminaire onto the mounting plate and fix it.

Please note:
Do not remove the desiccant bag from the luminaire housing.
It is needed to remove residual moisture.

Cleaning · Maintenance
Clean luminaire regularly with solvent-free cleansers from dirt and deposits.
Do not use high pressure cleaners.

Replacing the LED module
The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted.
The module can be replaced by qualified persons using standard tools.
Disconnect the system and open the luminaire. Please follow the installation instructions for the LED module.
Inspect and, if necessary, replace the luminaire gaskets.
Defective glass must be replaced.
Close the luminaire.

Spares