BEGA 89758.1 Ceiling and Wall Luminaire Instruction Manual
- June 12, 2024
- BEGA
Table of Contents
BEGA 89758.1 Ceiling and Wall Luminaire
Product Information
The product is a luminaire, designed for lighting purposes. It has a luminaire efficiency of 41%. Detailed technical and lighting data can be found in the data sheets on the manufacturer’s website.
Product Usage Instructions
- Safety: The installation and operation of the luminaire must adhere to national safety regulations. Only a qualified electrician should carry out the installation and commissioning. The manufacturer is not liable for damage caused by improper use or installation. Any modifications to the luminaire should be done by the person responsible for those modifications.
- Sliding-Bolt Closure: To securely hold the glass, follow these steps:
- Place the glass on the base plate.
- Ensure that the holding springbolts fit into the notches of the glass.
- Rotate the glass clockwise until it locks in place.
This will provide a safe and vibration-resistant holding of the glass. To release the glass from the base plate, turn it counter-clockwise.
- Spares: The following spare parts are available for the product:
- Spare glass
- LED lamp 2700 K
- LED lamp 3000 K
- Lampholder
The corresponding part numbers for these spares are:
* 11 002 770 .0R G
* 13 548
* 13 586
* 63 000 187Instructions for use
Application
Ceiling and wall luminaire · indoor luminaire made of hand-blown opal glass,
satin matt and metal housing, for all lighting tasks. They are ideal for
places where a soft and uniform lighting distribution is required. Luminaire
with a high protection class.
Lamp
Luminaire with screw base E 27 Lamp output max. 2 × 60 W This product contains
light sources of energy efficiency class E
Supplied lamp
2 × BEGA LED lamp 13548
LED Retrofit 7 W · 805 lm · 2700 K dimmable
Supplied lamp
2 × BEGA LED lamp 13586
LED Retrofit 7 W · 805 lm · 3000 K dimmable
Luminaire efficiency: 41%
Detailed technical and lighting data for the lamps can be found in the data
sheets on our website.
Product Description
Metal housing, finish Colour white Hand-blown opal glass, satin matt, with
sliding-bolt closure 2 mounting holes ø 5.5 mm Distance apart 187,9 x 68,4 mm
2 cable entries for through-wiring for mains cable up to ø 10.5 mm max. 3 ×
1.5@ Connection terminal 2.5@ Earth conductor connection Lampholder E 27
Safety class I Protection class IP 44 Protected against granular foreign
bodies ≥ 1 mm and splash water Impact strength IK05 Protection against
mechanical impacts < 0.7 joule
r – Safety mark
c – Conformity mark
Weight: 3.4 kg
Safety
The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician. The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.
Installation
Pass the mains supply cable through the mounting plate. Notice position of application »arrow down« when installed at the wall. Fix base of the luminaire with enclosed or any other suitable fixing material on to the mounting surface. It is imperative to use the enclosed gaskets. Make earth conductor connection. Push silicone sleeves over the lines and make electrical connection.
Insert lamp.
Insert the opal glass into the luminaire base with sliding bolt glass closure
and turn the glass clockwise up to the stop.
The sliding-bolt closure
The sliding-bolt closure provides a safe and vibration-resistant holding of
glass. Place glass to the base plate and observe that the holding springbolts
fit into the notches of the glass. Turn the glass clockwise until it is
locked. Thus, you reach a safe and vibration-resistant holding of the glass.
To release the glass from the base plate, turn it counter-clockwise.
Relamping · Maintenance
Disconnect from main supply. Remove glass turning it counter-clockwise. Clean glass. Use only solvent-free cleansers. Change the lamp. Place glass into fitter and turn it clockwise until the stop.
Spares
- Spare glass: 11 002 770 .0R G
- LED lamp 2700 K: 13 548
- LED lamp 3000 K: 13 586
- Lampholder: 63 000 187
BEGA Gantenbrink-Leuchten KG
Postfach 31 60
58689 Menden
[email protected]
www.bega.com