BEGA 50698.1 Recessed Ceiling Downlight Instruction Manual

BEGA 50698.1 Recessed Ceiling Downlight

Product Information

• Product Description: Recessed luminaire without power supply unit
• Luminaire Housing: Made of cast aluminium
• Installation Housing: Made of glass-fibre reinforced polyamide with 2 fastening springs
• Reflector: Made of pure anodised aluminium
• Required Installation Depth: 130 mm
• Weight: 2.0 kg
• Energy Efficiency Class: E
• Safety: The installation and operation of this luminaire are subject to national safety regulations. Only a qualified electrician should carry out the installation and commissioning. The manufacturer does not accept liability for damage caused by improper use or installation.
• Overvoltage Protection: The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547. Additional protection against transients is recommended with separate overvoltage protection components.
• Lamp Module Connected Wattage: 17.2 W
• Luminaire Connected Wattage: 19.8 W
• Colour Temperature: 3000 K
• Colour Rendering Index (CRI): > 90
• Module Luminous Flux: 2655 lm
• Luminaire Luminous Flux: 1838 lm
• Luminaire Luminous Efficiency: 92.8 lm/W

Product Usage Instructions

1. The installation and operation of this luminaire should only be done by a qualified electrician.
2. Ensure that the national safety regulations are followed during installation and operation.
3. A separate power supply unit is required to operate the luminaire.
4. Refer to the operating instructions of the LED-power supply units.
5. Avoid touching the light output opening of the LED directly during installation or relamping.
6. The recessed opening should not be installed in heat-insulating material.
7. Fix the installation housing in the recessed opening using the two adjustable fastening springs.

DIMENSIONS

Instructions for use

Application

• Recessed ceiling luminaire · indoor luminaire with direct and indirect light distribution for connection to an external LED power supply unit.
• For surface-mounted installation in indoor suspended ceilings of 8-25 mm thickness.

Product Description

• Recessed luminaire without power supply unit Luminaire housing made of cast aluminium Installation housing is made of glass-fibre reinforced polyamide with 2 fastening springs Reflector made of pure anodised aluminium Light-diffusing silicone lens
• Ceiling trim ring made of metal, Colour white Hand-blown opal glass, satin matt
• Recessed opening ø 188 mm
• Required installation depth 130 mm
• 1 connecting cable with strain relief and plug connector system for BEGA power supply unit, on/off or DALI

Safety class III 3

• CE  – Conformity mark
• Weight: 2.0 kg
• This product contains light sources of energy efficiency class(es) E

Safety

• The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician.
• The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Overvoltage protection

• The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547.
• To achieve an additional protection against e. g. transients, etc. we recommend separate overvoltage protection components.
• You can find them on our website at www.bega.com.

Lamp

• Module connected wattage 17.2 W
• Luminaire connected wattage 19.8 W
• Rated temperature ta = 25 °C
• Ambient temperature ta max = 40 °C

50 698.1 K3

• Module designation LED-0785/930
• Colour temperature 3000 K
• Colour rendering index CRI > 90
• Module luminous flux 2655 lm
• Luminaire luminous flux 1838 lm
• Luminaire luminous efficiency 92,8 lm / W

Lighting technology

• Half beam angle 50°

Installation

Luminaire housing must not be installed in heat-insulating material.

A separate power supply unit is required to operate the luminaire.

• For connection to external LED-power supply unit – accessory 13 144 or 13 170 – the luminaire is equipped with a 2-pin connector. Note operating instructions of the LED-power supply units.
• LED are high-quality electronic components!Please avoid touching the light output opening of the LED directly during installation or relamping.
• The recessed opening is covered by the frame of the luminaire housing.
• Fixing of the installation housing in the recessed opening is achieved by using two adjustable springs.

Installation into inserted ceilings:

• A recessed opening of 188 mm is necessary to accept the installation housing. Recessed depth min. 130 mm.

• The lateral distance between recessed luminaire and other building parts must be at least 50 mm.

• Compress the fastening springs of the installation housing against their spring pressure on both sides towards the housing and slide the installation housing into the recessed opening.

• The fastening springs catch the ceiling panel from the back side. Minimum thickness of the ceiling panel is 8 mm. If minimum thickness of the panel is less than 3 mm it must be reinforced from the reverse side. Maximum thickness of the ceiling panel must be no more than 25 mm.

• Push the enclosed threaded rods through the two inside openings of the installation housing and guide the clamping angle of the threaded rods downwards onto the suspended ceiling. Clip the threaded rods into their guide grooves and screw them in by hand as far as possible. Fix in end position with screwdriver (TX 10). This clamp fixing prevents the installation housing from turning and dropping.

• Connect to the LED power supply unit. Route the LED power supply unit through the installation housing and place it in the suspended ceiling.

• Connect the 2-pin plug connector between luminaire and external LED power supply unit.

• Press together the two internal fixing sliders inside the luminaire housing.

• Push the luminaire housing to the end of the installation housing and then release the fixing sliders.

• This mechanism ensures that the luminaire housing sits securely inside the installation housing.

• Installation housing and external LED-power supply unit must not be installed in heat-insulating material.

• Please use the protective gloves provided for the installation to prevent finger prints on the reflector.

• Place the reflector with silicone lens on the ceiling trim ring. Twist the ceiling trim ring complete with the attached reflector to the right to fix the assembly inside the luminaire housing.

Cleaning · Maintenance

• Clean luminaire regularly with solvent-free cleansers from dirt.

Replacing the LED module

• The designation of the LED module is noted on a label in the luminaire.
• The light colour and light output of BEGA replacement modules correspond to those  of the modules originally fitted. The module can be replaced by qualified persons using standard tools.
• Disconnect the system and open the luminaire. Please follow the installation instructions for the LED module.
• Close the luminaire.

Accessories

• Power supply units for LED luminaires 220-240 V · 0/50-60 Hz with strain relief and plug connector system.
• 13 144 Power supply unit on/off
• 13 170 Power supply unit DALI
• The power supply units are only suitable for the operation of one LED luminaire.
• For the accessories a separate instructions for use can be provided upon request.

Spares

• Spare glass 11 003 450 .0M 1RG
• LED module 3000 K LED-0785/930
• Reflector 75 002 753

BEGA Gantenbrink-Leuchten KG · Postfach 31 60 · 58689 Menden · info@bega.com · www.bega.com

References

• BEGA · Das gute Licht.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>