BEGA 38301 Ceiling and Wall Luminaire Instruction Manual

: June 12, 2024
: BEGA

Table of Contents

BEGA 38301 Ceiling and Wall Luminaire
Product Information
Product Usage Instructions
Instructions for use
Product Description
Safety
Installation
Cleaning · Maintenance
Replacing the LED module
Spares
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BEGA 38301 Ceiling and Wall Luminaire

BEGA-38301-Ceiling-and-Wall-
Luminaire-product

Product Information

Product Name: Decken- und Wandleuchte (Ceiling and wall luminaire)
Model Number: 38 301 K3
Lamp Type: LED
Colour Temperature: 3000 K
Colour Rendering Index (CRI): Ra > 80
Lamp Luminous Flux: 2160 lm
Luminaire Luminous Flux: 1780 lm
Luminaire Luminous Efficiency: 89 lm / W
Material: Aluminium alloy
Glass Type: Opal glass satin matt
Distance Apart: 170 mm
Cable Entries: 2 for through-wiring of mains
Connection Terminal: 2.5@
Safety Class: I
Protection Class: IP 44
Impact Strength: IK03

Product Usage Instructions

Ensure that the installation and operation of the luminaire comply with national safety regulations.
Only a qualified electrician should carry out the installation and commissioning.
Avoid touching the light output opening of the LED directly during installation or relamping.
To install, lead the mains supply cable through the cable entry of the luminaire base.
Fix the luminaire base onto the mounting surface using the provided fixing material.
Make sure to use the gasket rings supplied.
Make the earth conductor connection.
Push silicone sleeves over the lines and make electrical connection.
Snap the opal glass into the lower spring clips, centralize, and push into the upper spring clips.
To clean the luminaire, remove the glass from the clips and clean it separately.
Do not use high-pressure cleaners.
Replacement modules are available in the market.
Work on the luminaire only when it is disconnected from the power supply.

Instructions for use

Application
Lichtbaustein® Square
Ceiling and wall luminaire for many lighting tasks.
Ideal for places where a soft and uniform lighting distribution is required.

Lamp
Luminaire connected wattage: 20 W
Rated temperature: ta = 25 °C
Ambient temperature: ta max = 35 °C

38 301 K3
Module designation: 2x LED-1249/830
Colour temperature: 3000 K
Colour rendering index: Ra > 80
Module luminous flux: 2160 lm
Luminaire luminous flux: 1780 lm
Luminaire luminous efficiency: 89 lm / W

Product Description

Luminaire made of aluminium alloy and stainless steel
BEGA Unidure® coating technology Opal glass satin matt 2 mounting holes ø 4.8 mm
Distance apart 170 mm 2 cable entries for through-wiring of mains supply cable ø 7-10.5 mm 4 prefabricated cable ducts for surface mounted mains supply cables
Connecting terminal and earth conductor terminal 2.5@
LED-Module for mains voltage
220-230 V y 50/60 Hz
BEGA Thermal Switch®
Temporary thermal shutdown to protect temperature-sensitive components
Safety class I
Protection class IP 44
Protected against granular foreign bodies
≥ 1 mm and splash water
Impact strength IK03
Protection against mechanical
impacts < 0.35 joule
– Safety mark
– Conformity mark
Weight: 3.1 kg
This product contains light sources of energy efficiency class(es) F

Safety

The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician. The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Installation

LED are high-quality electronic components! Please avoid touching the light output opening of the LED directly during installation or relamping. Lead the mains supply cable through the cable entry of the luminaire base. Fix luminaire base with enclosed or any other suitable fixing material onto the mounting surface. Be sure to use the gasket rings supplied. Make earth conductor connection. Push silicone sleeves over the lines and make electrical connection. Snap the opal glass into the lower spring clips, centralise and push into the upper spring clips.

Cleaning · Maintenance

Clean the luminaire regularly with solvent-free cleansers from dirt and deposits. Do not use high pressure cleaners.

Replacing the LED module

The designation of the LED module is noted on a label in the luminaire. The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted. The module can be replaced by a qualified electrician or a comparably qualified person using standard tools. Disconnect the electrical installation. Pull glass out of the spring clips and remove from the luminaire back housing. Clean the glass and luminaire housing using only suitable cleansers. When cleaning please do not use high pressure cleaners. Please follow the installation instructions for the LED module. A broken glass must be replaced. Snap the glass into the lower spring clips, centralise and push into the upper spring clips.