BEGA 50818.2 Indoor Wall Luminaire Instruction Manual

: June 12, 2024
: BEGA

Table of Contents

BEGA 50818.2 Indoor Wall Luminaire
Product Information
Product Usage Instructions
Dimensions
Instructions for use
Product Description
Safety
Overvoltage protection
Installation
Cleaning · Maintenance
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BEGA 50818.2 Indoor Wall Luminaire

Product Information

Product Name: LED Luminaire
Model Number: 50 818.2 K3
Module Designation: LED-0393/930
Colour Temperature: 3000 K
Colour Rendering Index (CRI): > 90
Module Luminous Flux: 1840 lm
Luminaire Luminous Flux: 821 lm
Luminaire Luminous Efficiency: 59.9 lm / W

Product Usage Instructions

Ensure that the installation and operation of the luminaire comply with national safety regulations. Only a qualified electrician should carry out the installation and commissioning.
To protect against overvoltage, it is recommended to use separate overvoltage protection components in addition to the built-in protection.
Prepare the mounting plate by using the provided or suitable fastening material to attach it securely to the installation surface.
Undo the hexagon socket head screws on the luminaire housing and lift the housing.
Take caution not to touch the light output opening of the LED directly during installation or relamping.
Loosen the earth connection and LED connection between the luminaire housing and mounting plate.
Pass the power connecting cable through the cable entry in the mounting plate.
Attach the luminaire housing onto the mounting plate and tighten the hexagon socket head screws evenly.
Insert the supplied shield into the luminaire housing, ensuring that it engages with its magnetic underside flush to the profile groove of the housing.
Refer to the LED module’s installation instructions for any specific guidelines. Replace any defective LED covers.
To loosen the screw connection of the LED module, first loosen the hexagon nuts on the inside and remove the metal plate from the luminaire housing.
Remove the loose luminaire cover and press the synthetic LED cover together lengthwise to remove it from the housing profile.
Remove the LED module and install the replacement module following the installation instructions.
Reassemble the luminaire in reverse order.

Please note that any modifications made to the luminaire are the responsibility of the person who made them and may void the manufacturer’s liability for any resulting damage.

Dimensions

BEGA-50818.2-Indoor-Wall-Luminaire-fig-1

Instructions for use

Application
Wall luminaire · indoor luminaire with velvet white luminaire housing and inside hue. Luminaire with shielded light source for illumination of wall surfaces with the mounting surface being the reflection surface. The light emits upwards and downwards.

Product Description

Wall luminaire “STUDIO LINE”
Luminaire housing made of aluminium, surface Colour velvet white inside hue aluminium matt
Light-diffusing synthetic LED cover
2 elongated fixing holes
Width 4.5 mm · 210 mm spacing
1 cable entry for through-wiring for mains cable
Connection terminal 2.5@
Earth conductor connection
LED power supply unit
220-240 V x 0/50-60 Hz
DC 176-280 V
BEGA Thermal Switch®
Temporary thermal shutdown to protect temperature-sensitive components

Safety class I

– Safety mark
– Conformity mark
Weight: 0.9 kg

This product contains light sources of energy efficiency class(es) D

Lamp

Module connected wattage 11.8 W
Luminaire connected wattage 13.7 W
Rated temperature ta = 25 °C
Ambient temperature ta max = 55 °C

50 818.2 K3

Module designation LED-0393/930
Colour temperature 3000 K
Colour rendering index CRI > 90
Module luminous flux 1840 lm
Luminaire luminous flux 821 lm
Luminaire luminous efficiency 59,9 lm / W

Safety

The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Overvoltage protection

The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e. g. transients, etc. we recommend separate overvoltage protection components.
You can find them on our website at www.bega.com.

Installation

Undo the hexagon socket head screws (wrench size 2.5 mm) and lift luminaire housing. LED are high-quality electronic components! Please avoid touching the light output opening of the LED directly during installation or relamping.
Loosen earth connection (plug connection) and LED-connection (plug – plug socket) between luminaire housing and mounting plate.
Pass the power connecting cable through the cable entry in the mounting plate. Fasten the mounting plate with the supplied fastening material or other suitable fastening material to the installation surface.
Make sure to use the gaskets supplied. Establish earth conductor connection and make the electrical connection to the terminals. Restore the earth conductor connection (plug contact) and LED connection (plug–jack) between the luminaire housing and the mounting plate.
Install luminaire housing onto the mounting plate and tighten hexagon socket head screws evenly.
Carefully insert the supplied shield into the luminaire housing. Make sure that in its final position, the shield engages with its magnetic underside flush to the profile groove of the luminaire housing.

Cleaning · Maintenance

Clean luminaire regularly with solvent-free cleansers from dirt.
Replacing the LED module
The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted. The module can be replaced by qualified personnel using standard tools.
Disconnect the system from the mains.
Undo the hexagon socket head screws (wrench size 2.5 mm) and lift luminaire housing. Loosen earth connection (plug connection) and LED-connection (plug – plug socket) between luminaire housing and mounting plate.
In order to loosen the screw connection of the LED module, first loosen the hexagon nuts on the inside and remove the metal plate from the luminaire housing. Remove the loose luminaire cover.
Press the synthetic LED cover together lengthwise and remove it from the housing profile.
Remove the LED module. Install the replacement LED module.
Please follow the installation instructions for the LED module.
A defective LED cover must be replaced. Install the luminaire again in the reverse order.