BEGA 50139.2K3 LED Wall Luminaire Instruction Manual
- June 12, 2024
- BEGA
Table of Contents
BEGA 50139.2K3 LED Wall Luminaire
Product Information
- Product Name: Luminaire – Model: K3 – Lamp
- Type: LED – Lamp Power: 15.4 W – Luminaire Power: 18.8 W – Rated
- Temperature: 25°C to 35°C – Ambient Temperature: 50°C to 139.2°C –
- Module Designation: 2x LED-0776/930
- Color Temperature: 3000 K – Colour
- Rendering Index (CRI): > 90 – Module Luminous Flux: 2520
- lm – Luminaire Luminous Flux: 1590 lm – Luminaire Luminous
- Efficiency: 84.6 lm/W
Product Usage Instructions
Safety:
The installation and operation of this luminaire must comply with national
safety regulations.
Installation and commissioning should only be performed by a qualified
electrician. The manufacturer is not liable for any damage caused by improper
use or installation.
Any modifications made to the luminaire should be carried out by the
responsible person.
Overvoltage Protection:
The electronic components in the luminaire are protected against overvoltage
according to DIN EN 61547.
For additional protection against transients, it is recommended to use
separate overvoltage protection components available on the manufacturer’s
website.
Replacement of the LED Module:
The designation of the LED module is indicated on a label inside the
luminaire.
BEGA replacement modules have the same light color and output as the original
modules.
Qualified individuals can replace the module using standard tools.
Before replacing the module, disconnect the system and open the luminaire.
Follow the installation instructions provided for the LED module.
If the glass is defective, it should be replaced.
Close the luminaire after completing the replacement.
Note: If mounting the luminaire on a metallic, electroconductive surface,
ensure that the mounting surface is connected conductively to the earth
conductor of the luminaire. Maintain a distance of 340 mm above the luminaire
when replacing the LED module, mounting, or dismantling the glass.
Wall luminaire for indoor use
Application
Free-radiating wall luminaire · indoor luminaire made of hand-blown opal
glass, satin matt, and metal housing. The character of the three-ply opal
glass creates a smooth and uniform light distribution in the room.
Product Description
- Glass holder made of matt brushed aluminum Hand-blown opal glass, satin matt
- 2 mounting holes ø 6 mm
- Distance apart 192 mm
- Connection terminal 2.5
- Earth conductor connection
- Installation surface 412 x 35 mm
- 2-pole connecting terminal for digital control
LED power supply unit
- 220-240 V x 0/50-60 Hz
- DC 176-264 V
- DALI-controllable
- Number of DALI addresses: 1
- Basic insulation is provided between the mains and control cables
BEGA Thermal Control
Temporary thermal regulation to protect temperature-sensitive components
without switching off the luminaire
- Safety class I
- r – Safety mark
- c – Conformity mark
- Weight: 1.8 kg
This product contains light sources of energy efficiency class(es) C, D
Safety
The installation and operation of this luminaire are subject to national
safety regulations. Installation and commissioning may only be carried out by
a qualified electrician. The manufacturer accepts no liability for damage
caused by improper use or installation. If subsequent modifications are made
to the luminaire, the person responsible for these modifications shall be
considered the manufacturer.
Overvoltage protection
The electronic components installed in the luminaire are protected against
overvoltage in accordance with DIN EN 61547. To achieve additional protection
against e. g. transients, etc. we recommend separate overvoltage protection
components.
You can find them on our website at www.bega.com.
Lamp
- Module connected wattage 15.4 W
- Luminaire connected wattage 18.8 W
- Rated temperature ta = 25 °C
- Ambient temperature ta max = 35 °C 50 139.2 K3
- Module designation 2x LED-0776/930
- Color temperature 3000 K
- Color rendering index CRI > 90
- Module luminous flux 2520 lm
- Luminaire luminous flux 1590 lm
- Luminaire luminous efficiency 84,6 lm / W
- 50 139.2 K4
- Module designation 2x LED-0776/940
- Color temperature 4000 K
- Color rendering index CRI > 90
- Module luminous flux 2670 lm
- Luminaire luminous flux 1657 lm
- Luminaire luminous efficiency 88,1 lm / W
Please note
If the luminaire is to be mounted onto a metallic, electroconductive surface,
it is mandatory to make sure that the mounting surface is connected
conductively to the earth conductor of the luminaire! For replacing the LED
module, mounting, and dismantling of the glass please keep a distance of 340
mm above the luminaire.
Installation
LED are high-quality electronic components! Please avoid touching the light output opening of the LED directly during installation or relamping. Make an earth conductor connection to the earthing screw (1) on the reverse side of the glass holder. Make electrical connections to the terminals marked (L) and (N). For digital control please use the connecting terminal DA, DA. In case this terminal is not used the luminaire will be operated at full light output. Slide the synthetic diffuser out of the LED supporting section. The mounting of the glass holder requires two holes drilled into the wall. Fix the glass holder with enclosed or any other suitable fixing material onto the mounting surface. Note the position of the application “arrow down”. Insert the synthetic diffuser by sliding it into the LED supporting section until the stop. Place glass with its opening over the LED module. The magnet fixes the glass on the glass holder. The mounting of the glass holder requires two holes drilled into the wall. Fix the glass holder with enclosed or any other suitable fixing material onto the mounting surface. Note the position of the application “arrow down”. Insert the synthetic diffuser by sliding it into the LED supporting section until the stop. Place glass with its opening over the LED module. The magnet fixes the glass on the glass holder.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>