BEGA 50064.1 Wall Luminaire Instruction Manual

Table of Contents

Safety: The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning should be done by a qualified electrician. The manufacturer does not accept liability for damage caused by improper use or installation.
Overvoltage Protection: The electronic components installed in the luminaire are protected against overvoltage according to DIN EN 61547. For additional protection against transients, it is recommended to use separate overvoltage protection components.
Lamp Information:
- Module Connected Wattage: 16.4 W
- Luminaire Connected Wattage: 19.3 W
- Rated Temperature: ta = 25°C to 40°C
- Ambient Temperature: ta max = 50°C
Module Information:
- Module Designation: 50 064.1 K3
- Colour Temperature: 3000 K
- Colour Rendering Index (CRI): CRI > 90
- Module Luminous Flux: 3290 lm
- Luminaire Luminous Flux: 1174 lm
- Luminaire Luminous Efficiency: 60.8 lm / W
Spares: DEV-0312/500 LED power supply unit, LED-0275/930 LED module 3000 K

Ensure that the luminaire is installed and operated in accordance with national safety regulations. If you are not a qualified electrician, hire one for the installation and commissioning.
Consider using separate overvoltage protection components to provide additional protection against transients.
For the lamp, connect the module with a wattage of 16.4 W and the luminaire with a wattage of 19.3 W.
The rated temperature for operation is between 25°C and 40°C. The maximum ambient temperature should not exceed 50°C.
The module designation is 50 064.1 K3 with a colour temperature of 3000 K.
The colour rendering index (CRI) is greater than 90, indicating high-quality colour representation.
The module has a luminous flux of 3290 lm, while the luminaire has a luminous flux of 1174 lm.
The luminaire has a luminous efficiency of 60.8 lm / W, indicating its energy efficiency.
If any parts need replacement, use the DEV-0312/500 LED power supply unit and the LED-0275/930 LED module with a colour temperature of 3000 K.

BEGA-50064.1-Wall-Luminaire-FIG-1

Application

Wall luminaire · indoor luminaire with integrated power supply unit for many lighting tasks in interior applications.
The light emits upwards and downwards.

Luminaire made of aluminium alloy
Finish Colour white
Crystal glass with white matt finish
2 elongated fixing holes
Width 4.5 mm · 84 mm spacing
2 cable entries for through-wiring of mains supply cable ø 7-10.5 mm, max. 5 G 1.5@
Connection terminal 2.5@
Earth conductor connection
2-pole connecting terminal for digital control
BEGA Ultimate Driver®
LED power supply unit
220-240 V x 0/50-60 Hz
DC 176-276 V
DALI-controllable
Number of DALI addresses: 1
Basic insulation is provided between the mains and control cables
BEGA Thermal Control®
Temporary thermal regulation to protect temperature-sensitive components without switching off the luminaire

Safety class I

This product contains light sources of energy efficiency class(es) D

The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e. g. transients, etc. we recommend separate overvoltage protection components.
You can find them on our website at www.bega.com.

Lamp

50 064.1 K3

LED are high-quality electronic components! Please avoid touching the light output opening of the LED directly during installation or relamping.
Undo the screws and lift off the luminaire top. Lead the mains supply cable through the cable entry of the luminaire base.
Note position of application of the luminaire “arrow down”.
Fix luminaire base with enclosed or any other suitable fixing material onto the mounting surface.
Be sure to use the gasket rings supplied. Make earth conductor connection.
Push silicone sleeves over the lines and make electrical connection.
For digital control please use the connecting terminal DA, DA.
In case this terminal is not used the luminaire will be operated at full light output.
Make earth conductor connection between the luminaire top and luminaire base (plug connection).
Install the luminaire top, press on and manually tighten screws evenly.

The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted.
The module can be replaced by qualified persons using standard tools.
Disconnect the system and open the luminaire. Please follow the installation instructions for the LED module.
Inspect and, if necessary, replace the luminaire gaskets.
Defective glass must be replaced.
Close the luminaire.

Spares