universal douglas LVLBP34-90 LED Linear Pendant Light Installation Guide

June 3, 2024
universal douglas

universal - logo LVLBP34-90 LED Linear Pendant Light
Installation Guide

LED LINEAR PENDANTLIGHT

IMPORTANT SAFETY INSTRUCATION

Read this installation guide prior to attempting installation.Always turn OFF the main power before starting your installation. Consult a qualified electrician before installation. Installation should be carried out by a qualified eletrician.
During installation, basic safety precautions should always be followed, including the following listed.

  1. Do not install the lighting system in a wet location.
  2. Ensure the appropriate connectors match the luminaire fixture
  3. Do not install any part of the luminaire less than 5 feet above the floor.
  4. Do not install any luminaire assembly closer than 5 inches from any window treatments,i.e.,curtain, blinds or any similar combustible type material.
  5. Do not attempt to energize anything other than the luminaire fixtures.
  6. To reduce the risk of fire and electric shock,do not attempt to connect to power tools, extension cords, appliances, or the like, to the track.
  7. Maintenance of the luminaires should be performed by person(s) familiar with the luminaires construction and any hazards involved. regular fixture maintenance programs are recommended.
  8. Do not exceed the nominal supply voltage or amperage ratings.
  9. Turn the power OFF at the fuse or circuit breaker box before doing any installation or maintenance activities.
  10. Wear rubber soled shoes and work on a sturdy wooden or non-conductive ladder.
  11. The lighting product must be mounted in locations and at heights in compliance with the National Electrical Code and with local building codes. Installing contrary to instruction may cause unsafe conditions.
  12. To avoid hazards to children, take accountability for all parts and dispose all packing materials properly.
  13. It may be necessary to clan the refractor / lens.Frequency of cleaning will depend on ambient dirt level and minimum light output which is acceptable to the user.  Refractor / lens should be washed in a solution of warm water and any mild, non-abrasive household detergent, rinsed with clean water and wiped dry. Should optical  assembly become dirty on the inside, wipe refractor / lens and clean in above manner, replacing damaged gaskets as necessary.
  14. Call the Technical Support department about any installation questions.
  15. Do not install a damaged product. This luminaire has been properly packed so that no parts should have been damaged during transit. Inspect to confirm.Any part  damaged or broken during or after assembly should be replaced.
  16. These instructions do no purport to cover all details or variations in equipment nor to provide every possible contingency to meet in connection with installation,  operation or maintenance.Should further information be desired or particular problems arise,not covered sufficiently for the purchaser’s or owner’s purposes, please contact the Technical Team.

LVLBP34-90 LED Linear Pendant Light

CATION
This equipmen is intended to be installed only by qualified personnel.
The installation must be made in accordance with the current edition of the National Electrical Code (NEC) and all applicable state and local building codes. The final  installation must be approved by the appropriate, qualified electrical / building inspector(s). Improper installation may result in a fire or electrical hazard. Ensure the electrical power to the circuit has been disconnected before installing the electrical system

WARNING

  • Risk of fire. Most dwellings built before 1985 have supply wire rated at 60°
  • Consult a qualified electrician before installation.
  • Properly ground electrical enclosure.
  • To prevent wiring damage or abrasion, do not expose wiring to edges of sheet meal or other sharp objects.
  • Use only UL approved wire input/output connections.Minimum size 18 AWG or 14AWG if there are any continuous runs.
  • If the fixtures are connected in a continuous run, do not exceed allowable number of fixtures in series/power in continuous runs.
  • Inrush currents must be taken in account by the electricians to account for proper circuit design.

TOOL
A1) Rope Suspension Installation

universal douglas LVLBP34 90 LED Linear Pendant Light

Drill a hole of 5.0mm in diameter at the location required for installation. Then install the plastic anchor to the hole with hammer.

No. Size A(in) B(in)
1 2FT 22.21 /
2 4FT 45.83 /
3 6FT 69.45 /
4 8FT 46.54 46.5

universal douglas LVLBP34 90 LED Linear Pendant Light - fig
1

Insert PA430 Screws into the screw holder and then drill into the plastic anchor.universal douglas LVLBP34 90 LED Linear Pendant Light -
fig2Lock the steel wire rope pedestal to the ends plates with PM48 screws.universal douglas LVLBP34 90 LED Linear
Pendant Light - fig3Press down the inner hole of the steel wire rope pedestal, let the steel wire rope go through the hole.universal douglas LVLBP34 90 LED Linear Pendant Light -
fig4

Connect L,N,GND,DIM+ and DIM- of AC input wire to L,N,GND, DIM+and DIM- respectively of AC terminal.universal douglas LVLBP34 90 LED Linear Pendant
Light - fig5Press the to pend of the steel wire rope pedestal to adjust the steel wire rope,and then finish the installation.

A2) Canopy Suspension Installation

universal douglas LVLBP34 90 LED Linear Pendant Light -
fig6

Drill a hole of 5.0mm in diameter as shown in the figure at the location required for installation. Then hammer the plastic anchor into the hole.

N0. 1 Size A(in) B(in) C(in) D(in) E(in)
1 2ft 3.346 18.9 3.35 / /
2 4ft 3.346 42.5 3.35 / /
3 6ft 3.346 66.1 3.35 / /
4 8ft 3.346 43.2 3.35 43.2 3.35

universal douglas LVLBP34 90 LED Linear Pendant Light -
fig7

Insert PA4*30 screws into the M type mounting bracket and then drill into the plastic anchor.universal douglas LVLBP34 90 LED Linear Pendant Light -
fig8

Lock the steel wire rope pedestal to the ends plates with PM4*8 Screws.

universal douglas LVLBP34 90 LED Linear Pendant Light -
fig9Press down the inner hole of the steel wire rope pedestal, let the steel wire rope go through the hole.universal douglas LVLBP34 90 LED Linear Pendant Light -
fig10The thread locker passes through the canopy and is fixed with a screw nut, and the waterproof connector passes through the gasket and the canopy, and is fixed with a screw nutuniversal
douglas LVLBP34 90 LED Linear Pendant Light - fig11Press the steel wire rope holder as shown in the figure, and then insert the stainless steel wire into the inner hole of the steel wire rope holder; The mounting height of the  lamp could be adjusted by this steel wire rope holder.universal douglas LVLBP34 90 LED Linear Pendant Light -
fig13Pass the AC into the waterproof connector, fix the AC wire with a screw cap, connect the L pole to the black wire, the N pole to the white wire, the GND to the green wire,  the DIM+ pole to the purple wire, and the DIM- pole to the pink wire

universal douglas LVLBP34 90 LED Linear Pendant Light -
fig14Adjust the length of the AC input cable, align the side hole of the canopy and the M mounting bracket as shown in the figure, then tighten the screw.universal douglas LVLBP34 90 LED
Linear Pendant Light - fig15

B.Linkable Instruction
Note:Only available for Linkable Products.

universal douglas LVLBP34 90 LED Linear Pendant Light -
fig16

Measure the ceiling , make down the position for lineae1, install the first Linear Light to the ceiling as instruction of A Rope Suspension Installation.

No. Size A(in) B(in) C(in) D(in) Remark
1 2FT 22.920 23.630 22.920 / 3pcs linkable diagrammatic drawing
2 4FT 46.540 47.250 46.540 / 3pcs linkable diagrammatic drawing
3 6FT 70.160 70.870 70.160 / 3pcs linkable diagrammatic drawing
4 8FT 46.540 47.250 47.250 46.540 2pcs linkable diagrammatic drawing

universal douglas LVLBP34 90 LED Linear Pendant Light -
fig17Install Linear 1, then connect AC line; remove one end cap as show on (2-b)universal douglas LVLBP34 90 LED
Linear Pendant Light - fig18

Lift up the up-light module as the picture shows.universal douglas LVLBP34
90 LED Linear Pendant Light - fig19Insert the linkable bracket into the Linear1,connect with buckle inside the Linear1,take out the inside linkable wire. ( Five color)universal
douglas LVLBP34 90 LED Linear Pendant Light - fig20Insert the Linear Light as Step 2 and adjust the steel wire rope in the same height. Then Move out two end caps of Linear2,lift up the up light module, disconnect the AC  wire. keep the female plug to the side endsuniversal douglas LVLBP34 90 LED Linear Pendant Light -
fig21Connect the male plug of Linear 1 and female plug of Linear2, insert the bracket to the Linear 2 make them seamless linkable together.universal douglas LVLBP34 90 LED Linear Pendant
Light - fig22Check the status after linked make sure no any gap between two linears.

universal douglas LVLBP34 90 LED Linear Pendant Light -
fig23Make sure the male and female plugs have been connected well,press down the uplight module, put it back to the top of Linear1 and Linear2universal douglas LVLBP34 90 LED Linear
Pendant Light - fig24

Install the Linear Light 3,4,5,6 and7 as above method,keep one main input cord on one side for wiring andg rounding Adjust the steel wrie rope inthe same height. Then  finish the installation.

NOTE:LED LINEAR CAN BE GAPLESS LINKABLE TOGETHER AS NEEDED, ( if you order to use 18# cord,More Links can be Customized.)

Max. linkable Quantity (Unit:PC) Linkable fixtures Qty need t o meet the below two conditions:
1)N<7pcs
2) Input voltage = 120V , NP<420W
Input voltage =347V , N
P<960W
Note: N = Qty of linkable fixtures,
P = Wattage per fixture

C. Wall Mount

universal douglas LVLBP34 90 LED Linear Pendant Light - . Wall
Mount

Installation Kits

universal douglas LVLBP34 90 LED Linear Pendant Light - Installation
Kits

1 C Wall-mount Bracket 1PC
2 Square Decorative 1 PC
3 L support 2PCS
4 Plastic Anchor 4PCS
5 Cross head tapping 4PCS
6 Hand screw 4PCS
7 Screw 1PC
8 End cap 2PCS
9 Linkable braket 1 PC

universal douglas LVLBP34 90 LED Linear Pendant Light -
fig26Drill Hole on the wall based on the Length of the Fixture, Fix the plastic anchor in the hole and fix the Wall Mount Bracket on the Wall.universal douglas LVLBP34 90 LED Linear Pendant
Light - fig27

Push the L support bracket into the wall mount bracket as followed. universal douglas LVLBP34 90 LED Linear Pendant Light -
fig28Connect L, N, GND, DIM+ and DIM- of AC input wire to L, N, GND, DIM+ and DIM- respectively of AC wire.
Get the linear light install into the wall mount bracket as followed picture. Using the hand screw to secure the linear light.

universal douglas LVLBP34 90 LED Linear Pendant Light -
fig29Connect the quick connector between the linear light and connector from the AC power wire. After then, put it into the linear body.

Linkable fixtures Qty need to meet the below two conditions:
1)N<7pcs.
2)Input voltage = 120V , NP<420W
Input voltage = 347V , N
P<960W
Note: N = Qty of linkable fixtures,
P= Wattage per fixture.

universal douglas LVLBP34 90 LED Linear Pendant Light -
fig30

Linkable braket insert into one fixture , connect the male and female connector, the other part of linkable braket insert into the other fixuture. Then the fixture fixed on the wall mounted kit.

Install the end caps, the connector wire must get through the correct place on the end caps as followed picture.

Turn on the light.

D. Install MAS & Sensor

universal douglas LVLBP34 90 LED Linear Pendant Light -
Sensoruniversal douglas LVLBP34 90
LED Linear Pendant Light - Sensor 1

  1. Insert the purple cable into 1# hole, pink cable for “-“, red cable for “+”;
  2. Connect the male terminals to female from the lighting fixture;
  3. Connect the red cable to red cable from lighting fixture with nipple connector;
  4. Fix the sensor to MAS, and then fix the MAS to the lighting fixture by screws.

universal douglas LVLBP34 90 LED Linear Pendant Light -
Sensor3

  1. Fix the pedestal with Aircraft ropes to the lighting fixture by M4*8mm Screws;
  2. Adjust the length of the suspending ropes, make balance of the lighting fixture.

universal douglas LVLBP34 90 LED Linear Pendant Light -
Sensor4universal douglas LVLBP34 90
LED Linear Pendant Light - Senso6

  1. Connect the AC Input power cable to the lighting fixture: 3-wiring terminals, male to female.
  2. Fix the AC input power cable to the stuckable hole on the lighting fixture.
  3. Put the Upper Lighting modular back, and fix it to the lighting fixture.

universal douglas LVLBP34 90 LED Linear Pendant Light -
Senso5universal -
logowww.universaldouglas.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

universal douglas User Manuals

Related Manuals