universal douglas 4 Foot Vapor Tight Slim (VTLS) Instruction Manual

: June 3, 2024
: universal douglas

Table of Contents

universal douglas 4 Foot Vapor Tight Slim (VTLS)
SAFETY WARNINGS
- IMPORTANT SAFETY INFORMATION
INSTALLATION
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

universal douglas 4 Foot Vapor Tight Slim (VTLS)

$universal-douglas-4-Foot-Vapor-Tight-Slim -VTLS\)-product$

SAFETY WARNINGS

IMPORTANT SAFETY INFORMATION

Before you begin.
Read these instructions completelycompletely&carefully.

Warning

Risk of electrical shock. Disconnect power before servicing or installing the luminaire.
Risk of injury or damage. The luminaire will fall if not installed properly. Follow installation instructions. NEC and local codes and best trade knowledge.
Risk of injury. Wear safety glasses and gloves during installation and servicing.

Follow the information on the label & instructions regarding installation near combustible materials, insulation, and building materials & in Dry or Wet locations. Do not install in areas exposed to combustible vapors or gases. This product must be installed by a person familiar with the construction and operation of the product and the hazards involved, in accordance with the applicable installation. Be sure to ground the product to avoid potential electrical shock or another potential hazard. Use of accessory equipment not recommended by the manufacturer or installed inconsistent with instructions may cause an unsafe condition. Do not completely or partially block light emerging from the product, as this could cause an unsafe condition. Do not allow other items to come into contact with the product, as this may cause an unsafe condition.

WARNING: This product may contain chemicals known to the State of California to cause cancer, birth defects and other reproductive harm. Thoroughly wash your hands after installing, servicing, handling, cleaning, or otherwise touching this product. This device complies with FCC CFR Title 47 Part 15, Class A requirements for EMI/RF.

INSTALLATION

Step 1: Inspect Product

Inspect the product upon receipt and notify the delivery carrier of any damage that may have occurred during shipment. Confirm the product ordered matches the product received by comparing the catalog number listed on the packing slip to the carton label.

Step 2: Install Mounting Brackets

ldentify locations and securely attach mounting brackets to the mounting surface. Use two (2) brackets for 4′ units and four 4) brackets for 8′ units. Mounting brackets engage the housing at any point along its length not obstructed by latches. Mount brackets evenly to span at least 60% of the length of the housing.

Step3: Remove Lens

Disengage latches to release lens. Remove and set aside in a protected location.

Step 4: Mount Housing

Insert one side of the housing into mounting brackets, taking care to assure that bracket engages the housing lens retention lip without distorting gasket. Rotate the housing up and press other side of the mounting brackets to similarly engage on the other side until the bracket clicks into place. Verify that the housing is fully supported.

Step 5: Prepare Luminaire for Wiring

Release LED gear tray by squeezing white plastic mounting clips (2 for 4′, 4 for 8′) for 2-LED-row models or by removing nuts (2 for 4′, 4 for 8′) for 1 -LED-row models. LED gear tray will suspend from plastic tethers during housing installation.

Step 6: Suspend LED Gear Tray

Following release of LED gear tray in Step 5, the gear tray will suspend from plastic tethers during housing installation. Remove end plug(s) to accommodate wiring connections as required.

Step 7: Bring in Power

Bring wiring into housing as required using Universal Douglas VTA-DCFIT-1/2 die cast aluminum fitting assembly for ” rigid conduit connections (sold separately).

NOTE: For an improved water tight seal, apply silicone sealant to both sides of O-ring as shown.

Step 8: Make Electrical Connections

Make electrical connections to the LED driver. Connect Line (Black), Neutral (white) and Ground (Green) connections and insulate to 600 VAC. Assure proper grounding.

Step 9: Reinstall LED Gear Tray