universal douglas CDL06-13WS935S-U LED Downlight Instructions
- June 3, 2024
- universal douglas
Table of Contents
universal douglas CDL06-13WS935S-U LED Downlight
Product Information
| Model No. | Size | D1 | D2 | H | Cut-out |
|---|---|---|---|---|---|
| Min. | Max. | ||||
| CDL06-13WS935S-U | 6″ | 8 – 7 / 16 ” | 5 – 7 / 8 ” | 4 – 7 / 16 ” | φ6 – 1 / 8 ” |
φ7 – 3 / 1 6 ”
CDL08-23WS935S-U| 8″| 10 – 1 / 16 ”| 7 – 3 / 8 ”| 4 – 3 / 4 ”| φ7-9/16”| φ8 –
1 1 / 1 6 ”
CDL10-29WS935S-U| 10″| 11 – 3 / 8 ”| 8 – 11 / 16 ”| 5 – 1 / 4 ”| φ8 – 7 / 8 ”|
φ 1 0 ”
Universal Douglas’ s switchable round LED recessed downlight fixtures allow
for selecting between three power levels and three CCT settings to match a
wide range of applications. The power level and CCT selector switches are on
the backside of the fixture and should be set prior to installation
INSTALLATION
Note : Class 2 driver, risk of electric shock, The junction box needs to connect to the “ground wire”;
- Step 1: Make sure the POWER is Turned OFF when installing the products:
- Step 2: Select the CCT and Lumen level with the dip switches
- Step 3: Attach the carabiner safety clip to the existing fixture housing
- Step 4: Insert lamp conduit into the J-box and wire to power source (black to hot, white to neutral, violet to 0-10V dimming positive, gray to 0-10V dimming negative) Reattach J-box cover when done;
- Step 5: Squeeze the two housing clips so they are in an upright position and insert lamp into opening
- Step 6 : Once lamp is inside the opening, release the housing clips and continue pushing lamp into opening until securely fixed an ush with ceiling
- Step 7: Restore power at the source and the installation is complete.
WARNING :
- First please read all product labels and instruction before installing fixture. Risk of fire or electric shock. LED Retrofit Kit installation requires knowledge if luminaires electrical systems.
- Installation should be performed only by a qualified electrician in accordance with the National
- Electrical Code and relevant local code. Install this kit only in the luminaires that have the construction features and dimensions shown in the photographs and/or drawings.
- To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or another sharp object.
- Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation. The recessed luminaire will be exposed to damp or dry locations.
INSTALLATION SHOULD ONLY BE PERFORMED AFTER POWER TO THE FIXTURE HAS BEEN DISCONNECTED. THIS RETROFIT KIT IS ACCEPTED AS A COMPONENT OF A SUITABILITY OF THE COMBINATION SHALL BE DETERMINED BY AUTHORITIES HAVING JURISDICTION.
FCC
Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interferencein a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harm- ful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/ TV technician for help.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>