HDMI Extender ER2604EXIP OVER IP 120M User Manual
- June 10, 2024
- HDMI EXTENDER
Table of Contents
HDMI Extender ER2604EXIP OVER IP 120M
Product Information
The HDMI extender allows users to extend the transmission length of the HDMI
visual and audio signal up to 120m (394 ft) with a single network cable. The
product supports IR signal transmission, allowing users to control media
playback of the signal source device at the display location. The ER2604EXIP
model comes with RJ45 signal output and input.
It is recommended that Gigabit Ethernet switches be used in LAN. Fast Ethernet
switches (100Mbps) and Gigabit Ethernet switches (1000Mbps) cannot be mixed
and used in cascade. The product is HDMI1.3 compatible with HDCP1.4 protection
against lightning, surge, and ESD.
Product Usage Instructions
- Connect one end of the HDMI cable to the source device and the other end to the sender unit’s HDMI input port.
- Connect the sender unit’s RJ45 output port to the receiver unit’s RJ45 input port using a single network cable.
- Connect one end of the HDMI cable to the display unit and the other end to the receiver unit’s HDMI output port.
- If required, connect the IR transmitter and receiver cables to their respective ports on the sender and receiver units.
- Connect the power adapter to both sender and receiver units and plug them into a power outlet.
- Turn on the source device and the display device. The sender and receiver units will automatically detect the signal and establish a connection over the network cable.
Note: If you have multiple sets of extender units, it is recommended that you use a Gigabit Ethernet switch instead of cascading multiple Fast Ethernet switches or Gigabit Ethernet switches.
INTRODUCTION
HDMI extender, extends the transmit length of HDMI Visual/Audio up to 120m(394ft) with a single network cable. Supports IR signal transmission, to control media playback of the signal source device at the display location
Important Safety instructions
- Do not mix up the HDMI EXTENDER sender and HDMI EXTENDER receiver, and the IR blaster and IR receiver.
- Do not plug in/out the cables, when it is in use.
- Use DC SV power supply only. Make sure the specification matched if using 3rd party DC adapters.
Package Contents
Note : above accessory, content Is a regular package far a kit, If buy the HDNl extender TX or HDMI extender RX separately, the package contents would be different.
Installation Requirements
- HOM! source device(computer graphics card, DVD,PS3, HD monitoring equipment etc
- HDMI display devices like SDTV, HDTV, and projectors with an HDMI port.
- Network cables: UTP/STP CatSe/6 network cables, which follow the standard of!EEE-568B. Transmission length: CATS BOm/CATSE l00m/CAT6120m
Panel Description
HDMI EXTENDER TX (Sender)
- Reset
- HOM! Signal input
- JR signal output to connect with blaster extension cable
- Power input ( DCSV)
- Power Light
- Rj45 signal output
- Data transmission light
- Network link light
HDMI EXTENDER RX(Receiver)
- Reset
- HDMI signal output
- IR signal input to connect with IR receiver extension cable
- Power input ( DC5V)
- Power Light
- Ri45 signal intput
- Data transmission light
- Network link light
Installation Procedures
How to make a Cat5e/6 network cable
Follow the stanard of IEEE-568B:
- Orange/white
- Orange
- Green/white
- Blue
- Brown/white
- Blue/white
- Brown
- Green
Connections
- Point-to-Point connection: Up to 120 meters transmission distance over single CAT6.
- LAN Switch Cascade Connection: By using the LAN switch/router to realize unlimited extension.
- One-to-many Connection: By using network router/switch, one sender to several receivers, realize extender & splitter function.
Note : It is recommended that Gigabit Ethernet switches be used in LAN. Fast Ethernet switches (100Mbps) and Gigabit Ethernet switches (1000Mbps) can not be mixed-use in cascade.
IR User Guide
- IR blaster extension cable should plug-in the IR-out port of TX (Sender) of HDMI extender, and the IR receiver extension cable should plug-in the IR-out port of the RX (Receiver) of HDMI extender.
- The emitter of IR blaster should as close as possible to the IR receiver of the signal source device.
- Using the IR remote controller of the signal source device towards the IR receiver (connected to the RX of HDMI extender), to remote control source media playback.
FAQ
Q: TV display “Waiting for connection” ?
A: Please check if the power supply of TX (Sender) and switcher (if used) is
connected, and make sure connecting cable is firmly.
Q: TV display “Please check the TX input signal”?
- please check if there is a HDMI signal input of TX.
- Try to connect the signal source directly to display device to see if there is singal output from source device or change the signal source, HDMI wire and try again.
Q: Display not fluent, not stable?
- Please check the cable length between the TX to switch, the switch to the RX and the connection between each level is within the required range.
- Click the”reset”button on the TX/RX front panel, reset and reconnect.
Specification
Disclaimer
The product name and brand name may be registered trademark of related manutactures. ” and ®may be omitted on the user manual. The pictures in this user manual are just for reference. The terms HDMI,HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.We reserve the rights to make changes without further notice to a product or system described herein to improve reliability, function or design.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>