DELTA DORE 6351443 Pro Tywell Starter User Guide

: June 21, 2024
: DELTA DORE

Table of Contents

Product Instruction
Description
Ty well Pro installation
Troubleshooting Ty well Pro
Ty well Pro’s advanced features
Features
Technical specifications Tywell Pro
Technical specifi cations Tywell Control
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

**DELTA DORE 6351443 Pro Tywell Starter User Guide

**

Product Instruction

Included

Ty well Pro
Ethernet cable
Ty well Control
3 batteries 1,5V – AAA LR 03
Installation instructions / Important product information

Ty well Pro

Bio climatic manager
INFO
APPLICATION

Description

A. 230 V power supply terminal
B. Ethernet port
C. Configuration/Information/MAC address button
D. System status light
E. Remote antenna connection (optional)
F. USB output connection (optional)
Ty well Control
Wireless controller for shutter and heating control

**Description

A. Outside temperature
B. Weather service
C. Indoor temperature
D. Confi guration
E. Shutters menu
F. Set-point temperature
G. Low-consumption digital display
H. Absence mode
I.** Thermal menu

Ty well Pro installation

Ty well Pro must be installed on a DIN rail (35 mm) or in a consumer unit, or in a V D I unit. Only a qualified person should attempt to install the device.
Ty well Pro should be protected with a 2 A circuit breaker, which will also act as a power supply switch.
Avoid locations near power controllers (D H W contractor ty p ).

Switch off the 230 V power to your installation.
Connect your Ty well Pro :
Connect the Ethernet cable.
Then, connect the main power cables.
If you do not have internet access, you will need a Wi-Fi router to install the product.
_While the system does not need internet access to work, it is recommended for best results.

_ The 230 V power supply wires should be stripped to 8 mm.
To do this, use the case to help as shown opposite.

Restore the power to the installation.
Download the Tydom app.

Tydom

  *  **Depending on your unit :** connect to Google Play or the App Store.
  * Find and download the free «Tydom» application.

Turn on your smartphone or tablet Wi-Fi and connect to the same local network used by your Tywell Pro.
If you have a router in the installation, turn off your phone’s data connection.
Set up the Tydom application.
- Make a note of the last 6 characters of your Tywell Pro’s MAC address (found on the front).
- Connect to the app and follow the process.

Remote antenna

The wireless range can be adjusted to suit the installation.

Some installations will require a remote antenna compatible with X3D and Zigbee (available as an accessory).

This is advised, for example, for an installation in a metal unit or near a metal mass.

Troubleshooting Ty well Pro

Light	System status
Flashing white	System accessible locally and remotely, user logged in.
Steady white	System accessible locally and remotely
Flashing orange	System accessible locally, user logged in
Steady orange	System accessible locally
Steady red	No allocated IP address
5 red flashes	Thermal safety function. Leave a clear space around the Ty well

Pro in the event that it starts to heat up.

Ty well Pro’s advanced features

These are the features accessible depending how long you push your Tywell Pro’s configuration button (F) for.

A : Secure connection and viewing of connection status
Briefly press the button.
The light will flash for 10 seconds.

Flashing yellow	Static IP mode
Flashing blue	DHCP mode
Flashing blue (3x)	DHCP in progress. Check that the DHCP is activated on the

HUB.
Flashing red| No network connection. Check the Ethernet connection.

B : Change from static IP to DHCP
Press the button for 3 seconds until the pink light flashes slowly. Release.
C : Reset to factory settings
Press the button for 30 seconds until the light stops flashing. Release.

Press the button for 30 seconds until the light stops flashing. Release.

System status|

D H C P mode
Clear product associations

Ty well Control installation
This product should be installed in a location with a temperature representative of the room needing regulation.
The recommended height is around 1.5 m and the product should be away from heat sources (fi replaces, sunlight, etc.) and draughts (windows, doors, etc.).
To avoid unwanted air movements that would distort the sensor’s temperature measurements, the wire entry into the fl ush-mounted box must be plugged (with mastic, glass wool, etc.).

IMPORTANT :
Do not install the controller on a wall in contact with the outside or in an unheated room (e.g. garage, etc.).

Ty well Control mounting
3 x 1,5V – AAA LR03

Pairing Tywell Control with a thermal receiver and/or a Tywell Pro

To pair an RF6050, RF6050+ or RF6700FP receiver, follow the steps below.
For all other products, please refer to their instructions.

Step 1: Pair Tywell Control with a thermal receiver and/or a Tywell Pro

If Ty well Control has never been paired (initial commissioning), the screen displays:

Select «Tywell Pro» or «Thermal Receiver», depending on the product to be paired.
Confirm, then follow the instructions.

  * If pairing has already been partially carried out, access the pairing menu as follows:  

  * Select «Tywell Pro» or «Thermal Receiver», depending on the product to be paired. Confirm, then follow the instructions.

Step 2: Link the thermal receiver with the Tywell Control using the Tydom application

Follow the instructions to confirm the link between the thermal receiver and the Ty well Control using the Tydom application.

In the Tydom application, select your installation, then select:

My devices
Select the relevant Tywell Control
Activate the «Advanced options» menu
Receiver linked: «None»
Click on «None» and follow the instructions.

Features

Tywell Control features
The Tywell Control operates devices, optimises energy use and makes a space more comfortable.

Centralised shutter control.
Shutter autopilot
Automatic shutter management notifications
Heating and air conditioning management (where there is a heating receiver)
Absence mode

Setting up shutter autopilot
Associating shutters
Associate shutters with the Tydom application.
Go to the «My devices» page of your installation, select > Add a device > Shutters > Select your device, then follow the instructions.

Automatic opening
The shutters will automatically open in the morning and close in the evening based on sunrise and sunset times.
Heat protection
Heat protection automatically manages shutters to keep your home cool. For optimum autopilot results with shutters, a Tysense Sun sensor and a Tysense Thermo outdoor temperature sensor are recommended.

In the Tydom application, select:
Tysense Sun: Add a device > Sensors > Tysense Sun, then follow the instructions.
Tysense Thermo: Add a device > Sensors > Tysense
Thermo, then follow the instructions.
The sensors can be replaced by weather service data from the Tydom application as long as the Tywell Pro is connected to the internet.

Create passive zones
A passive zone is a group of shutters that react to the same indoor temperature and sun data.
In the Tydom application, select:

Shutters autopilot > Set heat protection > Your zones, then follow the instructions to create the passive zone.
If the installation only has a single Tywell Control and a single sun sensor (or weather service data), create a single passive zone.
If the installation has multiple Tywell Controls and/or multiple sun sensors, you can create multiple passive zones.
All shutters on the same side and in the same room should be in the same passive zone.
Select the Tywell Control (measures indoor temperature) and the sun sensor or weather service.
Select the shutters to automatically operate for each zone.
How to activate shutter autopilot
Activate automatic opening and heat protection using the application or via the Tywell Control.
North-facing shutters do not need to be on autopilot.