DELTA DORE 2705327 2705327 Tydom Pro Box Instruction Manual
- June 12, 2024
- DELTA DORE
Table of Contents
Tydom Pro
Smart Home hub
2705327 2705327 Tydom Pro Box
The connection quality of the product may be affected by different modifications
of the IP architecture on which it operates.
These modifications can be, but are not limited to, a change of hardware, a
software update or configuration, work conducted on your operator’s equipment
or any other multimedia equipment such as tablets, smartphones, etc.
IOS is a Cisco trademark or registered trademark in the United States and in
other countries, and is used under licence. AndroidTM and Google Play are
Google LLC registered trademarks.
Wi-FiTM is a trademark registered by Wi-Fi Alliance.
Because of changes in standards and equipment, the characteristics given in
the text and the illustrations in this document are not binding unless
confirmed.
Presentation
Box contents
A. Tydom Pro
B. Ethernet cable
C. Important Product Information
Description
D. 230 V power supply terminal
E. Ethernet port
F. Configuration/Information/MAC address button
G. System status light
H. Remote antenna connection (optional)
I . USB port connection (optional)
Installation
Tydom Pro must be installed on a DIN rail, either within a consumer unit, or
in a VDI cabinet.
The equipment must be installed by a suitably qualified person.
Tydom Pro must be protected by a 2A circuit breaker,
which will also serve as a power switch.
Avoid proximity with power controls
(of the type used for domestic hot water contactors)
❶ Disconnect your installation’s 230V power supply.
❷ Connect your Tydom Pro :
- connect the Ethernet cable (B).
- then, connect the mains power line.
The 230 V power line must be stripped back to a length of 8 mm.
To do so, you can make use of the design of the casing as shown below.
❸ Restore the power to the installation.
❷ Download the Tydom app.
– Log in to either the Google Play or App Store, depending on your device.
– Search for and download the free «Tydom» app.
|
---|---
|
❸ Activate the Wi-Fi connection on your smartphone or tablet , and connect to
the same local network as your Tydom Pro.
❹ Configure the Tydom app.
– Note the last 6 characters of your Tydom Home’s MAC address (stated on the
front).
– Log in to the app and follow the instructions.
Remote antenna Some installation cases will require the use of a remote
antenna (available as an accessory)
The radio range can be adjusted based on the installation conditions.
This is advised, for example, in the case of installation in a metallic
cabinet or in proximity to a metallic mass.
Help
| LED | System status |
|---|---|
| Flashing white | System accessible locally and remotely, user connected |
| Steady white | System accessible locally and remotely |
| Flashing orange | System accessible locally, user connected |
| Steady Orange | System accessible locally |
| Steady Red | No IP address allocated |
| 5 red flashes | Thermal safety mechanism. |
Leave a clear space around the Tydom Pro in the event that it starts to heat up.
Advanced functions
Below are the functions accessible depending on how long the button on the
back of your Tydom Home is pressed.
A Secure connection and viewing connection status
Briefly press the button. LED displays for 10 seconds.
| Flashing yellow | Static IP mode |
|---|---|
| Flashing blue | DHCP mode |
| Flashing blue (3x) | DHCP in progress Check the DHCP |
activation on the router
Flashing red| No network connection Check
the Ethernet link
B Change from static IP to DHCP
Press the button for 3 seconds until the pink LED flashes slowly. Release.
C Reset to factory settings
Press the button for 30 seconds until the LED stops flashing. Release.
System status| – DHCP mode
– Clear product associations
Technical specifications
| 230V, 50/60 Hz power supplyClass II insulati on
---|---
| X3D transmission frequency: 868.7 MHz to 879.2 MHz
Maximum wireless power < 10mW – Category 2 receiver
Zigbee transmission frequency: 2.4 GHz to 2.4835 GHz
| Maximum consumpti on (without USB connecti on): 1,1 W
| -20°C / +70°C
| -10°C / +40°C
IP
| IP 30
| 4-module unit, height = 53 mm
Installati on in an environment with normal polluti on levels
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>