DELTA DORE Tybox 5701FP Pilot Wire Thermostat User Guide
- June 10, 2024
- DELTA DORE
Table of Contents
DELTA DORE Tybox 5701FP Pilot Wire Thermostat
Product Information: Tybox 5701FP – 5702FP – RF6700FP
The Tybox 5701FP, 5702FP, and RF6700FP are products manufactured by Delta Dore. Tybox 5701FP and 5702FP are wireless programmable thermostats that control the temperature of your heating system. The RF6700FP is a receiver that is used to connect the thermostat to the heating system. These products use radio frequency communication and have a range of up to 300 meters. They are compatible with both 115V and 230V systems. The Tybox 5701FP requires two LR03 – AAA alkaline batteries, while the RF6700FP runs on a 230V~ power supply. The Tybox 5702FP can be powered by either two AAA batteries or the main power supply.
Product Usage Instructions
Step 1: Make sure that your heating system is in automatic mode (AUTO, PROG, etc.) and the Comfort temperature is set to the maximum.
Step 2: If using Tybox 5701FP or 5702FP, insert two LR03 – AAA alkaline batteries into the device. If using RF6700FP, connect it to the main power supply.
Step 3: Press any button on the thermostat to activate the display screen. The current mode will be displayed as ON or = Stop.
Step 4: Press the mode button to change the current mode. ON allows for the heating system to be turned on while = Stop disables it.
Step 5: Press the + or – buttons to display the temperature setting and modify it. Press mode or wait for 5 seconds to exit.
Step 6: On the receiver, the green LED indicates that the power supply is okay while the red LED indicates that the heating demand is being executed.
Note: For further instructions on how to pair the device with a door/window magnetic contact, pairing with the Tydom app, advanced features, and troubleshooting, please refer to the detailed instruction manual by scanning the QR code or visiting the Delta Dore website.
| | mode| Tybox 5101| RF 6700FP
---|---|---|---|---
| | 2 x 1,5V LR03 – AAA Alkaline| 230 V~ +/-10%, 50 Hz 0,4W
| |
| 868,7 MHz -> 869.2 MHz (EN 300 220) – 300 m max .Maximum wireless power < 10
mW – Category 2 receiver
Output| | 100 mA max., 230V – Type 1.Y
Pilot wire (Comfort/Stop)
Input| | Load shedding (option) 115V or 230V
| -10°C / +40°C
| 80 x 84 x 21 mm| 54 x 140 x 25 mm
| IP 20| IP44
| test temperature: 75°C.
| impulse withstand voltage: 2500V
Tybox 5701 FP| Tybox 5702 FP
---|---
Tybox 5101 mode RF 6700 FP| Tybox 5101 mode 2 x RF 6700 FP
Detailed instructions
For detailed instructions: scan the QR code.
- Installation guidelines
- Pairing of a door/window magnetic contact,
- Pairing with the Tydom app
- Advanced features
- Help…
Installation
Fixed by screws or adhesive tabs
- N : Blu, Blue,
- L : Brown,
- FP : Black,
- Délest :Grey,
Radio association
The first time you power up, the green LED on the receiver flashes rapidly, indicating that it has not been paired.
-
To pair it, press the receiver button for 3 seconds, until the red LED flashes. Release the button.
-
On the Tybox, simultaneously press both the mode and + buttons for 3 seconds..
The screen will display rF00. Release the buttons. -
Press briefly on +. The screen flashes until rF is displayed, depending on the number of paired receivers
-
(e.g. : rF01 for a single receiver, rF02 for 2 receivers etc…).
-
Check that the LED on the receiver is no longer flashing.
To exit the mode, simultaneously and briefly press the mode and + buttons.
Pairing a door/window magnetic contact / Pairing the Tydom app
Consult the additional instructions accessible via the QR code at the start of
these instructions.
Settings
- Press any button to activate the display screen.
- Press mode for 10 seconds, until CF01 is displayed.
- Press + or – to adjust the setting, or press mode to move to the next menu.
CF01: Correction of the measured temperature
CF02: Button lock
CF03 : 00. Leave the setting at 00.
Use
IMPORTANT: The radiator must be in automatic mode (AUTO, PROG , …), with its Comfort temperature set to the maximum.
-
Press any button to activate the display screen. The current mode is displayed:
ON = ready for operation, = Stop.
To change it, press mode. -
From ON mode, press + or – to display the temperature setting and modify it.
-
Press mode or wait 5 seconds to exit.
When switching from mode to ON mode, the setting returns to its default value: 20°C. Indicates that the system is in Frost Protection mode (7°C, cannot be modified).
Example: open window
On the receiver:
- Green LED illuminated = power supply OK
- Red LED illuminated = heating request pending
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>