DELTA DORE RF 6600 FP Radio Pilot Wire Receiver Installation Guide

DELTA DORE RF 6600 FP Radio Pilot Wire Receiver

Product Information

• Product Name: RF 6600 FP
• Power Supply: 230V~, 50 Hz – 1,4 VA
• Radio Frequency: 868,7 MHz -> 869,2 MHz
• Maximum Radio Power: < 10 mW
• Receiver Category: 2 100 to 300 m
• Dimensions: 54 x 102 x 20 mm
• IP / IK Rating: IP 44 / IK04
• Pilot Wire Output: 0.1 A max. 230 V
• Important Information: The product can be associated with the Tydom application or a pilot wire manager for remote control of the heat emitter.

Product Usage Instructions

• To install the RF 6600 FP, follow the steps below:

1. Mount the antenna using screws or adhesive tabs.
2. Connect the power supply to N and L terminals.
3. Connect the pilot wire output to the heat emitter.
4. Press and hold the receiver button for more than 3 seconds to turn on the LEDs.
5. Follow the association procedure for either Tydom application or pilot wire manager as described in the manual.

• To operate the RF 6600 FP, follow the instructions below:
  • The LEDs indicate the current operating mode – Comfort, Eco or Frost Protection.
  • To turn off the LEDs permanently, press and hold the receiver button for 10 seconds. To turn on the LEDs, repeat the same step.
  • To override the current mode temporarily, press the receiver button. The LED flashes during an override of the Comfort mode to the Eco mode or vice versa. An override is cancelled if there is a power failure.
  • To remove all the receiver associations, hold down the receiver button for 20 seconds until the lights turn off. All the associations are removed.

PRODUCT SPECIFICATION

PRODUCT OVERVIEW

Removing the association of a receiver

1. Press the button on the receiver for 10 seconds:

   • after 3 seconds, the LEDs flash slowly.
   • after 7 seconds, the LEDs flash quickly.

2. From the control unit, send the order to delete the association (see its instructions).
   If the receiver is associated with the Tydom application, delete the association of the receiver from the application.

3. Verify that the receiver lights are no longer flashing. Receiver is removed.

Turning off the LEDs

• You can keep the LEDs turned off permanently so that they do not annoy you during the night:
  •  press and hold the receiver button for about 10 seconds.
  • all the LEDs switch off while letting the product function normally.
• To turn on the LEDs:
  • press and hold the receiver button for about 10 seconds,
  • the LEDs switch on according to the current operating mode

Installation

Association with the Tydom application

1. Switch on the installation.
   Press the button on the receiver for 3 seconds until the lights flash. Release the button.

2. Pairing with the Tydom app (Requires a Tywell Pro on the installation).
   Go to your installation’s «Settings» page, select > Add a device > Heating > Electrical > RF 6600 FP, then follow the instructions.

3. Make sure that the receiver LED has stopped flashing. The products are associated.

Association for other installations (pilot wire manager)

1. Switch on the installation.
   Press the button on the receiver for 3 seconds until the lights flash. Release the button.

2. Send the association order with the control unit (see its instructions).

3. Make sure that the receiver LED has stopped flashing. The products are associated.

Operation

• Operation
  • The LEDs show you the current mode: ou .
  • The médio (Comfort -1°C) and modérato (Comfort -2°C) modes are displayed by the LED.
  • The LEDS are off for the Frost Protection and Off modes.
  • The heat emitter must be in the automatic setting for the programmer to be able to control it.
• Override
  • You can locally interrupt the current mode up to the next change of order sent by the control unit.
  • Pressing the button carries out the override.
  • The LED flashes during an override of the Comfort mode to the Eco mode,
  • The LED flashes during an override of the Eco mode to the Comfort mode.
    Important :
    An override is cancelled if there is a power failure.

Removing all the receiver associations

1. Press the button on the receiver for 20 seconds:

   • after 3 seconds, the LEDs flash slowly.
   • after 7 seconds, the LEDs flash quickly.
     Hold down for 10 seconds until the lights turn off.

2. Release.
   All the associations are removed.

References

• Delta Dore : Solutions domotiques pour une Maison connectée

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>