DELTA DORE Tywell Pro Bioclimatic Manager Instruction Manual

DELTA DORE Tywell Pro Bioclimatic Manager

Product Information

Tywell Pro
Bioclimatic manager

Technical specifications:

• Power supply: 230 V, 50/60 Hz
• Insulation: Class II
• Max consumption (without USB connection): 1.1 W
• X3D transmission frequency: 868.7 MHz to 869.2 MHz
• Maximum wireless power: < 10 mW
• Receiver category: II
• Zigbee transmission frequency: 2.4 GHz

Tywell Control
Radio ambient box for controlling blinds and heating

Technical specifications:

• Power supply: Battery operated (3 x 1.5V – AAA LR03)
• Wireless transmission: X3D (868.7 MHz to 869.2 MHz)

Product Usage Instructions

Tywell Pro Installation
Tywell Pro must be installed on a DIN rail (35 mm) or in a consumer unit, or in a VDI unit. Only a qualified person should attempt to install the device. Tywell Pro should be protected with a 2A circuit breaker, which will also act as a power supply switch.  Avoid locations near power controllers (DHW contactor typ).

Tywell Pro Connection
Switch off the 230 V power to your installation. Connect your Tywell Pro:

• A. 230 V power supply terminal

• B. Ethernet port

• C. Configuration/Information/MAC address button

• D. System status light

• E. Remote antenna connection (optional)

• F. USB output connection (optional)

• Tywell Control Installation

  1. Switch off the 230 V power to your installation.
  2. Connect Tywell Control to your Tywell Pro using the supplied
     wires.

• Tywell Control Setup

  1. Press and hold the configuration button (F) on your Tywell Pro.
  2. Wait for the system status light to start flashing yellow.
  3. Press and hold the configuration button (F) on your Tywell Control until the system status light turns solid white.

• Associating Tywell Control with Tydom App

To associate your Tywell Control, follow these steps:

1. 1. Open the Tydom App on your smartphone or tablet.

2. Activate the Wi-Fi connection on your device and connect to your Tywell Pro.
3. If using Tydom Data, configure the application accordingly.
4. Automatic Blind Control

To enable automatic opening and closing of blinds based on sunrise and sunset:

1. Activate the blind autopilot feature via the Tydom App or Tywell Control.
2. Enable automatic opening and heat protection via the application or Tywell Control.

Included

1. Tywell Pro
2. Ethernet cable
3. Tywell Control
4. 3 batteries 1,5V – AAA LR03
5. Installation instructions /  Important product information

Technical specifications

Technical specifications Tywell Pro

• 230 V, 50/60 Hz power supply
• Class II insulation
• Max consumption (without USB connection): 1.1 W
• X3D transmission frequency: 868.7 MHz to 869.2 MHz
• Maximum wireless power < 10 mW
• Category II receiver
• Zigbee transmission frequency: 2.4 GHz to 2.4835 GHz
• Storage temperature: -20°C to +70°C
• Operating temperature: -10°C to +40°C
• IP 30
• 2-module case – Mount on DIN rail
• Install in environment with normal pollution levels

Technical specifications Tywell Control

• Power supply: 3 x 1.5 V – AAA LR03
• X3D wireless remote control device: 868.7 MHz to 869.2 MHz.
• Maximum wireless power < 10 mW
• Category 2 receiver
• Dimensions: H 92 mm x L 92 mm x D 19 mm
• IP 30
• Storage temperature: -20°C to +70°C
• Operating temperature: -10°C to +40°C

**Tywell Pro

**

Bioclimatic manager

Description

• A. 230 V power supply terminal
• B. Ethernet port
• C. Configuration/Information/MAC address button
• D. System status light
• E. Remote antenna connection (optional)
• F. USB output connection (optional)

**Tywell Control

**

Wireless controller for shutter and heating control

Description

• A. Outside temperature
• B. Weather service
• C. Indoor temperature
• D. Configuration
• E. Shutters menu
• F. Set-point temperature
• G. Low-consumption digital display
• H. Absence mode
• I. Thermal menu

Tywell Pro installation

Tywell Pro must be installed on a DIN rail (35 mm) or in a consumer unit, or in a VDI unit. Only a qualified person should attempt to install the device.
Tywell Pro should be protected with a 2A circuit breaker, which will also act as a power supply switch.
Avoid locations near power controllers (DHW contactor typ).

• Switch off the 230 V power to your installation.
• Connect your Tywell Pro:

If you do not have internet access, you will need a Wi-Fi router to install the product.
While the system does not need internet access to work, it is recommended for best results.
The 230 V power supply wires should be stripped to 8 mm. To do this, use the case to help as shown opposite.

• Restore the power to the installation.

• Download the Tydom app.

  • Depending on your unit: connect to Google Play or the App Store.
  • Find and download the free «Tydom» application.

• Turn on your smartphone or tablet Wi-Fi and connect to the same local network used by your Tywell Pro.
  If you have a router in the installation, turn off your phone’s data connection.

• Set up the Tydom application.

  • Make a note of the last 6 characters of your Tywell Pro’s MAC address (found on the front).
  • Connect to the app and follow the process.

Remote antenna
The wireless range can be adjusted to suit the installation.
Some installations will require a remote antenna compatible with X3D and Zigbee (available as an accessory).
This is advised, for example, for an installation in a metal unit or near a metal mass.

Troubleshooting Tywell ProTywell Pro’s advanced features

ly, user logged in.

Steady white| System accessible locally and remotely
Flashing orange| System accessible locally, user logged in
Steady orange| System accessible locally
Steady red| No allocated IP address
5 red flashes| Thermal safety function.

Leave a clear space around the Tywell Pro in the event that it starts to heat up.

These are the features accessible depending how long you push your Tywell Pro’s configuration button (F) for.

• Secure connection and viewing of connection status
  Briefly press the button.
  The light will flash for 10 seconds. Flashing yellow| Static IP mode
  ---|---
  Flashing blue| DHCP mode
  Flashing blue (3x)| DHCP in progress. Check that the DHCP is activated on the HUB.
  Flashing red| No network connection.
  Check the Ethernet connection.

• Change from static IP to DHCP
  Press the button for 3 seconds until the pink light flashes slowly. Release.

• Reset to factory settings
  Press the button for 30 seconds until the light stops flashing. Release.
  System status

  • DHCP mode
  • Clear product associations

Tywell Control installation

This product should be installed in a location with a temperature representative of the room needing regulation.
The recommended height is around 1.5 m and the product should be away from heat sources (fi replaces, sunlight, etc.) and draughts (windows, doors, etc.).
To avoid unwanted air movements that would distort the sensor’s temperature measurements, the wire entry into the fl ush-mounted box must be plugged (with mastic, glass wool, etc.).

IMPORTANT :
Do not install the controller on a wall in contact with the outside or in an unheated room (e.g. garage, etc.).

Tywell Control mounting

Associate Tywell Pro with the Tywell Control using the Tydom application

Screen display on first installation:

Associate a thermal receiver with the Tywell Pro using the Tydom

application

Link the thermal receiver with the Tywell Control using the Tydom

application

Follow the instructions to link the thermal receiver operated by the Tywell Control.
In the Tydom application, select:

• My devices
• Select the relevant Tywell Control
• Go to the «Advanced options» menu
• Receiver linked
• Follow the instructions to select, in the list of installed receivers, the one to be operated by the Tywell Control.The receiver selected will flash. (A receiver already associated with a Tywell Control and with a confirmed link will be greyed out and non-selectable.)

Features

Tywell Control features
The Tywell Control operates devices, optimises energy use and makes a space more comfortable.

• Centralised shutter control.
• Shutter autopilot
• Automatic shutter management notifications Heating and air conditioning management (where there is a heating receiver)
• Absence mode

Setting up shutter autopilot
Associating shutters
Associate shutters with the Tydom application.
Go to the «My devices» page of your installation, select > Add a device > Shutters > Select your device, then follow the instructions.

Automatic opening
The shutters will automatically open in the morning and close in the evening based on sunrise and sunset times.

Heat protection
Heat protection automatically manages shutters to keep your home cool. For optimum autopilot results with shutters, a Tysense Sun sensor and a Tysense Thermo outdoor temperature sensor are recommended.

In the Tydom application, select:
Tysense Sun: Add a device > Sensors > Tysense Sun, then follow the instructions.
Tysense Thermo: Add a device > Sensors > Tysense Thermo, then follow the instructions.
The sensors can be replaced by weather service data from the Tydom application as long as the Tywell Pro is connected to the internet.

Create passive zones
A passive zone is a group of shutters that react to the same indoor temperature and sun data.
In the Tydom application, select: Shutters autopilot > Set heat protection > Your zones, then follow the instructions to create the passive zone.
If the installation only has a single Tywell Control and a single sun sensor (or weather service data), create a single passive zone.
If the installation has multiple Tywell Controls and/or multiple sun sensors, you can create multiple passive zones.
All shutters on the same side and in the same room should be in the same passive zone.
Select the Tywell Control (measures indoor temperature) and the sun sensor or weather service.
Select the shutters to automatically operate for each zone.

How to activate shutter autopilot
Activate automatic opening and heat protection using the application or via the Tywell Control.
North-facing shutters do not need to be on autopilot.

References

• Delta Dore : Solutions domotiques pour une Maison connectée

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>