DELTA DORE 6702001 Wireless Controller For Shutter And Heating Control Instruction Manual

June 12, 2024
DELTA DORE

Tywell Control
Wireless controller for shutter and heating control

DELTA DORE 6702001 Wireless Controller For Shutter And Heating
Control

www.deltadore.com

Installation

DELTA DORE 6702001 Wireless Controller For Shutter And Heating Control -
room needing regulation

This product should be installed in a location with a temperature representative of the room needing regulation. The recommended height is around 1.5 m and the product should be away from heat sources (fi replaces, sunlight, etc.) and draughts (windows, doors, etc.).
To avoid unwanted air movements that would distort the sensor’s temperature measurements, the wire entry into the flush-mounted box must be plugged (with mastic, glass wool, etc.).
IMPORTANT:
Do not install the controller on a wall in contact with the outside or in an unheated room (e.g. garage, etc.).

Mounting

DELTA DORE 6702001 Wireless Controller For Shutter And Heating Control -
Mounting

Operation

The Tywell Control operates devices, optimises energy use and makes a space more comfortable.
– Centralised shutter control.
– Shutter autopilot.
For optimum autopilot results, a Tysense Sun sensor and a Tysense Thermo outdoor temperature sensor are recommended.
Alternatively, the sensors can be replaced by weather service data from the Tydom application as long as the Tywell Pro is connected to the internet.
– Automatic shutter management notifications
– Heating and air conditioning management (where there is a heating receiver)
– Absence mode
To manage your installation using the Tydom application, you need to associate all Tywell Controls with the Tywell Pro bioclimatic manager.

DELTA DORE 6702001 Wireless Controller For Shutter And Heating Control -
Tywell Control

Description

DELTA DORE 6702001 Wireless Controller For Shutter And Heating Control -
Description

Associate a thermal receiver with the Tywell Control

DELTA DORE 6702001 Wireless Controller For Shutter And Heating Control -
Associate a thermal receiver with the Tywell Control

If the Tywell Pro is already associated with the Tywell Control, associate your receiver using the Tydom application.
In the Tydom application:

Add a device
Thermals

Select the receiver and follow the process.

Follow the instructions to link the thermal receiver controlled by the Tywell Control.
In the Tydom application, select:

My devices
Select the relevant Tywell Control
Go to the Advanced options menu
Linked receiver
Follow the instructions to select, in the list of installed receivers, the one to be operated by the Tywell Control.
The selected receiver will flash.
(A receiver already associated with a Tywell Control and with a confirmed link will be greyed out and non-selectable.)

Technical specifications

– Power supply: 3 x 1.5 V – AAA LR03
– X3D wireless remote control device: 868.7 MHz to 869.2 MHz.
– Maximum wireless power < 10 mW
– Category 2 receiver
**** Dimensions: H 92 mm x L 92 mm x D 19 mm
– IP 30
– Storage temperature: -20°C to +70°C
– Operating temperature: -10°C to +40°C

Associate Tywell Pro with the Tywell Control using the Tydom application

DELTA DORE 6702001 Wireless Controller For Shutter And Heating Control -
Associate Tywell Pro with the Tywell Control using the Tydom
application

When a receiver is already associated with the Tywell Control, the display shows:

To associate Tywell Pro with the Tywell Control:
– Press the configuration button, then select:
– The Settings menu, press the button to confirm
– The Status menu, press the button to confirm
, release, then press the button again for 5 seconds.
– The Associate menu, press the button to confirm
– Select Associate a Tywell Pro, press the button to confirm
and follow the process.

Confirm the link between the thermal receiver and the Tywell Control

This step is needed if the Tywell Pro is associated with the Tywell Control (step 6)

Follow the instructions to confirm the link between the thermal receiver and the Tywell Control using the Tydom application.

In the Tydom application, select your installation, then select:

My devices
Select the relevant Tywell Control
Go to the Advanced options menu
Linked receiver
Select the receiver associated with the Tywell Control, then press Confirm.
(A receiver already associated with a Tywell Control and with a confirmed link will be greyed out and non-selectable.)

DELTA DORE 6702001 Wireless Controller For Shutter And Heating Control -
Tywell Control 2

When the link between the receiver and the Tywell Control has been established, the display shows:

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals