oceanic OCEAMIXCG88MB Floor-Mounted Mixer Instruction Manual

October 27, 2023
Oceanic

oceanic OCEAMIXCG88MB Floor-Mounted Mixer

Terms of use

  • Minimum pressure: 1 bar/ maximum: 5 bars (beyond, install a pressure reducer).
  • Make sure that the supply pressures for hot and cold water are well balanced.
  • Recommended temperature for adjusting the hot water installation: 60 ° C (maximum: 80 ° C)
  • Minimum cold water temperature: 10 ° C (a lower temperature would damage your tap). Very hard water is heavily loaded with lime stone which accelerates the scaling of your taps.
    Treating your water with a softener helps protect your facilities and extend the life of your equipment.
    The height of the purchased bathtu1b should match the installation size of this product.

Unpacking

Before handling, make sure that all components are present and visually check their good surface condition.
When mounting and / or installing, make sure that by respecting any instructions, you do not experience any difficulty in screwing, tightening, fitting.

Installation

OCEAMIXCG88MB Floor-Mounted Mixer Installation Instruction
illustration

  • Prerequisite: your water inlets (hot and cold water) must be close to ground level and oriented horizontally. The diameter of the connections is 20mm.Before you start, make sure the water supply is turned off.

[Drawing part 1]

  • Firstly, screwing the 2 flexible hoses to the mixer. Make sure that the hoses are sufficiently tightened because it will not be possible to return to tighten them later. Then insert the hoses into the long vertical tube and screw the tube to the mixer tap

[Drawing part 2]

  • Insert the flange on the tube, then screw the foot to the lower end of the tube.

[Drawing part 3]

  • Make a first connection test to both find the best positioning of the hoses in relation to the water inlets and identify the drilling points on the ground which will be used to fix the support foot.

OCEAMIXCG88MB Floor-Mounted Mixer Installation Instruction
illustration

[Drawing part 4]

  • Make sure that the drilling points will not damage the water supply pipes located under the ground. Mark the position of the pipes before any drilling. Drill, using a hammer drill, according to the drilling point marks. The drilling depth must be 4.2 cm so that the entire screw pitch remains above the ground. A mark on the bit will allow better control of the drilling depth. Insert the expansion plugs in the holes.

[Drawing part 5]

  • Place PTFE tape (such as Teflon) on the male connectors on the ground, to ensure water tightness, then screw the hoses onto these connectors (hot and cold water inlet). If the hoses are too long, you can accommodate the excess in the flange. Be careful not to pinch the hose when placing it.
    Finally, check the verticality of the assembly when tightening the foot to the ground with the supplied nuts. Finalize the installation by sliding the flange to the ground.

OCEAMIXCG88MB Floor-Mounted Mixer Installation Instruction
illustration

[Drawing part 6]

  • Connect the shower hose to the Main body and the hand shower.

[Drawing part 7]

  • Complete product drawing.

OCEAMIXCG88MB Floor-Mounted Mixer Installation Instruction
illustration

Use

The mixer allows you to use either the column head or the hose. To switch from one to the other, it depends of the position of the spur on the left side tap.

  • Spur up: the tap is closed
  • Spur facing the wall: to use the column head
  • Spur in front: to use the hose

it depends on the position of the pull rod located above the mixer tap. Depressed

  • position = use of the faucet
    Exit position = use of the shower

  • To change the flow, raise the lever more or less.

  • To change the temperature, turn the mixer knob to the left or to the right.

Maintenance / cleaning

OCEAMIXCG88MB Floor-Mounted Mixer Installation Instruction
illustration

The proper functioning of the tap therefore requires regular maintenance.

We therefore recommend:

  • never use abrasive or corrosive products. These aggressive products attack coatings and tarnish your faucet.
  • clean the chrome surface using a mild soap or soapy water and a soft cloth making sure to rinse well with clean water after cleaning.
  • regularly clean the cartridge/ tap head (at least once a year), using of a solution of water and white vinegar (let stand overnight).
  • clean the aerator-aerator by soaking it in a water / white vinegar solution.
  • activate the moving parts (inverter, lever, crosspiece, pull tab) at least once per week to ensure smooth operation over time

Flexible Connecting Pipes

Care must be taken when connecting the flexible connection pipes to the household pipework to ensure they do not bend sharply and kink or twist.

See below for recommended ways to fit the flexible connecting pipes.

Important: Failure to follow these guidelines may result in poor performance and damage to the flexible connecting pipes.

oceanic-Logo.png

www.oceanic.eu

Documents / Resources

| oceanic OCEAMIXCG88MB Floor-Mounted Mixer [pdf] Instruction Manual
OCEAMIXCG88CR, OCEAMIXCG88MB, Floor-Mounted Mixer, OCEAMIXCG88MB Floor-Mounted Mixer, Mixer
---|---

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals