SPRT SP-POS5810 Thermal Printer User Manual
- June 3, 2024
- sprt
Table of Contents
SPRT SP-POS5810 Thermal Printer
Introduction
SP-POS5810 is a new type thermal line printer. It features in fast printing
speed, low noise, good reliability, high quality. And the ribbon is needless,
this will avoid the vexation of regular maintenance.
SP-POS5810 printer is widely used in many fields because of its small size and
simple operation, especially suitable for commercial cash register, PC-POS,
bank POS and various receipts printing.
Characteristics and Specification
Printing specification
- Printing method: direct thermal
- Printing paper width: 57.5±0.5mm
- Printing density: 8 dots/mm, 384 dots/line
- Printing speed: approx. 60mm/s (valid content per line isn’t over 25%)
- Reliability:
- Printing head life span:50km
- Operating Conditions:
- Print 12 × 24 ASCII characters, 50 lines every time, intermittent and repeated
- Each dot-line printing at the same time should not exceed 25%, for each character-line’s one dot, vertical and repeated printing can not exceed 11 times
- Use specified thermal paper
- Effective printing width: 48mm
Printing Paper
- Paper Type: General Thermal Paper 57.5xΦ60 mm(MAX)
- Paper Thickness ---0.06-0.08mm
- Paper Installation: Drop-in Easy Loading
- Paper Cutting Method: Manual
Printing Font
-
ANK Character set:
12×24 dots, 1.5(W)× 3.00(H)mm; -
GB2312-80(Chinese):
24×24 dots, 3.00(W)× 3.00(H)mm.
Interface
- USB interface: Standard B type USB interface (Female).
- Cash drawer control
DC12V, 1A, 6-pin RJ-11 socket
Printing Control Command
- Character print command: supports double width and double height printing of ANK characters, user-defined characters and Chinese characters, the space between character lines is adjustable.
- Bitmap print command: supports the printing of bit map with different densities.
- GS bar code print command: supports UPC-A, UPC-E, EAN-13, EAN-8, CODE39, ITF25, CODABAR, CODE93, CODE128.
Power Supply
110VAC ~220VAC 50Hz,1A
Operation Environment
- Operation environment temperature: 0~50℃Relative humidity: 10~80%
- Storage temperature: -20~60℃
Relative humidity: 10~90%
Dimension and Weight
- Dimension: 175 (L) X 117 (W) X 99 (H) mm
- Weight: 460g (roll paper is not included)
Installation and Operation
Printer Appearance
Printer appearance like below Fig 2-1-1,Fig 2-1-2.
Paper Installation
SP-POS5810 adopts 58mm width thermal paper. The installation steps are as
below:
- When there is no paper, pls don’t press【FEED】button to avoid affecting the printing head life span. Press open button to open the case cover and put paper.
- After paper case cover is closed, pls don’t draw the paper forwards or insert paper backwards by hand.
Interface Connection
USB interface
Standard B type USB interface(Female)
Cash Drawer Interface
The cash drawer interface of SP-POS5810 is RJ-11, 6pin socket, as below,
Pin No. | Signal | Direction |
---|---|---|
1 | Chassis Ground | — |
2 | Cash drawer driver signal | Out |
3 | Cash drawer on/off status signal | In |
4 | +12V DC | Out |
5
|
N.C
|
—
6
|
Cash drawer on/off status signal ground
|
—
Power Connection
SP-POS5810 uses external power supply as 110VAC~220VAC, 50Hz, 1A,
Buttons and Indicators
Power switch
ON/OFF status of power. is off . Press “-”is on.
Feed Button
【FEED】is the feed button. Print command can allow or forbid 【FEED】on/off
status . Under allowance status, hold down【FEED】to start paper feeding,
release the button to stop.
Open Upper Cover Button
Hold the paper case cover and pull up to open it.
Power indicator light (Green)
Status of the Power indicator light: If the power is on, the indicator light
will be on.
Status Indicator light (Red) and Buzzer
The indicator light will alarm for error status.Under normal working, red
STATUS light is off. If abnormal working status happens, the light will
flicker to alarm error.
Buzzer can also alarm the abnormal working status by parameter setting. Its
error status type is same with STATUS indicator light.
When error indicator light flickers, the buzzer alarms (under the buzzer on
status), that means error occurs on the printer. Different flickering ways
represent different errors.
Error status indicating method
Light status | Buzzer status | Printer Working status |
---|---|---|
Off | Off | Normal |
Flicker 1 time and stay 1s off | Alarm 1 time and stay 1s off | Paper out and |
waiting for loading paper
Flicker 2 times and stay 1s off| Alarm 2 times and stay 1s off| Print head is
overheated and just wait a while when it gets back to
normal temperature.
Flicker 3 times and stay 1s off| Alarm 3 times and stay 1s off| Thermal print head is damaged, needs repairing.
Self-test
The self-test can check the condition of printer. In the self-test, software
version, interface type, characters, etc will be printed in order. If the
self-test receipt can be printed out correctly, it means the printer works
normally except the interface with host. Otherwise, it needs to be repaired.
Method of printing self-test: Press【FEED】button and turn on the power, then
the red indicator light will flicker at 1 time/s. Release the button within 3
times of flicker, self-test begins automatically.
Hexadecimal Dump
Press 【FEED】 button and turn on the power, the red indicator light will
flicker at 1 time/s, after 3 times then release the button, the red light will
go on flickering 3 times, then the printer will print out 3 lines message as
bellow: Hexadecimal Dump To terminate hexadecimal dump, Press FEED button
three times.
Under this mode, all the input content will be printed out as Hexadecimal
data. Press the 【FEED】 button to feed one line each time. Press 3 times,
Completed will be printed out.
The Hexadecimal Dump print mode will be exit.
Upgrade Mode
Press 【FEED】button and turn on the power, the red indicator light will flicker
at 1 time per second, after flickering 3 times then release the button. At
this moment, the printer enters into Mode Option Status. Then press 【 FEED 】
button 5 times continuously and the press time interval must be within 3s. The
indicator will flicker at 1s on and 1s off status.That means the printer has
entered into Upgrade Mode successfully.
Printing Driver Installation
Printing driver for SP-POS5810 can be downloaded from our official website (www.sprt-printer.com). The detailed path: Home page– Service-Download-Driver-Windows driver receipt printer series. After downloading, the driver name is SP-DRV2148. During the driver installation, choose printer model as “58 thermal series”. For more operation details, pls refer to the manual.
Appendix 1 Performance Index
Performance Index
Printing Characte ristics
| Printing method| ****
Thermal line
Resolution| 8dots/mm, 384dots/line
Printing speed| Max:60mm/s(25% Printing Density)
Effective Printing Width| ****
48mm
Paper Width| 57.5 mm±0.5mm
Printing support
| Self-defined Character| ****
Yes
Image
| Support Bitmap with Different Densities and Downloaded Bitmap Printing
Chinese| GB18030(Chinese):24×24
ASCII| ASCII:9×17,12×24
Bar code
| UPC-A;UPC-E;EAN-13;EAN-8;CODE39; CODE93;
CODABAR;ITF25; CODE128
Interface| USB
Function Support| Paper end Sensor, Black Mark Recognition, Overheat
Protection, Buzzer Alarm
Cash Drawer control| ****
DC12V,1A,6 lineRJ-11 Socket
Power supply| ****
AC power
| ****
110V AC~220V AC , 1A
Paper Spec
| Paper type| Thermal paper 57×Ø 60mm
---|---|---
Paper thickness| ****
0.06mm~0.08mm
Paper Supply Method| ****
Drop-in easy loading
Paper Cutting Method| ****
Manual
Physical
| Dimension| 175mm×117mm×99mm (L×W×H)
Weight| 475 g (Without roll paper)
Environ ment
| Operation Temp/Humidity| 0~50℃(Operation Temp)/10~80%(Relative Humidity)
Storage Temp/Humidity| -20~60℃(Storage Temp)/10~90% (Relative Humidity)
Life/Reli ability| ****
TPH
| ****
50km
Warning
This is a class A product. It may cause radio interference in the application
environment. In this case, the practical measures may be taken by users to
resist this interference
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>