Oceanic OCEAVT30CM2 Table Fan Diameter 30CM User Manual
- October 27, 2023
- Oceanic
Table of Contents
TABLE FAN DIAMETER 30CM
User manual
OCEAVT30CM2
Important safety instructions:
Please read this instruction manual fully before using this device and keep it safe for future reference.
- This appliance is for home use only.
- Any use other than that intended for this device, or for an application other than the one intended (e.g. commercial use), is prohibited.
- If the supply cord is damaged, it must be replaced by the manufacturer, a service agent, or a similarly qualified person in order to avoid potential hazards.
- The fan should only be used according to the rated voltage.
- When using the fan, do not handle or push objects into the grille.
- Before moving the fan, turn off the power supply first.
- This appliance can be used by children aged from 8 years and above, and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge, but only if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance should not be made by children without supervision
- Always place the device on a stable surface when using it.
- Do not let the power cord hang over the edge of a table or counter top.
- Make sure that the power cable never comes into contact with a hot surface.
- Before cleaning the fan, first disconnect from the mains, then disassemble the grille and blades. Use a soft damp cloth to wipe away grease and dust. Do not use gasoline or other corrosive liquids. Pay attention to not alter the angle of the blades.
- Water and other liquids should not be allowed to enter the motor.
- Do not cover the fan when in use.
- Unplug the fan before leaving home.
- Unplug the cord before moving.
- Do not unplug the fan by pulling on the power cable. Grasp the plug and pull it out to disconnect it.
- Do not allow hair, curtains, tablecloths and loose clothing to come into contact with the fan’s moving parts, as this may cause personal injury and property damage.
- Do not use this fan in places where flammable liquids are used or stored.
- The fan is not designed for outdoor use. The fan is for indoor use only. Do not use outdoors.
- Fan overheating protection: The fan motor is installed with a thermal fuse. When motor overheating occurs, the thermal fuse will cut off the power supply, and the motor temperature will stop rising and prevent the risk of melting or burning.
- Ensure that the fan is switched off from the electrical mains before removing the guard.
- Do not try to repair this fan yourself.
- Any repair operation must be carried out by the manufacturer, its after-sales service or a qualified repair agent so as to avoid any danger.
Appliance specifications
TECHNICAL CHARACTERISTICS
| Rated voltage | 220-240 V |
|---|---|
| Rated frequency | 50 Hz |
| Rated wattage | 40 W |
| Ambient operating temperature | 20±5 °C |
| Electrical protection class | II |
| Maximum fan flow rate | 41.04 m³/min |
| Fan sound power level | 48.82 dB(A) |
| Service value | 1,24 (m³/min)/W |
| Maximum air speed | 2.3 meters per second |
| Seasonal electric consumption | 10.62 kWh/a |
| Service value measurement standard | CEI 60879: 1986 |
EN 60704-2-7 :1998
EN 60704-1 :2010 + A11: 2012
EN 50564 :2011
Contact details for more information| Oceanic 120-126 Quai de
Bacalan. CS 11584
33000 Bordeaux
Maintenance / cleaning
- Always disconnect the power cord from the mains before carrying out any maintenance.
- Use a damp cloth (NO WET) to clean the plastic and metal surfaces.
- Never put the fan in water or any other liquid. Never use gasoline, benzene, or any other chemical to clean the fan.
- Never put the blades or other resin parts in hot water over 60.
- If the fan is not being used for a long period of time, please store it in a dry place.
Assembly:
1. Front grill
2. Blade nut
3. Blade
4. Nut for rear grille
5. Rear grille| 6. Oscillate button
7. Security screw
8. Gear selector
9. Base
---|---
Overview.
The protective grid has 4 latches and 1 screw.
J. Snap the fan motor assembly into its base starting from the front.
K. Then, interlock the base by pressing down vertically.
L. Insert the rear grille onto the rotation axis and tighten the rear nut by
hand.
M. Insert the fan propeller on its axis and tighten it manually using the
front nut.
N. Place the front protection grille and tighten the bottom screw with a
screwdriver.
O. Complete the fixing by turning the 4 latches to the closed position.
P. Make sure the screw is fully tightened.
Q. You can choose to switch to oscillating mode by pressing button 6.
R. You can choose to direct the fan vertically by moving the top of the fan.
USE
To start and select the fan speed, use the following buttons:
0–STOP
1–LOW SPEED
2–MIDDLE SPEED
3–HIGH SPEED
Operate this knob to control oscillation to allow air to cover a larger area, or to choose a directional flow at a required angle.
DISPOSAL OF WASTE
As a responsible distributor, we attach great importance to the protection of the environment. We encourage you to follow the correct disposal procedures for your device, batteries and packaging. This will help to conserve natural resources and ensure that the product and its parts are recycled in a way that is respectful of health and the environment.
You must dispose of this product and its packaging according to local laws and
regulations. Since this product contains electronic components and sometimes
batteries, the product and its accessories should be disposed of separately
from household waste when the product reaches the end of its life.
For more information on disposal and recycling procedures, contact the
authorities in your local area.
Take the device to a local collection point for recycling. Some centers accept
products for free.
Oceanic
120-126 Quai de Bacalan
CS 11584 33000 Bordeaux
Imported by:
A.M.C.
123, QUAI JULES GUESDE
94400 VITRY SUR SEINE France