NIGHTSTICK XPP-5420B Flashlight Instruction Manual
- June 6, 2024
- NIGHTSTICK
Table of Contents
NIGHTSTICK XPP-5420B Flashlight
WARNINGS
- MSHA approved for use with three AA Duracell Type PC1500, Energizer Type EN91, and Energizer Type L91 batteries only.
- Replace the batteries in fresh air only and replace all batteries at the same time. Do not mix batteries from different manufacturers or of different types.
- Energizer Lithium (Type L91) batteries are to be replaced by a qualified technician only.
- The Model Nightstick 5420 must not be opened in areas where permissibility is required.
SPECIAL INSTRUCTIONS FOR INTRINSIC SAFETY
For personal safety, always confirm the rating of any known hazardous or potentially hazardous location where the light is to be used.
BATTERY INSTALLATION
WARNING:
In order to maintain the XPP-5420’s Intrinsically Safe rating, the only AA
batteries certified for use with this light are the Duracell PC1500, Energizer
EN91 or Energizer L91 batteries.
- Do not attempt to use any other brand or model of AA batteries with this light.
- Do not attempt to use any type of rechargeable AA batteries with this light.
Warning:
To prevent ignition of a hazardous atmosphere, do not remove the lens bezel or
the reflector/battery carrier in the hazardous environment. This task must
ONLY be done in an area known to be non-hazardous.
- Loosen the locking screw located on the side of the lens cap. NOTE: Do NOT attempt to completely remove the locking screw. Doing so is not necessary and may damage the threads. The screw simply needs to be loosened enough to allow the lens bezel to unscrew.
- Unscrew the lens bezel from the housing in a counter-clockwise direction.
- Turn the light upside down and carefully shake the light in order to remove the refl ector / battery carrier. Allow the refl ector / battery carrier to slide into your hand. WARNING: Do NOT touch the refl ector surface with your fi nger. Doing so may damage the reflector surface.
- Using 3 – AA Duracell PC1500, Energizer EN91 or Energizer L91 batteries (make sure that all 3 batteries are of the same model), install the batteries in the carrier paying close attention to the markings on the battery carrier for proper battery terminal polarity alignment.
- Align the refl ector / battery carrier so that the switches on the carrier are aligned with the switches on the housing. Carefully insert the refl ector / battery carrier back into the fl ashlight housing until it is fully seated in the housing. WARNING: Be careful to not touch the refl ector surface with your fi nger. Doing so may damage the refl ector surface.
- Replace the lens bezel by screwing it onto the housing in a clockwise direction.
- Tighten locking screw. CAUTION: Do NOT over-tighten. Doing so may damage the threads and impact the light’s intrinsic safety.
OPERATION
THE XPP-5420 HAS TWO SEPARATE LIGHTING MODES
MOMENTARY FLASHLIGHT MODE
Lightly press the body switch for momentary operation. Release the switch
to turn the light off.
CONSTANT-ON FLASHLIGHT MODE
Press the body switch until it clicks and then releases for constant-on
mode. Press and release the body switch again to turn the light off.
WARRANTY
Bayco Products, Inc. warrants this product to be free from defects in
workmanship and materials for the original purchaser’s lifetime. The Limited
Lifetime Warranty includes the LEDs, housing and lenses. Rechargeable
batteries, chargers, switches, electronics and included accessories are
warranted for a period of two years with proof of purchase. Normal wear and
failures which are caused by accidents, misuse, abuse, faulty installation and
lightning damage are excluded. We will repair or replace this product should
we determine it to be defective. This is the only warranty, expressed or
implied, including any warranty of merchantability or fitness for a particular
purpose.
For a complete copy of the warranty, go to www.baycoproducts.com/bayco-
product-support/warranties. Retain your receipt for proof of purchase.
EU Declaration of Conformity
We hereby declare that the product identified above meets the requirements of
the Directives listed below. Therefore, they qualify for free movement within
markets comprising the European Union (EU), the European Economic Area (EEA).
This declaration is issued under the sole responsibility of the manufacturer.
The following EU harmonized, designated standards and technical specifications
have been applied and evaluated by: 
These Products are fully compliant and do not contain the restricted substances above levels noted in EU RoHS.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>