Marathon Lighting ML-WM-2286 LED Wall Installation Guide
- June 1, 2024
- Marathon Lighting
Table of Contents
Marathon Lighting ML-WM-2286 LED Wall
Specifications
- Product : LED Wall Light Fixture
- Model : Select Models Only
- Manufacturer: Marathon Lighting
- Power Supply: Standard Electrical Outlet
- Wattage : Adjustable (Select Models Only)
Product Usage Instructions
Standard Installation
- Tools Required: Hex Key Set
- Loosen the two (2) set screws found on the bottom of the fixture housing.
- Remove the quick mount bracket from the fixture and attach it to the junction box with the appropriate hardware (not included).
- Make the wiring connections according to the wiring diagram on Page 4. Push excess wire into the junction box.
- Lift the fixture and tilt slightly toward the quick mount bracket. Hook the fixture housing onto the quick mount bracket as shown. Take care not to pinch any wires.
- Tighten the two (2) set screws to secure the fixture housing to the quick-mount
- bracket.
- Restore power and check that the fixture is functioning properly.
Wattage Adjustment (Select Models Only)
- With the supply power off, open the bottom cover and carefully detach the LED reflector assembly.
- Adjust the controller to the desired wattage by sliding the switch on the controller.
- Reattach the LED reflector assembly and close the bottom cover.
- Restore power and check that the fixture is functioning properly.
FAQ
- Q: What tools are required for installation?
- A: You will need a Hex Key Set for installation.
- Q: How do I adjust the wattage on my LED Wall Light Fixture?
- A: For select models, you can adjust the wattage by following the Wattage Adjustment instructions provided in the manual.
- Q : Where can I find the electrical wiring diagram?
- A: The electrical wiring diagram can be found in the user manual on Page 4 or on our website at www.marathon-lighting.com.
BEFORE YOU BEGIN
Read and follow all safety instructions
WARNING
RISK OF FIRE, EXPLOSION AND ELECTRIC SHOCK
- This product should be installed, inspected, and maintained by a qualified electrician only, in accordance with the NEC (National Electric Code) and all local codes.
- Turn off electrical power before inspection, installation or removal.
- Use only UL (or other NTRL) approved wire for input/output connections.
- Minimum size 18 AWG or 14 AWG for continuous runs.
- Make sure LEDs and drivers are cool to touch when performing maintenance.
- Make sure the supply voltage is the same as the rated voltage of the luminaire.
- Do not install in a hazardous atmosphere, except where the ambient temperature does not exceed the rated operating temperature of the fixture.
- Keep tightly closed when in operation
Prepare Electrical Wiring
Electrical Requirements
- The LED driver must be supplied with the voltage specified on the product label and connected to an individual, properly grounded branch circuit protected by a 20 Ampere circuit breaker. Use min. 75°C supply.
Grounding Instructions
- The grounding and bonding of the overall system shall be done in accordance with NEC Article 600 and local codes
Before starting
- Ensure that the supply power is shut off. Unpack the fixture and ensure that there is no damage or .
- NOTE: Fixture must sealed where it contacts the mounting surface with a silicone sealant.
Tools Required
- Hex Key Set
- Wire Strippers
- Wire Cutters
Standard Installation
-
Step 1 : Loosen the two (2) set screws found on the bottom of the fixture housing
-
Step 2 : Remove the quick-mount bracket from the fixture and attach it to the junction box with the appropriate hardware (not included).
-
Step 3 : Make the wiring connections according to the wiring diagram on Page 4. Push excess wire into the junction box.
-
Step 4 : Lift the fixture and tilt slightly toward the quick mount bracket. Hook the fixture housing onto the quick mount bracket as shown. Take care not to pinch any wires.
-
Step 5 : Tighten the two (2) set screws to secure the fixture housing to the quick-mount bracket.
-
Step 6 : Restore power and check that the fixture is functioning properly
Wattage Adjustment
Wattage Adjustment (Select Models Only)
- Step 1: With the supply power off, open the bottom cover and carefully detach the LED reflector assembly. Adjust the controller to the desired wattage by sliding the switch on the controller
- Step 2 : Reattach the LED reflector assembly and close the bottom cover. Restore power and check that the fixture is functioning properly.