Marathon Lighting ML-WM-8023 Cylinder Series LED Lighting Fixture Installation Guide

May 15, 2024
Marathon Lighting

Marathon Lighting ML-WM-8023 Cylinder Series LED Lighting Fixture

Marathon Lighting ML-WM-8023 Cylinder Series LED Lighting
Fixture

LED Lighting Fixture

SAVE THESE INSTRUCTIONS

SymbolBEFORE YOU BEGIN
Read and follow all safety instructions

WARNING

RISK OF FIRE, EXPLOSION AND ELECTRIC SHOCK

  • This product should be installed, inspected, and maintained by a qualified electrician only, in accordance with the NEC (National Electric Code) and all local codes.

  • Turn off electrical power before inspection, installation or removal.

  • Use only UL (or other NTRL) approved wire for input/output connections.
    Minimum size 18 AWG or 14 AWG for continuous runs.

  • Make sure LEDs and drivers are cool to touch when performing maintenance.
    Make sure the supply voltage is the same as the rated voltage of the luminaire.

  • Do not install in a hazardous atmosphere, except where the ambient temperature does not exceed the rated operating temperature of the fixture.

  • Keep tightly closed when in operation
    Symbols

Prepare Electrical Wiring

Electrical Requirements

  • Symbol The LED driver must be supplied with the voltage specified on the product label and connected to an individual, properly grounded branch circuit protected by a 20 Ampere circuit breaker. Use min. 75°C supply.

Grounding Instructions

  • Symbol The grounding and bonding of the overall system shall be done in accordance with NEC Article 600 and local codes

LED Cylinder Light

Before starting:

  • Ensure that the supply power is shut off.
  • Unpack the fixture and ensure that there are no damaged or missing parts
  • NOTE: Fixture perimeter must be sealed where it contacts the mounting surface with a silicone sealant

Tools Required:

  • Phillips Screwdriver
  • Wire Strippers
  • Wire Cutters
  • Drill with assorted bits

Wall Mount Installation

Step 1: Remove the two (2) set screws. Put the screws in a secure place for later use. Separate the junction box bracket.
Wall Mount Installation

Step 2: Mount the junction box bracket (hardware provided by others). Wire the fixture per the diagram on Page 7. Reattach the fixture and secure with the two set screws removed in Step 1.
Wall Mount Installation

Step 3: Remove the conduits to access the Photocontrol or Directional/CCT adjustment switches.
Adjust to the desired settings and replace the conduit plugs.
Wall Mount Installation

Step 4: Restore power and check that the fixture is working properly. If the fixture is not working, turn off the power and recheck all wiring connections.
Wall Mount Installation

Before starting:

  • Ensure that the supply power is shut off.
  • Unpack the fixture and ensure that there are no damaged or missing parts
  • NOTE: Fixture perimeter must be sealed where it contacts the mounting surface with a silicone sealant

Tools Required:

  • Phillips Screwdriver
  • Wire Strippers
  • Wire Cutters
  • Drill with assorted bits

Ceiling Mount Installation

Step 1: Remove the set screws. Put the screws in a secure place for later use. Separate the junction box bracket by rotating it.
Ceiling Mount Installation

Step 2: To adjust the CCT, remove the upper canopy from the fixture by unscrewing it. Remove the conduit plug to access the CCT switch. Replace the conduit plug and canopy.
Ceiling Mount Installation

Step 3: Mount the junction box bracket to the ceiling (hardware provided by others). Wire the fixture per the diagram on Page 7. Reattach the fixture and secure with the two set screws removed in Step 1.
Ceiling Mount Installation

Step 4: Restore power and check that the fixture is working properly. If the fixture is not working, turn off the power and recheck all wiring connections.
Ceiling Mount Installation

Before starting:

  • Ensure that the supply power is shut off.
  • Unpack the fixture and ensure that there are no damaged or missing parts
  • NOTE: Fixture perimeter must be sealed where it contacts the mounting surface with a silicone sealant

Tools Required:

  • Phillips Screwdriver
  • Wire Strippers
  • Wire Cutters
  • Drill with assorted bits

Pendant Mount Installation

Step 1: Remove the set screws. Put the screws in a secure place for later use. Separate the junction box bracket from the upper canopy by rotating it.
Pendant Mount Installation

Step 2: Remove the canopy from the fixture by unscrewing it. Remove the conduit plug to access the CCT switch. Replace the conduit plug after making adjustments.
Pendant Mount Installation

Step 3: Attach the female thread cover to the top of the fixture by passing the cable through it and screwing it onto the exposed thread.
Pendant Mount Installation

Step 4: Pass the cable through the male cable cover and canopy. Attach the male cable cover to the bottom of the canopy by screwing it into the threaded hole of the canopy.
Pendant Mount Installation

Before starting:

  • Ensure that the supply power is shut off.
  • Unpack the fixture and ensure that there are no damaged or missing parts
  • NOTE: Fixture perimeter must be sealed where it contacts the mounting surface with a silicone sealant

Tools Required:

  • Phillips Screwdriver
  • Wire Strippers
  • Wire Cutters
  • Drill with assorted bits
  • Adjustable wrench

Pendant Mount Installation

Step 5: Mount the junction box bracket to the ceiling (hardware provided by others). Wire the fixture per the diagram on Page 7. Attach the canopy and secure with the set screws removed in Step 1.
LED Cylinder Light

Step 6: Restore power and check that the fixture is working properly. If the fixture is not working, turn off the power and recheck all wiring connections.

Before starting:

  • Ensure that the supply power is shut off.
  • Unpack the fixture and ensure that there are no damaged or missing parts
  • NOTE: Fixture perimeter must be sealed where it contacts the mounting surface with a silicone sealant

Tools Required:

  • Phillips Screwdriver
  • Wire Strippers
  • Wire Cutters
  • Drill with assorted bits

Direct Mount Installation

Step 1: Remove the set screws. Put the screws in a secure place for later use. Separate the mounting canopy from the fixture by rotating it.
LED Cylinder Light

Step 2: To adjust the CCT, remove the mating bracket from the fixture by unscrewing it. Remove the conduit plug to access the CCT switch. Replace the conduit plug and mating bracket.
LED Cylinder Light

Step 3: Mount the canopy to the ceiling (hardware provided by others). Wire the fixture per the diagram on Page 7. Attach the fixture to the canopy and secure with the set screws removed in Step 1.
LED Cylinder Light

Step 4: Restore power and check that the fixture is working properly. If the fixture is not working, turn off the power and recheck all wiring connections.
LED Cylinder Light

Electrical Wiring Diagram

Electrical Wiring Diagram

Logo

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Marathon Lighting User Manuals

Related Manuals