Marathon Lighting ML-GC-5584 LED Lighting Fixture Installation Guide
- June 16, 2024
- Marathon Lighting
Table of Contents
- Marathon Lighting ML-GC-5584 LED Lighting Fixture
- Product Information
- Product Usage Instructions
- LED Lighting Fixture
- Prepare Electrical Wiring
- LED Canopy Light
- Surface Mount Installation
- Pendant Mount Installation
- Electrical Wiring Diagram
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
- 2 Phillips Screw
- 2 Phillips Screw
Marathon Lighting ML-GC-5584 LED Lighting Fixture
Product Information
Specifications
- Product Name: LED Lighting Fixture
- Installation Type: Surface Mount and Pendant Mount
- Power Source: Electrical Wiring
- Color: Not specified
- Material: Not specified
Product Usage Instructions
Surface Mount Installation
Tools Required:
- Appropriate hardware for mounting the bracket (not supplied)
- Screwdriver
- Step 1: Remove the locking screw to separate the top half of the surface bracket.
- Step 2: Mount the bracket to the desired surface using the appropriate hardware (not supplied).
- Step 3: Hang the fixture on the mounted bracket.
- Step 4: Wire the supply cable from the fixture to the power source wires. Connect Black wire to Line, Green wire to Ground, and White wire to Neutral. Refer to the electrical wiring diagram on Page 6 for reference.
- Step 5: Raise the fixture to secure it with the locking screw removed in Step 1.
- Step 6: Secure the bracket with the locking screw.
Pendant Mount Installation
Tools Required:
- Two locking nuts (not supplied)
- Screwdriver
- Step 1: Remove the locking screw to separate the top half of the mounting bracket.
- Step 2: Mount the top bracket to a 3/4 trade size conduit and secure it with two locking nuts (not supplied).
- Step 3: Hang the fixture on the mounted bracket.
- Step 4: Feed the supply cable from the fixture through the conduit and wire it in the junction box. Connect Black wire to Line, Green wire to Ground, and White wire to Neutral. Refer to the electrical wiring diagram on Page 6 for reference.
- Step 5: Raise the fixture to secure it with the locking screw removed in Step 1.
- Step 6: Secure the bracket with the locking screw.
FAQ
-
Q: What are the electrical requirements for the LED Lighting Fixture?
A: The grounding and bonding of the overall system shall be done in accordance with NEC Article 600 and local codes. -
Q: What should I do before starting the installation?
A: Ensure that the supply power is shut off and inspect the fixture for any damages or defects. -
Q: What are the color and material of the LED Lighting Fixture?
A: The color and material specifications are not provided in the user manual.
LED Lighting Fixture
SAVE THESE INSTRUCTIONS
BEFORE YOU BEGIN
Read and follow all safety instructions
WARNING
RISK OF FIRE, EXPLOSION AND ELECTRIC SHOCK
- This product should be installed, inspected, and maintained by a qualified electrician only, in accordance with the NEC (National Electric Code) and all local codes.
- Turn off electrical power before inspection, installation or removal.
- Use only UL (or other NTRL) approved wire for input/output connections.
- Minimum size 18 AWG or 14 AWG for continuous runs.
- Make sure LEDs and drivers are cool to touch when performing maintenance.
- Make sure the supply voltage is the same as the rated voltage of the luminaire.
- Do not install in a hazardous atmosphere, except where the ambient temperature does not exceed the rated operating temperature of the fixture.
- Keep tightly closed when in operation
Prepare Electrical Wiring
- Electrical Requirements
- The LED driver must be supplied with the voltage specified on the product label and connected to an individual, properly grounded branch circuit protected by a 20 ampere circuit breaker. Use min. 75°C supply.
- Grounding Instructions
- The grounding and bonding of the overall system shall be done in accordance with NEC Article 600 and local codes
LED Canopy Light
Before starting:
- Ensure that the supply power is shut off.
- Unpack the fixture and ensure that there are no damaged or missing parts
Tools Required:
-
2 Phillips Screw
- Driver Wire Strippers
- Wire Cutters
Surface Mount Installation
-
Step 1: Remove the locking screw to separate the top half of the surface bracket.
-
Step 2: Mount the bracket to the desired surface using the appropriate hardware (not supplied).
-
Step 3: Hang the fixture on the mounted bracket.
-
Step 4 : Wire the supply cable from the fixture to the power source wires.
Black->Line; Green->Ground; White->Neutral SEE ELECTRICAL WIRING DIAGRAM ON PAGE 6 -
Step 5: Raise the fixture to secure with the locking screw removed in Step 1.
-
Step 6: Secure the bracket with the locking screw.
Before starting:
- Ensure that the supply power is shut off.
- Unpack the fixture and ensure that there are no damaged or
Tools Required:
-
2 Phillips Screw
- Driver Wire Strippers
- Wire Cutters
Pendant Mount Installation
-
Step 1: Remove the locking screw to separate the top half of the mounting bracket.
-
Step 2: Mount the top bracket to a 3/4″ trade size conduit as shown and secure with two locking nuts (not supplied).
-
Step 3: Hang the fixture on the mounted bracket.
-
Step 4: Feed the supply cable from the fixture through the conduit and wire in the junction box. Black->Line; Green->Ground; White->Neutral SEE ELECTRICAL WIRING DIAGRAM ON PAGE 6
-
Step 5: Raise the fixture to secure with the locking screw removed in Step 1.
-
Step 6 : Secure the bracket with the locking screw.
Electrical Wiring Diagram
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>