Marathon Lighting ML-BL-2023 LED Bollard Light Installation Guide

June 4, 2024
Marathon Lighting

Marathon Lighting ML-BL-2023 LED Bollard Light

Marathon-Lighting-ML-BL-2023-LED-Bollard-Light-PRODCUT

Specifications

  • Product Name: LED Bollard Light Fixture
  • Model Number: ML-BL-2013 / ML-BL-2023
  • Tools Required : Wire Strippers, Wire Cutters, Allen Wrench Set
  • Standard Wiring Diagram: LINE (BLACK), NEUTRAL (WHITE), GROUND (GREEN)

Product Usage Instructions

I nstallation

  1. Before starting, read and follow all safety instructions provided in the manual.
  2. Prepare electrical wiring as per the electrical requirements mentioned.
  3. Use the tools required for installation: Wire Strippers, WireCutters, Allen Wrench Set.
  4. Refer to the standard wiring diagram for proper connection of wires.
  5. Ensure proper grounding and bonding of the system according to NEC Article 600 and local codes.

Usage

  1. Connect the fixture wires (PURPLE, GRAY) to the corresponding electrical wires (LINE, NEUTRAL, GROUND).
  2. If applicable, connect any additional wires for dimming functionalities (+, -).
  3. For specific model instructions, refer to the corresponding model number section in the manual.

LED Lighting Fixture

BEFORE YOU BEGIN
Read and follow all safety instructions

WARNING: RISK OF FIRE, EXPLOSION AND ELECTRIC SHOCK

  • This product should be installed, inspected, and maintained by a qualified electrician only, following the NEC (National Electric Code) and all local codes.
  • Turn off electrical power before inspection, installation or removal.
  • Use only UL (or other NTRL) approved wire for input/output connections.
  • Minimum size 18 AWG or 14 AWG for continuous runs.
  • Make sure LEDs and drivers are cool to touch when performing maintenance.
  • Make sure the supply voltage is the same as the rated voltage of the luminaire.
  • Do not install in a hazardous atmosphere, except where the ambient temperature does not exceed the rated operating temperature of the fixture.
  • Keep tightly closed when in operation

PrepareElectrical Wiring

Electrical Requirements
The LEDdriver must be supplied with 120 to 277V, 50/60 Hz and connected to an individual, properly grounded branch circuit protected by a 20 Ampere circuit breaker. Use min. 75°C supply

Grounding Instructions
The grounding and bonding of the overall system shall be done by NECArticle 600 and local codes

LED Bollard Light

Tools Required: Wire Strippers Wire Cutters Allen Wrench Set

  • Before starting installation ensure that the power is disconnected.
  • Unpack the fixture and ensure that there are no damaged parts.
  • Use the supplied cardboard template to set the anchor bolts in concrete.
  • Be sure that the base of the concrete is elevated from the surrounding area to keep the bollard from standing in water. Allow concrete to be properly set.
  • Remove the 4 grub screws from the bollard to remove the base assembly.
  • Be sure to disconnect the orange disconnect from the cable on the terminal block.
  • Once the base is removed the base can be installed onto the anchor bolts that were previously set in.
  • Bolt down the base using the included nuts and washers.
  • Once secured attach the mains connections to the terminal block on the top of the base. Be sure to connect the cables as below Black to Black (Hot),
  • White to White (Neutral), Green to Green (Ground).
  • Once everything is connected replace the bollard body onto the base and secure with the 4 grub screws below.

Marathon-Lighting-ML-BL-2023-LED-Bollard-Light-
FIG-1Standard Wiring Diagram

Marathon-Lighting-ML-BL-2023-LED-Bollard-Light-FIG-2

FAQ

  • Q: What should I do if I encounter difficulties during installation?
    • A: If you face any challenges during installation, please contact our customer support at ph: 1-888-390-6406 for assistance.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Marathon Lighting User Manuals

Related Manuals