Marathon Lighting ML-FL-31018 LED Area Light Installation Guide

Marathon Lighting ML-FL-31018 LED Area Light

Product Information: LED Area Light

Specifications

• Installation Type: Knuckle Mount, Trunnion Mount, Slip fitter Mount
• Tools Required: Hex Key Set, Phillips screwdriver, Light
• Electrical Wiring Diagram: LED-29000 Series

Product Usage Instructions

Standard Installation (Knuckle Mount)

1. Ensure that the supply power is shut off.
2. Unpack the fixture and check for any damages.
3. Feed the power cord into the junction box or conduit. If j-box mounted, insert the threaded portion of the knuckle into the desired knock-out on the junction box.
4. Make the wiring connections according to the provided electrical wiring diagram. If dimming is not required, make sure to cap the dimming leads.
5. To aim the fixture, use a hex key to loosen the machine screw. Move the fixture head to the appropriate position and tighten the screw to lock it in position.
6. Restore power and check that the fixture is working properly.

Standard Installation (Trunnion Mount)

1. Ensure that the supply power is shut off.
2. Unpack the fixture and check for any damages.
3. Mount the fixture to the desired surface using the appropriate hardware (provided by others). Feed the power cable to a junction box or other wiring compartment.
4. Make the wiring connections according to the provided electrical wiring diagram. If dimming is not required, make sure to cap the dimming leads.
5. To aim the fixture, use a screwdriver to loosen the machine screw. Move the fixture head to the appropriate position and tighten the screw in one of the threaded slots to lock it in position.
6. Restore power and check that the fixture is working properly.

Standard Installation (Slip fitter Mount)

1. Ensure that the supply power is shut off.
2. Unpack the fixture and check for any damages.
3. Make the wiring connections according to the provided electrical wiring diagram. If dimming is not required, make sure to cap the dimming leads.
4. Slide the slip fitter onto the tenon or pole, taking care to ensure that no wires are pinched. Tighten the set screws securely to lock the slip fitter onto the tenon or pole.
5. To aim the fixture, use a hex key to loosen the machine screw on the slip fitter. Move the fixture head to the appropriate position and tighten the screw to lock it in position.
6. Restore power and check that the fixture is working properly.

Accessing the CCT/Wattage Selector

1. Remove the conduit plug as shown and set it to the desired wattage/CCT. Note: Replace the conduit plug securely to avoid water entry into the fixture.

Tunable Settings
For CCT tuning, adjust the three (3) position slide switch for the desired CCT:

FAQ

• *  **Q: What should I do if there are damages to the fixture upon unpacking?**

  • A: Contact customer support for assistance with damaged fixtures.
  • Q: Are there any specific electrical requirements for installation?
  • A: The grounding and bonding of the overall system shall be done in accordance with NEC Article 600 and local codes.
  • Q: Is dimming required for installation?
  • A: Dimming is optional. If not required, make sure to cap the dimming leads during wiring.
  • Q: How do I aim the fixture after installation?
  • A: Use a hex key or screwdriver to loosen the machine screw, move the fixture head to the desired position, and tighten the screw to lock it in place.
  • Q: How can I access the CCT/Wattage Selector?

A: Remove the conduit plug as shown in the instructions and set it to the desired wattage/CCT.

LED Area Light

SAVE THESE INSTRUCTIONS

BEFORE YOU BEGIN
Read and follow all safety instructions

WARNING

RISK OF FIRE, EXPLOSION AND ELECTRIC SHOCK

• This product should be installed, inspected, and maintained by a qualified electrician only, in accordance with the NEC (National Electric Code) and all local codes.
• Turn off electrical power before inspection, installation or removal.
• Use only UL (or other NTRL) approved wire for input/output connections.
• Minimum size 18 AWG or 14 AWG for continuous runs.
• Make sure LEDs and drivers are cool to touch when performing maintenance.
• Make sure the supply voltage is the same as the rated voltage of the luminaire.
• Do not install in a hazardous atmosphere, except where the ambient temperature does not exceed the rated operating temperature of the fixture.
• Keep tightly closed when in operation
• Prepare Electrical Wiring

Electrical Requirements
The LED driver must be supplied with the voltage specified on the product label and connected to an individual, properly grounded branch circuit protected by a 20 Ampere circuit breaker. Use min. 75°C supply.

Grounding Instructions
The grounding and bonding of the overall system shall be done in accordance with NEC Article 600 and local codes

Before starting

• Ensure that the supply power is shut off.
• Unpack the fixture and ensure that there are no damaged or .

Tools Required: Hex Key Set

• Hex Key Set
• Wire Strippers
• Wire Cutters
• Phillips screwdriver

Standard Installation (Knuckle Mount)

1. Step 1 : Feed the power cord into the junction box or conduit. If j-box mounted, insert the threaded portion of the knuckle into the desired knock-out on the junction box.
2. Step 2 : Make the wiring connections according to the diagram on Page 6. If dimming is not required, make sure the dimming leads are capped.
3. Step 3 : To aim the fixture, use a hex key to loosen the machine screw. Move the fixture head to the appropriate position and tighten the screw to lock it in position.
4. Step 4 : Restore power and check that the fixture is working properly.

Before starting:

• Ensure that the supply power is shut off.
• Unpack the fixture and ensure that there are no damaged or .

Tools Required:

• Wire Strippers
• Wire Cutters
• Phillips screwdriver

Standard Installation (Trunnion Mount)

1. Step 1 : Mount the fixture to the desired surface using the appropriate hardware (provided by others). Feed the power cable to a junction box or other wiring compartment.

2. Step 2 : Make the wiring connections according to the diagram on Page 6. If dimming is not required,make sure the dimming leads are capped.
   

3. Step 3 : To aim the fixture, use a screwdriver to loosen the machine screw. Move the fixture head to the appropriate position and tighten the screw in one of the threaded slots to lock it in position .

4. Step 4 : Restore power and check that the fixture is working properly. 

Before starting:

• Ensure that the supply power is shut off.
• Unpack the fixture and ensure that there are no damaged or .

Tools Required:

• Hex Key Set Wire
• Strippers Wire
• Cutters
• Phillips Screwdriver

Standard Installation (Slipfitter Mount)

1. Step 1 : Make the wiring connections according to the diagram on Page 6. If dimming is not required, make sure the dimming leads are capped.
2. Step 2 : Slide the slipfitter onto the tenon or pole taking care to ensure that no wires are pinched. Tighten the set screws securely to lock the slipfitter onto the tenon or pole.
3. Step 3 : To aim the fixture, use a hex key to loosen the machine screw on the slipfitter. Move the fixture head to the appropriate position and tighten the screw to lock it in position.
4. Step 4 : Restore power and check that the fixture is working properly.
   

Accessing the CCT/Wattage Selector

1. Step 1 : Remove the conduit plug as shown and set to the desired wattage/CCT.
   NOTE : Replace the conduit plug securely to avoid water entry into the fixture.

Tunable Settings

For CCT tuning, adjust the three (3) position slide switch for desired CCT:

Switch Position

For Wattage tuning, adjust the three (3) position slide switch for desired wattage:

Switch Position

Electrical Wiring Diagram

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>