XIAMEN ACEVCN13P1IW Electric Vehicle AC Charger User Manual

June 1, 2024
Xiamen

XIAMEN-LOGO

XIAMEN ACEVCN13P1IW Electric Vehicle AC Charger

Product Usage Instructions

READY
Standby – Blue Light The READY light stays steady in standby mode.

CHARGE
Waiting for Charging – Green Light After the vehicle connector is connected to the vehicle inlet, the CHARGE light is constantly lit.

CHARGE
Charging – Green Light Flashing The CHARGE light flashes while charging.

FAULT
Fault – Red Light
The red light is lit while at fault. Please refer to section 9.3 Error and Warning Messages for detailed information.

  • Step 1: Use a screwdriver to loosen the fixed screws on the rear of the charger, then remove the front cover (for 4G Version).
  • Step 2: Insert the SIM card according to the picture’s instructions (for 4G Version).
  • Step 3: Tighten the screws on the front cover after putting it back. The recommended screw torque is 1.0 N.m (9.6 lbf.in) (for 4G Version).

Tools and Materials Required

  • This device should be mounted at a height between 600mm (24 inches) and 1.2m (4 feet) from the ground.

FAQ

  • Q: What should I do if the fault light is on?
  • A: If the fault light is on, please refer to section 9.3 Error and Warning Messages in the user manual for detailed information on troubleshooting steps.

Specification

Model Name GMEV40CIC1B-WC
Rated Input Voltage 200-240 VAC / Single Phase
Rated Output Current 16/32/40/48A
AC Power Frequency 60 Hz
Input Protection UVP, OVP, RCD, SPD, Ground Fault Protection
Output Protection OCP, OTP, Control Pilot Fault Protection
Output Interface SAE J1772 AC Charging Connector
Storage Temperature -40°F to 158°F
Operation Temperature -22°F to 122°F
Relative Operation Humidity 95% RH Maximum
Relative Storage Humidity 95% RH Maximum
Version LAN Version / Wi-Fi Version
RJ45 Cable Inlet*1 10M/100M Base-T
Wi-Fi Function*2 802.11 b/g/n
3G/4G Fnction*3 /
Cable Length 18ft
Protection Level Type 3
Installation Type Wall-Mounted
Altitude ≤ 6561ft
Status Indication Red, Green, Blue LED
  1. LAN Version or Wi-Fi Version
  2. Wi-Fi Version

Status Description of the Charger Indication Light

XIAMEN-ACEVCN13P1IW-Electric-Vehicle-AC-Charger-FIG-1 XIAMEN-ACEVCN13P1IW-Electric-Vehicle-AC-Charger-
FIG-2

Packing List

XIAMEN-ACEVCN13P1IW-Electric-Vehicle-AC-Charger-FIG-3

No. Product Name Quantity Note
1 AC Charger (With Charging Cable) 1
2 User Manual 1
3 Wall-Mounted Bracket 1
4 M5 teeth screws 2
5 M6 Hexagonal Expansion Screws 4
6 RFID Card (RFID Version Only) 2

Installation Instructions

Safety Requirements

  • Be sure to preview the user manual and ensure local building and electrical codes are reviewed before installing the AC charger.
  • The AC charger should be installed by a qualified technician according to the user manual and local safety regulations.
  • Use appropriate protection when connecting to the main power distribution cable.
  • Type B, C or D breakers with the rating current for a table should be installed in the upstream AC distribution box.
  • Disconnect switch for each ungrounded conductor of AC input shall be provided by others per the National Electric Code, ANSI/NFPA 70.

Installation Steps

  • Step 1: Use the screwdriver to loosen the 13 fixed screws on the rear of the charger, then remove the front cover (for 4G Version).XIAMEN-ACEVCN13P1IW-Electric-Vehicle-AC-Charger-FIG-4
  • Step 2: Insert the SIM card according to the picture’s instructions (for 4G Version).XIAMEN-ACEVCN13P1IW-Electric-Vehicle-AC-Charger-FIG-5
  • Step 3: Tighten 13 screws on the front cover after the front cover is put back, the recommended screw torque is 1.0 N.m (9.6 lbf. in) (for 4G Version).

XIAMEN-ACEVCN13P1IW-Electric-Vehicle-AC-Charger-FIG-6

Wiring

GROUNDING INSTRUCTIONS
This product must be grounded. If it should malfunction or break down, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This product is equipped with a cord having an equipment grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded under all local codes and ordinances.
WARNING – Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the product is properly grounded. Do not modify the plug provided with the product – if it will not fit the outlet, have a proper outlet installed by a qualified electrician.

For safe use of electricity, please add circuit breaker protection in the input part of the charging pile. Connect the L1 lead to the grid L1, connect the L2 lead to the grid L2, and connect the PE lead to the grid PE (for all Versions).

XIAMEN-ACEVCN13P1IW-Electric-Vehicle-AC-Charger-FIG-7

Circuit Breaker Options table

Output Amperage (A)| 16A| 32A| 40A| 48A
Circuit Breaker Options (A)| 20A| 40A| 50A| 60A

Tools and Materials Required

Tools required before installing the Wall-Mounted charger, gather the following tools:

  • Wire stripper
  • Crimpers for European terminals
  • Phillips screwdriver for M5
  • Slotted screwdriver for 4~5.5MM
  • Adjustable Wrench M6
  • Head gasket screw 10-10.5mm
  • Voltmeter or digital multi-meter (for measuring AC voltage at the installation site)
  • The inserting cable should meet the best waterproof performance. It is recommended to use 3 3-core / 7AWG cable (XLPE or equivalent cable) to pull the cable from the distribution box.
  • Level ruler
  • Pencil or marker
  • Machine drill

Installation Instructions
“This device shall be mounted at a sufficient height from grade such that the height of the storage means for the coupling device is located between 600mm (24 inches) and 1.2m (4 feet) from grade.”

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals