ricoo S5044 TV Wall Mount with Pan and Tilt Function Instruction Manual
- June 12, 2024
- ricoo
Table of Contents
ricoo S5044 TV Wall Mount with Pan and Tilt Function
Product Information
- Product Name: Screen Mount
- Model Number : S5044
- Manufacturer: E.N.Z. Engineering GmbH – Maximum Load
- Weight: 40kg / 88lbs – VESA Hole
- Distance: Supports various distances ranging from 75mm to 400mm
- Suitable for : Solid concrete walls
Product Usage Instructions:
- Before installation, check the distance between the VESA mounting holes on your display.
- Make sure not to exceed the listed load weight to avoid property damage or serious injury.
- Ensure that the supplied plastic anchors are only used for solid concrete walls.
- Use a professional bubble level for accurate installation.
- Follow the provided assembly instructions and use the specified screws, spacers, and washers as mentioned below:
- A x1, B x2, C x2, D x1, E x8, F x1, M-A x4, M-B x4, M-C x4, M-D x4, M-E x4, M-F x4, M-G x4, M-H x8, M-I x8, W-A x6, W-B x6, W-C x5
- Use the appropriate screws based on the length required (e.g., M5x14, M8x30). – If the screws M-C, M-D, or M-E are too long, use the plastic spacers M-H or M-I (as shown in Step 5A).
- Follow the step-by-step instructions provided in the manual to assemble and mount the screen securely.
- Make sure to attach the screen mount to the appropriate VESA hole distance on the back of your display.
- Once the installation is complete, ensure that everything is securely tightened.
- The top side of the screen mount is labeled as “Oberseite” (DE), “Top” (EN), “Toupie” (FR), “Cima” (ES), “Vetta” (IT).
- If necessary, adjust the position of the screen mount using the provided screws and spacers.
- Once the installation is finished, verify that everything is properly assembled and secured. Note: For any further assistance or support, contact E.N.Z. Engineering GmbH via email at support@ricoo.de or visit their website at www.ricoo.eu.
Warning: Do not exceed listed load weight. Property damage oder serious injury may occur!
Scope of delivery
We recommend using a professional level.
NOTE: READ THE ENTIRE INSTRUCTION MANUAL BEFORE YOU START INSTALLATION AND ASSEMBLY
- Please note: Images in these assembly instructions are only technical presentation of the product. Actual product design may vary minimally.
- Do not begin the installation until you have read and understood all the instructions and warnings contained in this installation sheet. If you have any questions regarding any of the instructions or warnings, please contact your local distributor. This product was designed to be installed and used ONLY as specified in this manual. Improper installation of this product may cause damage or serious injury. This product may only be assembled / installed by the technical staff. Make sure that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components. Always use an assistant or mechanical lifting equipment to safely lift and position the equipment.
- Make sure that before and after the installation of the product neither you nor somebody else can be injured and other objects can be damaged. In case of doubt request for help from an expert. This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury. Tighten screws firmly, but do not over tighten. Over tightening can cause damage the items, this greatly reduces their holding power.
- By reason of large television construction types on the market, we can’t adjust our screen installation materials for each screen type. Therefore it is possible that the screws
- which are numerously delivered don’t fit with your TV/Monitor. We ask for your understanding that we can’t cover up all possibilities of many screen types.
- Each wall is built up of different materials which can result a special requirement. Therefore we are concentrated on the delivery of installation materials only for mass concrete
- walls. Use our included installation accessories only for mass concrete walls.
- When mounting on the wooden beams wall, make sure that the fastening screws are anchored in the center of the beams. It is highly recommended to use a beamfinder. If your
- walls have a special demand of materials, we advise you to ask in an expert shop for a suitable acquirement of the installation materials.
ASSEMBLY INSTRUCTION
Use the matching screws and spacers for your display
Use the matching screws and spacers for your display
E.N.Z. Engineering GmbH, Salzmatten 6, 79341 Kenzingen (Germany)
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>