QTech Q3 HVLP Turbine User Manual
- June 2, 2024
- QTech
Table of Contents
- QTech Q3 HVLP Turbine
- Product Information
- FAQ
- ELECTRIC SHOCK HAZARD
- GETTING STARTED
- CHANGING THE SHAPE OF THE FAN
- SPRAYING TECHNIQUES
- AIR CAP SET SELECTION
- VISCOSITY GUIDE
- GENERAL CLEANING
- ACHIEVING THE DESIRED FINISH
- PARTS DESCRIPTION
- TURBINE CARE & MAINTENANCE
- CUP ASSEMBLIES | HOSE
- CONTACT
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
QTech Q3 HVLP Turbine
Product Information
Specifications
- Brand: QTech Global Ltd
- Model: QTech3 HVLP Turbine
- Gun Types: Q70 Suction Gun, Q75G Gravity Gun
- Address: 1a Quillyburn Business Park, Banbridge Road, Dromore, County Down BT25 1BY
- Email: sales@qtechspray.com
- Phone: UK 01895 276751, ROI 0 1690 3162, International +44 1895 276751
- Website: www.QTechSpray.com
FAQ
Q: Can I use flammable materials with the QTech HVLP Turbine?
A: No, it is advised not to use flammable or combustible materials near the turbine to avoid fire and explosion hazards.
Q: How should I store the unit when not in use?
A: Store the unit indoors in a dry location, preferably on the floor in a basement setting.
Q: What should I do if the appliance malfunctions?
A: If the appliance malfunctions, disconnect the power cord and seek assistance from a qualified electrician or service person.
CAUTION
- This manual contains important warnings and information
- PLEASE READ & KEEP FOR FUTURE REFERENCE
- VERSION HVLP3-11-0223
QTech Global Ltd
- 1a Quillyburn Business Park, Banbridge Road, Dromore, County Down BT25 1BY
- Declares that
QTech5 HVLP Turbines
- are in conformity with
EN 60335-1
- according to
- 73/23/EEC Low Voltage Directive
Please read these instructions carefully before using the equipment
EARTHING
This appliance must be earthed. If it should malfunction or break down,
earthing provides a path of least resistance for electric current to reduce
the risk of electric shock. This appliance is equipped with a cord having an
equipment-earthing conductor and an earthed plug. The plug must be inserted
into an appropriate outlet that is properly installed and earthed under all
local codes and legislation.
ELECTRIC SHOCK HAZARD
Improper connection of the equipment grounding conductor can result in the risk of electric shock.
- Check with a qualified electrician or service person if you are in doubt as to whether the outlet is properly grounded.
- Use only a 3-wire extension cord that has a 3-blade earthing plug and a 3-slot receptacle that accepts the plug on the product.
- An undersized cord results in a drop in line voltage and loss of power and overheating.
- Do not modify the plug provided with the appliance. If it will not fit the outlet, have a proper outlet installed by a qualified electrician.
- To reduce the risk of electric shock or injury, do not be exposed to rain.
- Never allow unit to freeze.
- Always store the unit inside in a dry location. Store on the floor if in a basement setting.
- The operator must wear shoes and the floor must not be wet.
FIRE & EXPLOSION HAZARD
This QTech HVLP Turbine must not be used in an area contaminated by volatile
or flammable materials since sparking can be expected in the normal operation
of the motor. This could ignite the contaminants causing a dangerous
explosion.
- Do not spray flammable or combustible materials near an open flame or sources of ignition such as cigarettes, motors, and electrical equipment.
- Keep the spray area well-ventilated. Keep a good supply of fresh air moving through the area. Keep the turbine in a well-ventilated area.
- Do not spray the turbine.
- Turn off and disconnect the power cord before servicing the equipment.
- Do not smoke in the spray area.
- Do not operate light switches, engines, or similar spark-producing products in the spray area.
- Keep the area clean and free of paint or solvent containers, rags, and other flammable materials.
- Fire extinguisher equipment shall be present and working.
- Sprayer generates sparks. When flammable liquid is used in or near the sprayer or for flushing or cleaning, keep sprayer at least 6 m away from explosive vapours or the spraying area.
- Ensure ground prongs are intact on sprayer and extension cords.
- Always disconnect the unit from the main supply when filling the paint container.
- Never use 1,1,1-trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or fluids containing such solvents in equipment with aluminium-wetted parts. Such use could result in a serious chemical reaction, with the possibility of explosion.
- Consult your fluid suppliers to ensure that the fluids being used are compatible with aluminium parts.
GETTING STARTED
NOTE
Throughout this manual we have used the generic word ‘Paint’ to describe all
and any coatings. Please substitute the word ‘Paint’ for whatever finish or
coating you are spraying.
Your QTech HVLP Gun has been adjusted at the factory and is ready for
spraying. To clean out any impurities that may have accumulated during
assembly or shipping, we recommend spraying a small quantity of clean paint
thinner through the gun. Before tackling any serious spraying, experiment with
the gun on a scrap piece of wood until you become familiar with all the
controls.
HOSE CONNECTION
Connect the hex nut at the end of the hose (female connector) to the turbine
air outlet. Tighten this nut lightly. Overturning could cause the internal
manifold to rotate and break the internal seal to the motor. A Male Quick
Connect Coupling 10-2010 is available as an accessory for the connection to
the turbine.
AIR CONTROL VALVE
The Air Control Valve 10-2003 is located on the hose next to the brass quick-
connect. It provides you with a means of controlling the airflow through the
gun. It offers fingertip control when needed to reduce bounce back and
overspray. It is important to remember that the air control valve – is the
‘last in the chain’ of operations after:
- Thinning the paint
- Adjusting the shape and size of the spray pattern
- Adjusting the flow of paint through the gun
After performing these operations, you should spray a few passes onto a scrap
piece of plywood or cardboard. This will allow you to determine if the paint
levels nicely. Once the Gun is producing a perfect finish with full air, you
may then experiment with turning the air down until bounce back is reduced to
a minimum. However, if orange-peel results, you have no option but to turn the
air up again
a slight amount.
PLASTIC DIAPHRAGM
The 1-litre pressurised suction cup has a Plastic Diaphragm 10-2005 (not found
in the gravity spray gun). This diaphragm prevents paint from entering the
Pressure Tube 10-2000. The small air hole in the diaphragm should not be
placed directly below the air hole in the nipple. Position the diaphragm hole
to the rear of the cup. The spray gun can be turned to different angles when
spraying but never beyond horizontal.
CHANGING THE SHAPE OF THE FAN
-
Loosen the Collar 10-2080. Turn the Air Cap to the horizontal position then re-tighten the collar to lock it into place. This setting produces a vertical spray pattern.
This pattern is used more than any other by experienced spray painters. -
Setting the air cap in a vertical position produces a horizontal spray pattern.
To lock it in position, tighten the collar. The horizontal fan pattern is the most useful for painting vertically such as a doorframe.
CHANGING THE SIZE OF THE FAN
- To produce a smaller fan pattern, turn the Pattern Control Knob counterclockwise. Because the spray pattern size is now much smaller, you must turn down the amount of paint spraying through the nozzle at the Fluid Adjusting Knob 10-2093 (rear of gun). If you do not do this, you will get runs.
- To set the fluid output, simply turn the fluid adjusting knob counter-clockwise for more ‘paint’ and clockwise for less. Once you set the fluid to your liking, you can leave it in this position – unless of course, you change the size of the fan pattern.
- For the very smallest pattern (less than 1”), you must move the gun closer to the workpiece – but don’t forget to reduce the amount of paint at the fluid
adjusting knob.
USING A GRAVITY CUP
When using a gravity cup ensure that the de-pressurizing procedure as
explained on page 18 is adhered to.
SPRAYING TECHNIQUES
The spray gun should be held perpendicular to the surface at all times. HOLD
THE GUN NO MORE THAN 8” (20cm) AWAY FROM THE SURFACE TO BE PAINTED.
CORRECT METHOD
Start off the piece. Pull the trigger and move the spray gun in the direction
you want to spray. Continue off the edge of the piece on the other end before
releasing the trigger. Between each successive pass, overlap by about a half.
INCORRECT METHOD
CAUTION | Never, for any reason, point the spray gun directly at the face, or head of a person.
AIR CAP SET SELECTION
- Six additional size setups are available as accessories.
- Size # 4 (1.5mm) is standard with all QTech HVLP guns.
- 1.0mm, 1.3mm or 1.5mm can be used for any type of fine-finishing application. The larger sizes such as 1.8mm allow for more fluid output – desirable with fast-drying lacquers.
AIR CAP SET 5100 SERIES
-
Product code 10-2023 0.8mm (.031″)
SUPER-FINE OUTPUT SHADING, STAINS. -
Product code 10-2024 1.0mm (.039″)
FINE OUTPUT SHADING, STAINS, WATERBORNE COATINGS. -
Product code 10-2025 1.3mm (.051″)
FINE – MEDIUM OUTPUT -STANDARD WATER-BASED LACQUERS, ACRYLICS, POLYURETHANE, STAINS. -
Product code 10-2026 1.5mm (.059″)
MEDIUM OUTPUT Similar to No. 3 but with more coverage.
Best for AUTOMOTIVE ENAMELS, LACQUER and LATEX for cabinetry and furniture. Also VARNISHES, PRIMERS, OIL-BASED PAINTS. -
Product code 10-2027 1.8mm (.070″)
HIGH OUTPUT Larger surfaces, thick layers, spotted effects.
SEALERS, VARNISH, POLYURETHANE, OIL-BASED PAINTS, ENAMELS, EPOXIES, LATEX on walls, ceilings etc. -
Product code 10-2028 2.0mm (.078″)
EXTRA HIGH OUTPUT Very heavy flows, fast coverage.
STONE FINISH PAINTS, TEXTURE COATING, INDUSTRIAL PRIMERS, MULTI-FLECK PAINTS, LATEX on walls, ceilings etc. -
Product code 10-2029 2.5mm (.098″)
MAXIMUM HIGH OUTPUT Heavy flows faster coverage.
LATEX HOUSE PAINT on walls etc.
VISCOSITY GUIDE
-
A Viscosity Cup (Ford #4 Standard) is included with your QTech system. To test the viscosity of the paint material, fill the viscosity cup to the brim and time how long it takes for the liquid to empty out through the hole. We recommend you experiment to find the ideal viscosity for your application and record the information for the next time.
-
Always check with the manufacturer of the coating for assistance in thinning
for spraying. If their product is only designed to be brushed, they may not be too helpful. But remember that any type of coating can be sprayed if it is thinned correctly (with the appropriate solvent) and you have installed the ideal aircap set. -
The chart below illustrates how many SECONDS it should take for the
material to flow out of the viscosity cup. This is only an approximate guide. -
We suggest thinning around 25% to begin with but this may contravene the air quality control laws for your location. The solvent used for thinning is usually the solvent mentioned on the can (instructions for ‘cleaning the brushes’). However, please check with the coatings manufacturer. The aim is to thin as little as possible.
Auto | 18 – 20 | Primers | 30 – 40 |
---|---|---|---|
Lacquers | 18 – 20 | Sanding Sealers | 20 – 22 |
Enamels | 20 – 25 | Stains | Undiluted |
Latex | 20 – 30 | Creosote | Undiluted |
Oil-based | 20 – 25 | Polyurethanes | 20 – 25 |
HVLP spraying is more friendly to the environment than most methods of spraying. It reduces appreciably the amount of unnecessary misting and fogging (overspray) associated with high-pressure spraying. Spraying with Nitrocellulose lacquer can be hazardous. The lacquer, fumes and overspray are toxic, flammable and explosive. If spraying must be done inside an enclosed area, ventilate well. Spray close to an open window or door and situate a fan to draw out the fumes (an explosion-proof motor and explosion-proof lighting will be necessary). Please check with the Local Authority having jurisdiction on this matter.
A WORD ABOUT LATEX
-
Although Latex Paint was never originally intended to be sprayed, a professional finish can be achieved by following a few simple rules. (Please do not confuse latex with the newer water-based coatings). For work such as cabinetry or trim, our equipment can be used successfully with latex paint. The latex will have to be thinned with WATER – approximately 10-30% depending on the brand of
paint. And to improve the finish even more, you can use an additive that will slow down the drying process so that the paint levels out nicely. One product available is Floetrol from the Flood Company in Ohio. Call 0845-0618899 for further information. -
The recommended air cap size setup is either 1.5mm or 1.8mm for household trim, louvre doors etc. The latex paint should be ‘finish-quality’ and not a
cheaper grade. -
When spraying latex, please adjust the Fluid Knob 10-2093 to limit the paint to a finer spray. This will increase the ratio of air to paint and result in better atomization and a beautiful finish. (Factually speaking, it doesn’t increase the ratio of air to paint but does the opposite – it allows the air atomizing power to work on less paint thereby improving the quality of atomization). Also, it is usually helpful to remove the air control valve so that more air passes through the spray gun. Finally, adjust the pattern to a maximum size of 8” – 9” (20cm) – smaller is ok. Apply a wet coating (wet like a lake).
-
Although it is possible to use our equipment for house painting (walls), and many end users do, we feel that an airless gun or power roller is better suited for that kind of job. However, if you decide to do this kind of work, you will need the 2.0mm or 2.5mm air cap set.
-
Remember, when you buy a can of paint, lacquer, polyurethane, varnish etc. over the counter, it will most likely be formulated for brushing. That means, it will be too viscous (thick) and will require thinning to spray successfully. This is true even when spraying is mentioned on the label of the can. Check with the manufacturer of the coating to obtain advice on thinning their product. Unfortunately, sometimes you may encounter Technical Sales Personnel who have very little experience or knowledge about
-
HVLP Turbine spraying.
GENERAL CLEANING
To clean the gun after each use, empty all paint from the cup. Use a solvent-
soaked rag to clean the residue in the cup. Then, spray some clean solvent
through the gun into a clean rag (to avoid filling the room with unnecessary
spray) or a bucket. Repeat until the inside of the fluid passages in the gun,
metal fluid tube etc are clean. Use the wet rag to wipe off the air cap and tip
of the fluid nozzle.
The air cap can be soaked in thinner.
If this type of cleaning is done while the paint is still wet in the gun, it
should be all that is necessary to keep the gun clean enough for next time. Do
not leave liquids in the cup overnight or for long periods.
Do not restrict the fluid nozzle when cleaning (by putting your finger over the
nozzle orifice) – this will drive thinned paint up the pressure tube and into
the spray gun which is undesirable.
PLEASE DO NOT USE A WIRE BRUSH OR ANYTHING METAL TO CLEAN THE GUN OR CUP AS
THIS WILL CAUSE DAMAGE.
DO NOT disassemble the cup assembly – threads in your cup have been sealed at
the factory to prevent leakage under pressure.
The standard 1 quart (1000cc) cup can be used with most coatings (including
water-based). Also available as an accessory is our Teflon Coated Cup 10-2008.
CAUTION | Never soak the complete spray gun in solvent as this removes
the grease from the parts and distributes thinned paints throughout the air
passages. It could also damage internal parts such as the spindle valve or
valve seals.
It may sometimes be necessary to soak the air cap, nozzle, needle, air
diffuser and air divider. You may soak only the metal parts in solvent and
clean with a soft bristle cleaning brush. To reassemble, first oil or grease
all moving and threaded parts.
CAUTION | Do not lay the gun down on its side with liquid material in it.
When not in use the cup lid should not be clamped down hard as this will cause
the gasket to flatten out.
CLEANING FLUID PASSAGES
To clean, flush solvent through the spray gun while the paint is still wet
inside
the gun. If this type of quick cleaning is performed frequently, the spray gun
will function well for many years. 99% of problems with a spray gun stem from
clogs in the fluid passages and (perhaps more important), the pressure tube air
passages. See page 16 – NO PAINT (OR VERY LITTLE PAINT).
CLEANING BEHIND THE FLUID NOZZLE
Remove the Collar 10-2080 and Aircap. Using the supplied wrench, remove the
Fluid Nozzle. Once the fluid nozzle is removed please be careful that the Air
Diffuser 10-2081 does not fall out of the gun. Use the cleaning brush and
appropriate solvent to clean behind the fluid nozzle. The air cap, fluid nozzle,
needle, air diffuser and air divider may be soaked in solvent. To remove the
needle, remove the Fluid Knob 10-2093, Spring 10-2092 from the rear of the
gun.
The needle can then be soaked and later wiped clean.
When reinstalling the air diffuser, note that there is a locating pin on the
backside. This pin must be located into the matching hole in the Air Divider
10-2084.
PLEASE DO NOT SOAK THE WHOLE GUN IN ANY LIQUID.
THIS IS NEVER NECESSARY OR ADVISABLE.
CLOGGED GUN – THE FLUID COUPLER
If the Fluid Coupler is clogged with dried paint it must be cleaned while in
place in the gun. The fluid coupler should not be removed. Remove the cup
assembly by loosening the nut. Use the supplied cleaning brush to unclog the
inside of the fluid coupler using a solvent. Replace the cup. Before
tightening, position the cup to the preferred position and tighten the nut.
ACHIEVING THE DESIRED FINISH
ORANGE PEEL
If the finish is rough and resembles orange peel then the material is too
thick.
(Or perhaps you have the air control valve turned down – please check that it
is fully open). The ‘paint’ will not atomize properly and the surface will be
spotty.
To remedy this, add more thinner (or the appropriate solvent). For fast-drying
products such as lacquers, you may also want to add a lacquer retarder. This
will slow the drying time allowing the material to flow out and level nicely.
Retarders are available for other coatings too, such as Penetrol for oil-based
paints or Floetrol for latex house paints. These products go under different
names such as flow-out additives etc. Please check with the coatings
manufacturer.
NOTE
With the newer water-based materials ‘orange peel’ is usually a result of
spraying on too thick a film. Try spraying an extremely THIN FILM, but still
WET coat. With most other coatings, orange peel is caused by the material
being too thick or not having enough atomizing power. This is why we suggest
leaving the air control valve fully open when experimenting with a new coating
material, otherwise, it will confuse. If the air control valve is fully open
(or perhaps removed for latex spraying) then orange peel can only be one cause
– the material is too thick and must be thinned.
GRITTY FINISH
If the material is too thin, it is likely to run or be over-atomized,
producing a rough gritty finish. Try thinning the product less and spraying a
wetter coat.
FISH EYES
If you are refinishing furniture or pianos, fish eyes could become a problem.
The cause is usually silicone or oil from polish which has been liquefied by
the paint stripper that has now soaked into the bare wood. This silicone
prevents the lacquer from adhering to the wood. One way to sometimes correct
this is to seal in the silicone by misting on two or three light coats of
lacquer. Then spray on a regular wet coat. We do not recommend the use of a
product known as ‘Fish-Eye Drops’ which is essentially liquid silicone.
Silicone will only contaminate the gun even further. Anything that comes into
contact with the silicone becomes contaminated – such as; rags, aprons, bench
tops, and gloves.
SPRAY GUN USER GUIDE
NO PAINT (OR VERY LITTLE PAINT)
The air passing through the Pressure Tube 10-2000/10-2001 to pressurize the
cup is blocked. This means that either the tube itself, the check valve, or
one of the two nipples are blocked. A pipe cleaner can be used for cleaning
the hole in the nipple.
- Pressurizing tube and/or nipples are blocked – COMMON
- The cup is not tightened down sufficiently or the cup lid gasket is worn and leaking air
- The cup is empty
- The metal fluid tube is blocked with paint – RARE
- The fluid coupler is blocked with paint – RARE
UNEVEN SPRAY PATTERN
One of the holes in the air cap may be blocked. Or, the paint could be dirty
and is partially block the fluid nozzle. Remove the air cap and clean by
soaking in solvent and using a soft bristle brush or a rag. NEVER use metal
objects to clean holes in the air cap.
LEAKAGE
If paint material comes out of the fluid nozzle without pulling the trigger.
- The needle is not sitting in the fluid nozzle properly
- The needle packing may be too tight preventing the needle from moving -see page 18 needle packing
- Foreign matter trapped between the needle and fluid nozzle
- The needle or fluid nozzle could be damaged or worn
- Loose fluid nozzle
- Wrong fluid nozzle size installed
CUP LEAKS
- Oil above and below the lever to smooth the lever action
- Change gasket/diaphragm
- Leak around nipple – use Loctite to seal
- Leak around side pins – use Loctite to seal
- Leak through lid – remove nut under lid – use Loctite
THE TRIGGER IS SLUGGISH
- The Needle Packing is too tight – see LEAKAGE FROM THE NEEDLE PACKING NUT page 18
- Bent Needle
POOR SPRAY PATTERN
- Damaged needle or nozzle
- Nozzle is clogged
- Air holes in air cap clogged
- Gun too far from the surface (max. 8”/20cm)
PAINT AT THE AIR NOZZLE HOLES
- The fluid nozzle is loose and material is leaking around it – tighten with the supplied wrench
- Paint enters the gun via a pressure tube and is blown through the barrel to the air cap
GUN SPRAYS IN A PULSATING MANNER
- The needle packing has worn a little or is loose. Tighten.
- The cup is almost empty
- The cup lid is not tight – air is escaping
- The clear plastic pressure tube is leaking air – replace
- The pressure tube and/or nipple is clogged – clear or replace
EXCESSIVE OVERSPRAY
- The spray pattern size is too large for the item being sprayed
- The gun is being held too far away – should be 8” max. (20cm)
- Trigger on and off as you pass over the edges of the item
- The ‘paint’ is too thin – try thinning less
- Reduce the air by turning the air control valve to the point where overspray is minimized but the finish still looks good
- For ideal and comfortable spraying conditions, you should install an extraction fan.* If you are spraying a flammable, combustible product such as nitrocellulose lacquer, you must install an explosion-proof fan
Please check with the Local Authority having jurisdiction on this matter.
LEAKAGE FROM THE GRAVITY CUP
This occurs when there is an accumulation of cured material on the threads.
The most common cause of this is opening the cup without correctly
depressurizing the cup assembly. To correctly depressurize the cup, remove the
pressure tube from the check valve – wait for the air to escape before opening
the cup.
Should there be a build-up of cured material on the threads soften this with
the correct solvent and thoroughly brush clean with the cleaning brush
(supplied). The cup is all-nylon and is resistant to most solvents used in the
industry.
LEAKAGE FROM THE NOZZLE
This occurs when the Needle Packing Nut 10-2086 is too tight compressing the
Needle Packing 10-2085 too tightly around the needle.
Half fill the cup with water. Attach the gun to the hose and turn on the
turbine blower to pressurize the cup. Pull the trigger and release. Check the
nozzle for water spurting out.
Use the supplied wrench to GENTLY loosen the nut (1 or 2 degrees only at a
time). This is a very sensitive adjustment. Again pull the trigger and
release. Wipe away the water in between adjustments. Repeat until no water is
seen at the nozzle hole.
LEAKAGE FROM THE NEEDLE PACKING NUT
This occurs when the needle packing nut is too loose.
Half fill the cup with water. Attach the gun to the hose and turn on the
turbine blower to pressurize the cup. Use the supplied wrench to GENTLY
tighten the needle packing nut 1 or 2 degrees only. This is a very sensitive
adjustment.
-
Wipe away the water in between adjustments. Repeat until no water is seen where the needle passes through the Needle Packing
Nut 10-2086. -
It is a good idea to apply light machine oil or Vaseline to the needle shaft where it passes through the needle packing nut and work it in and out by pulling the trigger back and forth. This will lubricate the Needle Packing 10-2085.
PARTS DESCRIPTION
ITEM PART DESCRIPTION
- 10-2080 Collar
- N/A Air Cap 2
- N/A Fluid Nozzle 2
- 10-2081 Air Diffuser
- 10-2082 Diffuser Seal
- 10-2083 Air Divider Seal
- 10-2084 Air Divider
- N/A Suction Fluid Coupler 1
- 10-2085 Needle Packing
- 10-2086 Needle Packing Nut
- N/A Gravity Fluid Coupler 1
- N/A Fluid Coupler Seal 1
- N/A Gun Body
- 10-2087 Rotating Nipple Assembly
- 10-2088 Nipple
- 10-2089 Spindle Valve
- 10-2090 Valve Spring
- 10-2091 Fluid Screw Nut
- N/A Needle 2
- 10-2092 Needle Spring
- 10-2093 Fluid Adjusting Knob
- N/A Air Deflector 3
- N/A Deflector Seal 3
- N/A Control Knob Nut 3
- N/A Pattern Control Knob 3
- N/A Locking Screw 3
- N/A Handle Tube 1
- N/A Handle 1
- N/A Hose Connector 1
- 10-2094 Retaining Ring
- 10-2095 Trigger
- 10-2096 Trigger Pin
Parts marked with 1 are not removable
Parts marked with 3 are available in Kit 10-2097
Parts marked with 2 refer
TURBINE CARE & MAINTENANCE
FILTERS
-
It is important to clean or replace the filters regularly. Operating the turbine unit with clogged or dirty filters will cause the turbine to overheat and result in premature failure. QTech HVLP Turbines have either one or two filters. To remove, simply pull the filters out from filter enclosure. Wash in warm soapy water and dry before
replacing. -
All QTech filters are a friction fit. The filter must fill the entire filter enclosure.
-
Cleaning your filters regularly is essential to maintaining your QTech HVLP
-
Turbine. It is always a good idea to have a spare pair of filters on hand.
-
Re-order number for filter: 10-2049 (pack 2)
IMPORTANT NOTE
- All QTech HVLP Turbines are designed for intermittent use. When taking a break between coats or stepping aside to refill your cup, it’s good practice to turn the machine off during this time. This allows it to cool off.
- When spraying, always ensure that the turbine unit is at least 5.0m (15 feet) away from spray project and in a well ventilated area. This will prevent any overspray or debris being ingested into the turbine. Failure to do this may cause the filters to clog, resulting in damage to the internal motor.
- If you experience a problem with your turbine unit, please DO NOT try to open
and service the turbine yourself. Contact your approved dealer or Aristospray for technical assistance. If it is an issue of no power, check your power outlet. Also, try re-setting the breaker on the back of the turbine by pressing it once.
GUN HOLDER & HANDLE BAR
GUN HOLDER INSTALLATION
- The two holes on the top of the holder require the two machine screws and washers. These screws fit into threaded inserts in the metal case.
- Do not over-tighten – snug is fine.
- The single silver-coloured screw must be installed to the single hole on the side of the gun holder. Once again, please do not over-tighten this screw – snug is fine.
- If you do not intend on using the gun holder you may insert the appropriate screws (as mentioned above) to block the holes.
TURBINE HANDLEBAR INSTALLATION
Included in the box is an Allen key with four black screws and a handlebar.
Carefully position and align the handlebar over the four holes – two on each
side of the turbine case. Using the Allen key, secure the screws through the
handlebar onto the turbine case.
GUN HOLDER USE
Place the Hose Connector (base of the gun handle) over the shaft of the gun
holder as shown in the above illustration. Please ensure it is fully set down
to the base of the shaft. The spray gun will now sit stationary. The gun can
be left on the holder for any length of time. It is a convenient resting place
between spraying and ideal for filling the gravity cup.
CUP ASSEMBLIES | HOSE
SUCTION CUP
ITEM PART DESCRIPTION
10-2009 Complete assembly
-
10-2004 Cup Lid Gasket
-
10-2005 Plastic Diaphragm
-
10-2000 Pressure Tube / Check Valve
-
10-2059 Nylon Strainer (pack 5)
-
10-2007 Aluminium Cup 1000cc 10-2008 Teflon Coated Aluminium Cup 1000cc
GRAVITY CUP
ITEM PART DESCRIPTION -
10-2001 Pressure Tube / Check Valve
-
10-2074 Nylon Gravity Cup 600cc
-
10-2070 Aluminium Gravity Cup 600cc
-
10-1053 Aluminium Gravity Cup Lid 90° Fitting
-
-2058 Filter (pack 10)
NOTE
10-2001 Pressure tube/check valve & 10-2058 filter are common to both the
nylon & aluminium gravity cup assemblies
HOSES
PART DESCRIPTION
- 10-2011 Whip Hose / 6 ft / 1.8 m
- 10-2048 HVLP Super Duty Air Hose / 30 ft / 9 m
- 33 10-2010 Quick Connect Coupling (hose to gun)
- 34 10-2119 Hose Seal
- 35 10-2003 Air Control Valve
CONTACT
- QTech Global Ltd
- 1a Quillyburn Business Park
- Banbridge Road
- Dromore
- County Down
- BT25 1BY
- Email sales@qtechspray.com
- Phone
- UK 01895 276751
- ROI 0 1690 3162
- International +44 1895 276751
- www.QTechSpray.com
References
- Paint sprayers for the professional decorator. - QTechSpray
- Paint sprayers for the professional decorator. - QTechSpray
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>