XIAMEN 2AUTE-2DT24J Smart Pocket Printer Label Printer User Guide

June 1, 2024
Xiamen

XIAMEN 2AUTE-2DT24J Smart Pocket Printer Label Printer

XIAMEN-2AUTE-2DT24J-Smart-Pocket-Printer-Label-Printer-
product

Specifications

  • Power Button: On/Off control, LED indicator
  • Charging: DC adapter or USB port
  • Components: Paper Tearing Knife, USB Interface
  • APP Setting: Device management, firmware version display
  • Safety Precautions: Battery Management, Print Head Care, Charging Port Protection
  • FCC Compliance: Part 15 Rules, RF Exposure Guidelines

Product Usage Instructions:

Using Guide
To turn the device on or off, hold down the Power Button for 2 seconds. The LED indicator provides different statuses:

  • Standby / Charging completed: Slow flash
  • Charging: Fast flash
  • Supplies near end, cover open, Firmware updating, low battery, print head overheated: Fast flash
  • Charging: Recommended after full charge via DC adapter or computer USB port

Appearance and Components
The device includes components such as the Power Button, Cover Opening Button, Upper Cover, Paper Tearing Knife, and USB Interface. Be cautious of the sharp edges of the Paper Tearing Knife.

Replacing Supplies
Before installing the paper roll, tighten it properly. When replacing supplies, follow the directions in Figure 2 and ensureboth sides click into place when closing the top cover.

Safety Precautions

  • Battery Management: Unplug USB cable after charging; avoid high-temperature charging environments.
  • Print Head Care: Do not touch the print head directly after printing to prevent overheating injuries.
  • Charging Port Protection: Gently insert or unplug the USB cable to prevent damage to the charging port.

FAQ

  • Q: How do I charge the device for the first time?
    A: It is recommended to charge the device after a full charge. You can charge via a DC adapter or a computer USB port.

  • Q: How do I replace supplies properly?
    A: Tighten the paper roll before installation. Follow the directions in Figure 2 for placing supplies correctly and ensure both sides click into place when closing the top cover.

  • Q: What safety precautions should I keep in mind?
    A: Unplug the USB cable after charging to avoid battery overheating. Do not touch the print head directly to prevent injuries caused by overheating. Gently insert or unplug the USB cable to prevent damage to the charging port.

Packing List

Note: The packing items are actually based on the order.

Using Guide

Power Button Status

  • Hold down for 2 seconds to ON/OFF
  • Lighting: Standby / Charging completed
  • Slow flash: Charging
  • Fast flash: Supplies near end, cover open, Firmware updating, low battery, the print head is overheated

Charging

  • Use it for the first time after purchase
  • Recommended to use after full charge
  • Charge via DC adapter or computer USB port

LED Indicator Definitions

In use

  • Normal: always on
  • Exception: flashes slowly, view tips in the APP.

Charging process

  • Charge normally: flashes slowly
  • Full of anomalies: flashes quickly
  • Battery charged: always on

Appearance and Components

  1. Power Button
  2. Cover Opening Button
  3. Upper Cover
  4. Paper Tearing Knife
  5. USB Interface

Warning:The paper tearing knife has sharp edges and should not be touched.

Download APP
Scan the QR code below and install the App.

Connec t the device
Download Hereprint – APP, turn on Bluetooth on your phone, enter the APP, click Add Device, and connect by searching Bluetooth.

APP Setting

Simple Operation APP Setting
You can view information such as remaining power,  firmware version in device management.

Replace Supplies

XIAMEN-2AUTE-2DT24J-Smart-Pocket-Printer-Label-Printer-
\(8\)

  • With reference to figure 1, Pull the cover opening button down and open the top cover.
  • When replacing supplies, place the supplies in reference to the direction shown in figure 2.
  • Close the top cover after loading paper. Please make sure both sides click into place.

When changing supplies , do not touch the print head in case of injury caused by overheating.

Safety Precautions

Battery Overheating
Battery Management and Precautions

  • When charging is completed, please unplug the USB cable.
  • To avoid fire, do not charge at high temperature (e.g. sweating rooms, bonfire nearby, etc.).

Charger Attention
Print Head Management and Precautions
There may be damage to the print head due to improper charging.
We recommend not to use printer in high humidity or dusty areas.

Burn Hazard
Print Head Overheating
After printing, do not touch the print head directly in case of injury caused by overheating.

Charging Port Damage
Charging Precautions
Please gently insert or unplug the USB cable to prevent excessive damage to the charging port.

FCC
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference, and
  2. This device must accept any interference received, including interference that may cause undesired operation.

Warning: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit differentfrom that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna.

FCC Radiation Exposure Statement
The device has been evaluated to meet general RF exposure requirement.
The device can be used in portable exposure condition without restriction.
FCC ID :2AUTE-2DT24J

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals