XIAMEN D02 Lock Body American Deadbolt Installation Guide

XIAMEN D02 Lock Body American Deadbolt

Product Specifications

• Model: NQRE
• Compliance: FCC Part 15
• Conditions: Operation must not cause harmful interference

Product Usage Instructions

Safety Precautions

• Before using the device, carefully read all safety instructions provided in the user manual to prevent any accidents or damage.

Setup

• Ensure the device is placed on a stable surface and connected to a power source according to the manufacturer’s guidelines.

Operation

• Press the power button to turn on the device. Follow the on-screen instructions for further setup if applicable.

Maintenance

• Regularly clean the device using a soft, dry cloth. Avoid using harsh chemicals that may damage the device.

Frequently Asked Questions (FAQ):

Q: How do I reset the device?

• A: To reset the device, locate the reset button on the back and press it using a pin or paperclip for a few seconds.

Q: What should I do if the device malfunctions?

• A: If you encounter any issues, refer to the troubleshooting section in the user manual or contact customer support for assistance.

Dimension

Important Notes

1. Please read this Installation Guide carefully and contact Customer Care for any installation queries.
2. It is recommended that installation be carried out by a professional technician to prevent any potential service charges that can occur due to incorrect installation.
3. Four alkaline AA batteries (not included) are required to power the device. Non-alkaline and rechargeable batteries are “NOT RECOMMENDED”.
4. Do not remove the batteries from the lock while it is working.
5. Batteries must be replaced immediately when the lock prompts the battery is dead warning.
6. Mechanical keys are included for manual unlocking, Please store the keys in a secure location.

What’s in the Box

Note: Screws for doors with a thickness of 35 to 55 mm are included in the standard package.

Installation Diagram

Important Note

• To stabilize the Outdoor Assembly, you can use either the provided Double-sided Tape or Stud. The stud requires an additional hole to be drilled.

Installation Procedure

1. Prepare Door for Installation
2. To ensure proper installation of the smart lock, make sure the following criteria are followed:

  * Check the door status. Make sure the doorframe is aligned with the door.
  * There are no obstructions stuck in the doorframe.
  * Leave enough space for the deadbolt to extend into the doorframe when the door is locked.
2.  **Check your door/frame dimensions to make sure that they fit thefollowing measurements:**
  *  **Diameter** of Cross Bore: 55 mm
  *  **Backset:** 60 mm or 70 mm
  *  **Diameter** ofDoorHole:25 mm
  *  **Door Thickness:** 35 to 55 mm![XIAMEN-D02-Lock-Body-American-Deadbolt-fig-4](https://manuals.plus/wp-content/uploads/2024/04/XIAMEN-D02-Lock-Body-American-Deadbolt-fig-4.jpg)

2. Drill Holes on the Door
3. Place the Installation Template at the desired Cylinder height.
4. Mark for the holes to be drilled and drill the marked places.

  *  **Important Note**
  * It is not necessary to drill holes in the door. We have already provided Double­sided Tape in the kit to help with the stabilization of the lock during installation.
  * If you still want to improve stability, use the mounting template to drill the holes.

3. Install the Deadbolt
4. Adjust this Deadbolt(if needed)
5. Measure your door’s backset dimension whether 60mm or 70mm.
6. The backset is the distance from the edge of the door to the center of the hole drilled into the door.
7. You can hold the deadbolt in front of the door hole, with the deadbolt face flush against the door edge. If the slotted hole is centered in the door hole, the backset dimension is 60mm.lF not, the backset dimension is 70mm.
8. The default Backset is 60mm, but if you want to adjust the Backset to 70mm, grasp the body and twist the Faceplate as shown below:
9. Before installing, make sure that the deadbolt is in the unlocked position and that the arrow is facing upwards. (the word”TOP” faces up as indicated on the deadbolt)
10. Screw into the doorframe with Screws A.
11. Use a screwdriver to test if the deadbolt works smoothly.
12. Install the Strike Plate and Box
    • (If you have an existing strike plate installed, Skip this step)
    • Make sure that the Strike Box is aligned with the Deadbolt. Then, use the Installation Template to drill holes.
    • Align the Strike Plate and Box with the drilled holes and tighten them with Screws A.
13. Install the Exterior Assembly

There are two methods to install the Assembly.

Method 1: Installation with Stud

1. Place the Stud on the Mounting Plate of the Assembly.
2. Make sure the highlighted Spindle is in the horizontal position, as shown below.
3. Route the cable below the bolt
4. Attach the Outdoor Assembly to the door by inserting the cable through the drilled holes.

Method 2: Installation with Double-sided Tape

1. Remove the double-sided tape from the outdoor assembly’s mounting plate.
2. Make sure that the highlighted Spindle is in the horizontal position, as shown below.
3. Route the cable through the opening below the bolt.
4. Attach the Outdoor Assembly to the door by inserting the cable through the drilled holes.

Note: The method of installation with stud is more stabilized, the Installation with Double-sided Tape is the second choice.

Install the Mounting Plate

According to the previously selected Outdoor Assembly Installation method in Step 5, choose the Mounting Plate installation method.

Method 1: Installation with Stud

1. Route the cable through the hole on the Mounting Plate.
2. Place the Mounting Plate on to the door and use Screws B to secure them.

Method 2: Installation with Double-sided Tape

1. Insert the cable through the Mounting Plate’s hole.
2. Install the Mounting Plate on the door and fasten it with Screws Band Screw C.

Install the Indoor Assembly

1. Connect the cable to the port on the back of the Indoor Assembly.
2. Install the Indoor Assembly on the Mounting Plate in the proper location. Then attach the Indoor Assembly using Screw D and Screw E.

Note: No matter left or right opening direction, the knob dot must be vertical, after installing the batteries, please turn the knob dot to the horizon.

Physical Testing

1. Rotate the Knob to check if the Deadbolt works properly.
2. Insert the Key and rotate to check if the Deadbolt works properly.

Note: If the Knob or Key cannot control the Deadbolt correctly, please read the Installation Procedure carefully and re-install the lock.

Install the Batteries and Cover

1. Insert four alkaline AA batteries into the battery compartment and cover them with the battery cover.
2. Turn the KNOB to the horizontal position when the voice prompt “Di” appears and the button is solid on, then the voice “Successful” appears.
3. Enter 7 to enable Auto Re-lock Mode (if needed).

Product Overview

Important Notes

1. Please read this User Manual carefully or contact Customer Care for any queries.
2. It is recommended that installation be carried out by a professional technician to prevent any potential service charges that can occur due to incorrect installation.
3. Please make sure no strong magnetic object closes to the smart lock.
4. Four alkaline AA batteries (not included) are required to power the device. Non- alkaline and rechargeable batteries are “NOT RECOMMENDED”
5. Do not remove the batteries from the lock when it is working.
6. Batteries must be replaced immediately when the lock prompts the battery is dead warning.
7. For manual unlocking, the lock is also provided with mechanical keys. Please keep the keys in a safe place.
8. Fingerprint positioning tips: Recommended fingers: Index, middle, or ring fingers; avoid using the thumb or pinky, as it is difficult to accurately press onto the fingerprint reader using those.
   • Note: Please use the correct method when pressing your fingers onto the fingerprint reader for registration and identification.
   • Our company will assume no liability for recognition issues that may result from incorrect usage of the product. We reserve the right of final interpretation and modification concerning this point.
9. After unlocking by APP, fingerprint, or password, please do not verify again.

Usage Notice

Note: Please prepare a Phillips screwdriver and 4 AA batteries before installation. After installation, the initial status calibration and commissioning must be operated

1. In default setting, it can be unlocked Use fingerprints or mechanical key.
2. There will be a low power alarm when the voltage is below 4.8V, it can be only unlocked around 50 times, please replace it with 4 new AA batteries in time.
   • When the battery power runs out, it can be unlocked by connecting a power bank with a micro USB wire through an emergency power port. Please note the APP network function will not work in this situation.
3. Please don’t use any corrodent material to clean the lock surface.
4. Please use the mechanical key to unlock when the password and APP do not work.
   • Make sure your keys are kept in an outdoor safe place.
5. Suitable door thickness: 35~55mm.
6. Working temperature:- 25°C~55°C.

Features

1. The password capacity is 100, the first two users are administrators.
   • Please input the password as the first administrator.
2. Durable touching button.
3. Support volume adjustment(Mute/Low/High)and low power alarm.
4. Support 6-8 passwords and 16 virtual passwords.
5. Automatically open and lock the door.
6. Return or Quit Confirm or Lock.

Calibrate The Initial Status

• a. Please Stand in the room all the time when Calibrating.
• b. Reset Lock: Long press the ‘Reset’ button for 3 seconds, and restore to the factory default settings.
• C. Calibrate the Door Open Direction When the voice prompt button is always bright, turn the KNOB to the horizontal position, and the voice prompt is ‘successful’.
• Note: If calibrate failure, the button is always bright, please turn the KNOB to the horizontal position again or turn it down harder.
• d. Calibrate the Door Close Position: Close the door, and press ‘7’ to automatically calibrate the door close position.

Commissioning

• a. Please Stand in, the room all the time when commissioning.
• b. button: Short press, the bolt stretch out;
• c. Fingerprint/ Password Unlock, the bolt retract.
• d. ‘Switch’ button: Short press the bolt to stretch out or retract.
• e. KNOB: Rotate, the bolt stretch out or retract.
• f. Any way fingerprint/ password / IC card/switch button/ knob unlock, then close the door, the match will stretch out to lock automatically.
• g. Verify whether other functions including Self–lock, anti-peeping password Reset button, APP works well or not.

Device Operation

• Note: After the first hardware installation, be sure to restore the factory settings.
• Press and hold the reset button in the lower right corner of the battery compartment for 5 seconds.
• For your convenience, please add an administrator first.
• How to Add Fingerprints, Passwords, and Fobs Cards

Important Notes:

• a. For your convenience, please add an administrator first.
• b. The local input fingerprint, password, and Fobs card can all be administrators.
• c. The first three users are administrators.
• When an administrator has been added, you need to verify the administrator code when adding other users.

Press 2+ to add:

1. Add Fingerprint: Enter your fingerprint as prompted.
   • Each fingerprint needs to be entered 3 times. Note that to ensure the integrity of the fingerprint, you should enter a different part of your fingerprint each time.
2. Add Password: Enter a 6-digit password. Password registration needs to be entered 2 times.
3. Add Fobs Card: Hold the Fobs card close to the card sensing area until you hear a sound indicating success.
4. Press the key to quit adding users.

How to Delete Fingerprints, Passwords, and Fobs Cards

• Deletion of user permissions is not available on the device.
• If you intend to delete the user’s fingerprint, password, card, and other permissions, please operate on the App.
• Enable the App, click on “Settings”, then, click “Fingerprint Management Password Managent” or “Card Managent” to delete.

Other Functions

1. Normal Open Mode (when the lock is off)
   • Press “3” + to enter the Normal Open mode. (Operation timeout: 10 seconds) If you have added an administrator, it requires verification of administrator information. Press the key to quit the Normal Open mode.
2. Voice Language Switch
   • Press “4” + to switch the voice language between Chinese and English. (Operation timeout: 10 seconds)
3. Volume Adjustment
   • Press “5” + to enter the volume setting. (Operation timeout: 10 seconds).
   • Press “0” + to mute the sound;
   • Press “1” + to choose the lowest volume;
   • Press “2” + to choose low volume;
   • Press “3” + to choose normal volume;
   • Press “4” + to choose the highest volume.
4. Factory Reset
   • Method 1: Press and hold the reset button in the lower right corner of the battery compartment for 5 seconds to restore factory settings.
   • Method 2: Press “6” + to enter the factory reset after disconnecting all Bluetooth pairings. (Operation timeout: 10 seconds).
   • Note: After the TUYA App) is operated, the data entered in the app will all be invalid. (If your lock has connected.

APP Operation

Note: After the first hardware installation, be sure to restore the factory settings.Press and hold the reset button in the lower right corner of the battery compartment for 5 seconds.

Preparations

1. Download the TUYA App: Scan the following QR code to download and install the TUYA App.
2. Register Account: Registering an account is necessary before using the TUYA App for the first time. You can follow the APP prompts for user registration.

How to Connect to TUYA App

• a. Turn on the Bluetooth and location on your smartphone.
• b. Open the App and click the “+” in the upper right corner to add the device.
• c. Wake the lock, and press “1” + to enter Bluetooth pairing. (Operation timeout: 60 seconds)
• d. If the pairing fails, turn off the Bluetooth and wait a few minutes, then repeat the step1, step2, step3. You can also click the blue word” pairing mode” on the App to get more help information.

App function of control smart lock

1. Member Management: Add family members and other members
2. Wrong Password Alarm: View the wrong access code records
3. Unlocking Records: View family members’ unlocking
4. Add and delete user information for lock: fingerprint management, card management, password management
5. Change The Voice Volume
6. Obtain Dynamic Password
7. Unlock within Bluetooth range

NOTE:

1. After a battery change or power outage, other members cannot unlock the door until the administrator reconnects to the app and refreshes (connected to the App).
2. If you have connected the App, Device Operation 2+ (user management) will not be available. You can manage user information on the app.
3. A lock can only be paired with one phone, Bluetooth pairing “1 + will not work when the lock has already been paired with a phone. You can share administrator permissions with your family on the App.

FCC WARNING

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference,
2. this device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital These mits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used under the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated with a minimum 20cm distance between the radiator and your body: Use only the supplied antenna.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>