XIAMEN GMEV40CIC1B-WC Electric Vehicle AC Charger User Manual
- June 1, 2024
- Xiamen
Table of Contents
XIAMEN GMEV40CIC1B-WC Electric Vehicle AC Charger
Specifications
- Model: GMEV40CIC1B-WC
- Output Amperage: 16A, 32A, 40A, 48A
- Circuit Breaker Options: 20A, 40A, 50A, 60A
- Compliance: FCC Part 15, UL 2594, UL 2231-1, UL 2231-2, UL 2251, UL 62, UL 991, UL 1998, NFPA 70 Article 625, UL 840
Product Usage Instructions
Safety Instructions
Follow these important safety instructions:
- Avoid using extension cords with the device.
- Do not attempt to open the enclosure as there are no user-serviceable parts inside.
- Refer servicing to qualified personnel.
Design Standard
The product complies with the following design standards:
- UL 2594: Electric Vehicle Supply Equipment
- UL 2231-1: Personnel Protection Systems for Electric Vehicle (EV) Supply Circuits: General Requirements
- UL 2231-2: Personnel Protection Systems for Electric Vehicle (EV) Supply Circuits: Particular Requirements for Protection Devices for Use in Charging Systems
- UL 2251: Plugs, Receptacles and Couplers for Electric Vehicles
FAQ
- Q: Can I use an extension cord with this charger?
- A: No, it is recommended not to use an extension cord with the charger to avoid the risk of fire or electric shock.
- Q: What are the compliance standards met by this product?
- A: The product complies with FCC Part 15 and various UL standards related to electric vehicle supply equipment and personnel protection systems.
Important Safety Instructions
WARNING – This manual contains important instructions for Models:
GMEV40CIC1B-WC shall be followed during the installation, operation and
maintenance of the unit.
- Read all the instructions before using this product.
- This device should be supervised when used around children.
- Do not put your fingers into the electric vehicle connector.
- Do not use this product if the flexible power cord or EV cable is frayed, has broken insulation, or any other signs of damage.
- Do not use this product if the enclosure or the EV connector is broken, cracked, open, or shows any other indication of damage.
-
To reduce the risk of fire, connect only to a circuit provided branch circuit over-current protection per the CSA C22.1–15 Canadian Electrical Code, Part 1 (Canada) or NOM-001-SEDE Electrical installations (utility) (Mexico) or ANSI / NFPA 70 National Electrical Code (USA).
Circuit Breaker Options table
Output Amperage (A)
|
16A
|
32A
|
40A
|
48A
Circuit Breaker Options (A)| 20A| 40A| 50A| 60A
7. To avoid the risk of fire or electric shock, do not use this device with an extension cord.
8. THE SUITABILITY OF THE USE OF FLEXIBLE CORDS UNDER CE CODE, PART I, RULE 4-012, IS TO BE DETERMINED BY THE LOCAL INSPECTION AUTHORITY HAVING JURISDICTION.
9. Risk of electric shock. Do not remove the cover or attempt to open the enclosure. No user-serviceable parts inside. Refer servicing to qualified service personnel.
FCC STATEMENT
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
This device may not cause harmful interference, and this device must accept
any interference received, including interference that may cause undesired
operation.
Caution: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class A digital device, according to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used under the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
- WIFI module: Contains FCC ID:2AC7Z-ESPWROOM32D
- WIFI module: Contains IC: 21098-ESPWROOM32
To satisfy FCC RF exposure requirements, a separation distance of 20cm or more should be maintained between the antenna of this device and persons during device operation. To ensure compliance, operations at closer than this distance is not recommended.
Basic Interface
Dimensions
Design Standard
- UL 2594: Electric Vehicle Supply Equipment
- UL 2231-1: Personnel Protection Systems for Electric Vehicle (EV) Supply Circuits: General Requirements
- UL 2231-2: Personnel Protection Systems for Electric Vehicle (EV) Supply
- Circuits: Particular Requirements for Protection Devices for Use in Charging Systems
- UL 2251: Plugs, Receptacles and Couplers for Electric Vehicles
- UL 62: Flexible Cords and Cables
- UL 991: Tests for Safety-Related Controls Employing Solid-State Devices
- UL 1998: Software in Programmable Componets
- NFPA 70 Article 625: National Electrical Code, Electric Vehicle Charging System
- UL 840 (Clearance and Creepage)