XIAMEN M0BPU0 Microwave Radar Owner’s Manual
- June 1, 2024
- Xiamen
Table of Contents
XIAMEN M0BPU0 Microwave Radar
Specifications
- Model: M0BPU0
- Manufacturer: Xiamen Unique Technology Co., Ltd.
- Operating Temperature Range: -40°C to 85°C
System Overview
The Object Detection Radar System is designed to detect and inform the driver
of objects in the close proximity blind spot behind the vehicle. It alerts the
driver of potential collisions based on the manufacturer’s strategy.
Kit Contents
| No. | Item | QTY. |
|---|---|---|
| 1 | Radar sensor | 1 |
| 2 | LED display | 1 |
Harness Layout
The harness layout includes connections for the display, sensor, and external
outputs.
Volume Adjustment
- Press the setup button briefly to enter volume adjustment mode.
- The LED display will show the current volume level.
- Press the setup button to cycle through volume levels (Low, Middle, High).
- Stop pressing to save the desired volume level and exit.
Display System Settings
To configure display settings
- Press and hold the setup button for 1.5s-3.0s to switch between Imperial and Metric display.
- Continue holding the setup button for 3.0s-4.5s to enter automatic learning function settings.
- Cycle through the options by pressing the setup button and stop to save the desired setting.
Detection Range Setup
To set up the detection range
- Press and hold the setup button for 3.0s-4.5s until L0 appears on the display.
- Press the button to switch to L2 for rear sensor installation position.
- Enter learning mode and follow the progress bar for setup completion.
Safety Warning
WARNING: The Object Detection Radar System is not a substitute for
careful driving. Always be aware of surrounding pedestrians, cyclists, and
vehicles to prevent injuries and accidents.
FAQ:
Q: What should I do if the learning process fails?
A: If learning fails, the system will beep twice. Check the setup and try
again to ensure successful learning completion.
WARNING
To help prevent injuries, never use the Object Detection System as a
replacement for checking the surrounding pedestrians, cyclists and vehicles.
The Object Detection Radar System is not a replacement for careful driving.
System Overview
Object detection radar means a system to detect and inform the driver of the presence of objects in the close proximity blind-spot back of the vehicle, if deemed necessary based on manufacturer strategy, warn the driver of a potential collision.
Kit Contents
Harness Layout
Note
- If the output cable won’t be used, please wrap the cable to avoid short circuit.
- The output is positive, the Max. output voltage is no more than 5V.
System Layout
Installation
Installation height
Requirements for vertical installation angle 
Sensor fix
The radar is installed on the vehicle body with a bracket, and the vertical
installation angle is adjusted through the mounting bracket.
Function description
Self-diagnosis
Basic function
When the key is turned to ON, the front radar sensor starts to work;
When the Reverse gear is engaged, the front and rear radar sensors both work.
The LED display will provide audible and visible warnings to the driver, the
warning principles as below:
- If there’s object being detected, the output cable will provide high level voltage; if there’s no object being detected, it will output float;
- If the reverse gear is engaged, the display will show the nearest distance of rear rear-detected object;
- Display will provide audible and visible warnings:
The display will show the distance of the detected object, and provide warning beep, according to the warning section; the warning sections are equally divided into 5 stages. Take the max. detection as 10m, the warning sections will be divided as below:
Note
- Above tracing LED display figure is an alarm distance 10m as a reference.
- No.3,4,5,6 color bar alarm showing segmentation can be setup by setup tool
- No.2 color bar alarm showing segmentation is the maximum alam distance value.
Learning function
When the installation position of the radar is not at the outermost side of
the vehicle, the radar is easy to detect the accessories of the vehicle or
vehicle body, which will result in false alarm. Therefore, in order not to
make false alarm, it is necessary to enter into the learning mode to make the
radar ignore the object.
Users need to follow the following steps to realize the learning function:
- Move the vehicle to an open area and confirm that there are no obstacles other than body accessories within (a*b)m of the radar;
- a1＞4*L1，and a1＞3m；
- b1＞W1+W2，and b1＞6m；
- Power on the system and wait for the completion of system self-diagnosis;
- Constantly press the setup button for 3.0s-4.5s, the buzzer will beep once, the display will show “L0”, and enter into the automatic learning function setup mode; Release the button, and then briefly press the key to make the display shows “L2”, the system enters into the automatic learning mode, and the learning results are shown after the learning process is completed. If “LS” is shown and beeps once, the learning is successful; if “LE” is shown and beeps twice, the learning is failed.
Display setup
Detection range setup
The detection range of the sensor is shown in the drawing below. For different vehicle models and conditions, the detection area can be configurated by a handheld setup tool:
- L1: Setup for the protruding object in the front of the vehicle , the distance from the sensor installation position to the front most part of the vehicle: default value=0m;
- L2: Warning distance: default value=10m (setup range 1-50m, accuracy 0.1m);
- W1: Right side detection width: default value=2m (setup range 1-5m, accuracy 0.1m);
- W2: Left side detection width: default value=2m (setup range 1-5m, accuracy 0.1m).
FCC
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
This equipment should be installed and operated with minimum distance 30cm
between the radiator& your body.
EUT Operating Temperature Range: -40℃~85℃
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>