MOUNT-IT MI-3880B-G10 Tablet Countertop Stand Instruction Manual

: June 1, 2024
: Mount-It

**MOUNT-IT MI-3880B-G10 Tablet Countertop Stand Instruction Manual

**

Thank you for choosing Mount-It.

Read the entire instruction manual before you start installation and assembly. If you have any questions regarding any of the instructions or warnings, please contact Mount-it! for assistance.

CAUTION: Use with products heavier than the rated weights indicated may result in instability causing possible injury.

Please closely follow the assembly instructions. Improper installation may result in damage or serious personal injury.
Safety gear and proper tools must be used. This product should only be installed by professionals.
This product is designed to be installed on solid concrete walls, masonry walls or wood stud walls.
Make sure that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.
Use the mounting screws provided and DO NOT OVER TIGHTEN mounting screws.
This product contains small items that could be a choking hazard if swallowed. Keep these items away from children.
This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.

IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installation. If any parts are missing or faulty, contact Mount-It! for a replacement.

MAINTENANCE

Check that the product is secure and safe to use at regular intervals (at least every three months).

Mount and Accessories

A (x1) Anti-Theft Tablet Case
B (x1) Standing Base
C (x1) Base
D (x4) Rubber pad
E (x1) Base Connector
F (x4) ST6.3×55
G (x4) Concrete Anchor
H (x1) Key
I (x4) M5x6
J (x4) M8x20
K (x1) Low Profile Base
L (x1) M8x45 Grommet Bolt
M (x1) Grommet Washer
N (x4) Grommet Washer
O (x4) M5
P (x4) M5x12
Q (x4) M4x12
R (x4) ST4.8×30
T1 (x1) Tablet Adapter 1
T2 (x1) Tablet Adapter 2
T3 (x1) Tablet Adapter 3
U (x1) Wrench
W (x1) 5mm Hex Wrench

Check carefully to make sure there are no missing or defective parts. Some hardware provided may not be used. Use the correct mounting hardware suitable for your installation.

CHOKING HAZARD. Package includes small parts.
Not for children under 3 years. Adult supervision is required.

Missing Parts? Call us at 855-925-5668 and we will ship replacement parts free of charge.

DIMENSIONS & WEIGHT CAPACITY

Rated weight capacity is 2.2lbs for the mount.

Caution:
Ensure all mounting surfaces are capable of holding the weight of your mount.
DO NOT EXCEED MAXIMUM LISTED WEIGHT CAPACITY.
SERIOUS INJURY OR PROPERTY DAMAGE MAY OCCUR!
Installation

Standing Base Option

Peel the backing off the Rubber Pads (#D) and place them near each corner of the Standing Base (#C).
Place the pads on the bottom side which has the recessed indentations.

Attach the Base

Attach the Column (#B) to the Standing Base (#C) through the Base Connector (#E) using Bolts (#J) as shown.

Location and Use Options.

Counter top Use

The stand may be placed directly on a countertop or tabletop for use or can be secured following the instructions in the next steps.

Wood Surface Installation

To secure the stand base to a wood surface use a 3/16” bit and drill holes to a depth of 2.2” and secure the stand base using 2x Lag Screws (#F). Do not over tighten.

Note: Ensure the mounting surface is thick enough to accommodate the length of the Lag Screws.
Wood Surface Installation

Concrete Surface Installation

To secure the stand base to a concrete surface, use a 3/8” Bit and drill holes to a depth of 2.4”. Clear any dust and debris from the holes and insert 2x Concrete Anchors (#G). Secure the stand base using 2x Lag Screws (#F). Do not over tighten.
Note: Ensure the mounting surface is thick enough to accommodate the length of the Lag Screws.

Low Profile Base Option

Attach the Column (#B) to the Low Profile Base (#K) through the Base Connector (#E) using Bolts (#J) as shown.

Wood Surface Installation

To secure the stand base to a wood surface, use a 3/16” bit and drill holes to a depth of 2.2” and secure the stand base using 4x Lag Screws (#F). Do not over tighten.
Note: Ensure the mounting surface is thick enough to accommodate the length of the Lag Screws.

Concrete Surface Installation

To secure the stand base to a concrete surface, use a 3/8” Bit and drill holes to a depth of 2.4”. Clear any dust and debris from the holes and insert 4x Concrete Anchors (#G). Secure the stand base using 4x Lag Screws (#F). Do not over tighten.
Note: Ensure the mounting surface is thick enough to accommodate the length of the Lag Screws.

Grommet Installation

To install the stand to a desktop or tabletop through a grommet hole, place the mount over the hole and attach it from the bottom using Grommet Bolt (#L) and Grommet Washer (#M). If a grommet hole needs to be installed, use a 0.3-0.4” (8-10mm) drill bit to drill a hole in the desired location.
Note: The Bolt (#L) provided will only accommodate a surface thickness of ≦1.35”.

Open the Tablet Case

To open the Tablet Case (#A) insert the Key (#H) and turn counterclockwise to unlock(clockwise to lock.)

Attach the Tablet Case to the Column

Attach the back half of the Tablet Case to the end of the column using Bolts (#I) through the 4 bolt holes on the interior of the Case in the orientation shown here.
Optionally the tablet enclosure can be attached to a 75x75mm VESA mount. Attach the back half of the Tablet Case to the VESA mount using Bolts (#P), Washers (#N), and secured on the opposite end by Nuts (#O).

Select the Tablet Adapter

Select the Tablet Adapter (#T1, T2, T3) for your tablet (see the table below for compatibility) and attach it over the tablet inside the case using the 4 Bolts (#Q). Before fully tightening the bolts, center the tablet in the adapter if needed by squeezing the tabs on the clamps and adjusting them left or right.

Insert the Tablet

Select the appropriate Tablet Adapter for your tablet by referencing the compatibility guide below.

T1: No home button access.
iPad Pro (10.5″),
iPad Air (10.5″),
iPad 9(10.2″),
iPad 8(10.2″),
iPad 7(10.2″)
Insert the Tablet

T2: Home button access present.
iPad Pro (10.5″),
iPad Air (10.5″),
iPad 9(10.2″),
iPad 8(10.2″),
iPad 7(10.2″)
Insert the Tablet

T3: Front facing camera cutout on the side.
iPad Pro (11″),
iPad Air (10.9″),
iPad10(10.9″)
Insert the Tablet

Tablet Adapter (#T2) can be used with the preinstalled soft button cover to allow for the tablet home button to be pressed, or it may be removed and replaced with the hard Button Cover (#X) which will prevent the tablet home button from being pressed.

Lock the Case

Insert the key into the lock and turn the key clockwise to lock the case.

Viewing Angle Adjustment

If the use of the tablet camera is required, ensure the camera is visible through the hole on the rear of the case.
Adjust the viewing angle of the tablet by loosening the bolt shown here behind the tablet case using Hex Wrench (#V). Tilt the tablet to the desired viewing angle then tighten the bolt back down.

Final Adjustments

The tablet case can be rotated 90 degrees to alternate between landscape and portrait orientation and can be tilted up to 75 degrees forward for a variety of viewing angles.

Optional Wall Mount Instructions

A. Concrete/Stone Installation Option – 4 Screws

Using a bubble level to ensure a straight installation, hold the anti-theft case against the wall in the desired location and use a pencil to mark the wall through the 4 bolt holes in the case. Note: This may also be rotated 90° to install in landscape orientation.
Remove the case from the wall and drill holes in the marked locations using a ¼” (6mm) drill bit to a depth of 1.3” (35mm). Insert Concrete Anchors (#S) into the holes.
Attach the tablet case to the wall using Lag Screws (#R) and tighten until secure. Do not over tighten.

Note: For a 2 screw installation option, follow the next step using a ¼” drill bit and 1.3” drill depth, and the use of concrete anchors (#S).
Optional Wall Mount Instructions

Wood Stud Installation Option – 2 Screws

Using a bubble level to ensure a straight installation, hold the anti-theft case against the wall in the desired location and use a pencil to mark the wall through the teardrop shaped bolt hole indicated here, and mark the middle of the horizontal slot below.
Remove the case from the wall and drill holes in the marked locations using a 7/50” (3.5mm) drill bit to a depth of 1.2” (30mm).
Install Lag Screw (#R) to the top hole only leaving a gap of approximately ¼” between the wall and the bottom of the screw head.
Hang the case onto the partially installed screw through the teardrop shaped hole. Slide the case down so that the screw is in the smaller end of the hole, check the level of the case again and install the lower lag screw.

Note: This installation option is compatible with concrete/stone surfaces using the same process but with a¼” drill bit and 1.3” drill depth.
Wood Stud Installation Option