fein BLK1.3TE Nibbler for Trapezoidal Instruction Manual
- June 13, 2024
- Fein
Table of Contents
BLK1.3TE Nibbler for Trapezoidal
Instruction Manual
BLK1.3TE Nibbler for Trapezoidal
BLK1.3TE ()/BLK1.3CSE ()/BLK1.6E ()/BLK1.6LE ()/BLK2.0E ()
7 232 …/7 232 …/7 232 …/7 232 …/7 232 …**
| | BLK1.3TE ()| BLK1.3CSE ()| BLK1.6E ()| BLK1.6LE
()| BLK2.0E ()**
---|---|---|---|---|---|---
| | 7 232 ..| 7 232 ..| 7 232 ..| 7 232 ..| 7 232 ..
P1| W| 350| 350| 350| 350| 350
P2| W| 210| 210| 210| 210| 210
n0| /min| 1000–1800| 1000–1800| 800–1500| 800–1500| 500–1000
nS| m/min| 2,3| 2,3| 1,9| 2,7| 1,0
Fe 400| mm| 1,3| 1,3| 1,6| 1,6| 2,0
Fe 600| mm| 0,8| 0,8| 1,0| 1,0| 1,5
Fe 800| mm| 0,6| 0,6| 0,7| 0,7| 1,0
Al 250| mm| 2,0| 2,0| 2,5| 2,5| 2,5
| mm| 19,0| 19,0| 22,0| 24,0| 18,0
| mm| 25,0| 15,0| 30,0| 65,0| 4,0
| kg| 1,75| 1,75| 1,8| 1,9| 1,8
LpA| dB| 88,5| 88,5| 90,2| 90,2| 89,9
KpA| dB| 3,0| 3,0| 3,0| 3,0| 3,0
LwA| dB| 99,5| 99,5| 101,2| 101,2| 100,9
KwA| dB| 3,0| 3,0| 3,0| 3,0| 3,0
LpCpeak| dB| 107,1| 107,1| 114,4| 114,4| 112,6
KpCpeak| dB| 3,0| 3,0| 3,0| 3,0| 3,0
ah| m/s²| 7,6| 10,0| 10,3| 4,1| 9,0
Ka| m/s²| 1,5| 1,5| 1,5| 1,5| 1,5
Translation of the Original Instructions.
Symbols, abbreviations and terms used.
| Symbol, character | Explanation |
|---|---|
| Make sure to read the enclosed documents such as the Instruction Manual and |
the General Safety Instructions.
| Observe the instructions in the text or graphic opposite!
| Observe the instructions in the text or graphic opposite!
| General prohibition sign. This action is prohibited.
| Before commencing this work step, pull the mains plug out of the socket.
Otherwise there will be danger of injury if the power tool should start
unintentionally.
| Use eye protection during operation.
| Use ear protection during operation.
| Use protective gloves during operation.
| Gripping surface
| Confirms the conformity of the power tool with the directives of the
European Community.
| Confirms the conformity of the power tool with the directives of Great
Britain (England, Wales, Scotland).
WARNING| This sign indicates a possible dangerous situation that could
cause severe or fatal injury.
| Worn out power tools and other electrotechnical and electrical products
should be sorted separately for environmental-friendly recycling.
| Switching on
| Switching off
| Product with double or reinforced insulation
| Steel
| Aluminium
| Plastic
| Low stroke rate
| High stroke rate
()| may contain numbers and letters
(Ax – Zx)| Marking for internal purposes
Character| Unit of measurement, international| Unit of
measurement, national| Explanation**
---|---|---|---
P1| W| W| Power input
P2| W| W| Output
n0| /min, min, rpm, r/min| rpm| Stroke rate at no-load
nS| m/min| m/min| Cutting speed
U| VV| VV| Rated voltage
f| Hz| Hz| Frequency
M…| mm| mm| Size of metric thread
Ø| mm| mm| Diameter of a round part
Fe 400| mm| mm| Max. work-piece thickness for steel with up to 400 N/mm²
Fe 600| mm| mm| Max. work-piece thickness for steel with up to 600 N/mm²
Fe 800| mm| mm| Max. work-piece thickness for steel with up to 800 N/mm²
Al 250| mm| mm| Max. work-piece thickness for aluminium with up 250 N/mm²
| mm| mm| Diameter of pilot-drill for inside cut-outs
| mm| mm| Min. inside curve radius
| kg| kg| Weight according to EPTA-Procedure 01
LpA| dB| dB| Sound pressure level
LwA| dB| dB| Sound power level
LpCpeak| dB| dB| Peak sound pressure level
K…| | | Uncertainty
a| m/s²| m/s²| Vibrational emission value according to EN 62841 (vector sum of
three directions)
ah| m/s²| m/s²| Vibrational emission value
| m, s, kg, A, mm, V, W, Hz, N, °C, dB,
min, m/s²| m, s, kg, A, mm, V, W, Hz, N, °C, dB,
min, m/s²| Basic and derived units of measurement from the international
system of units SI.
For your safety.
WARNING
Read all safety warnings and all instructions. Failure to follow the warnings
and instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
Do not use this power tool before you have thoroughly read and completely
understood this Instruction Manual and the enclosed “General Safety
Instructions” (document number 3 41 30 465 06 0). The documents mentioned
should be kept for later use and enclosed with the power tool, should it be
passed on or sold.
Please also observe the relevant national industrial safety regulations.
Intended use of the power tool:
Hand-guided nibbler for cutting sheet metal, cut-outs and tight curves in
weather-protected environments without water supply using the application
tools and accessories recommended by FEIN.
Special safety instructions.
Use auxiliary handle(s), if supplied with the tool. Loss of control can cause
personal injury.
Wear personal protective equipment. Depending on application, use face shield,
safety goggles or safety glasses. Where appropriate, wear dust mask, hearing
protectors, gloves and workshop apron capable of stop-ping small abrasive or
workpiece fragments. The
eye protection must be capable of stopping flying debris generated by various
operations. The dust mask or respirator must be capable of filtrating
particles generated by your operation. Prolonged exposure to high inten-sity
noise may cause hearing loss.
Secure the work piece firmly. A work piece that is gripped tightly in a
clamping device or vice, is more secure than if held by hand.
Do not rivet or screw any name-plates or signs onto the power tool. If the
insulation is damaged, protection against an electric shock will be
ineffective. Adhesive labels are recommended.
Do not use accessories which are not specifically designed and recommended by
the power tool manufacturer. Safe operation is not ensured merely because an
accessory fits your power tool.
Clean the ventilation openings on the power tool at regular intervals using
non-metal tools. The blower of the motor draws dust into the housing. An
excessive accumulation of metallic dust can cause an electrical hazard.
Before putting into operation, check the mains connection and the mains plug
for damage.
Recommendation: The tool should always be supplied with power via a residual
current device (RCD) with a rated current of 30 mA or less.
Hand/arm vibrations
The vibration emission level given in this information sheet has been measured
in accordance with a standardised test given in EN 62841 and may be used to
compare one tool with another. It may be used for a preliminary assessment of
exposure.
The declared vibration emission level represents the main applications of the
tool. However, if the tool is used for different applications, with different
accessories or poorly maintained, the vibration emission may differ. This may
significantly increase the exposure level over the total working period.
An estimation of the level of exposure to vibration should also take into
account the times when the tool is switched off or when it is running but not
actually doing the job. This may significantly reduce the exposure level over
the total working period.
Identify additional safety measures to protect the operator from the effects
of vibration such as: maintain the tool and the accessories, keep the hands
warm, organisation of work patterns.
Operating Instructions.
**** Guide the power tool toward the work piece only when switched on.
While cutting, hold the power tool as upright as possible to the work-piece
surface.
Guide the power tool uniformly and with light feed in the cutting direction.
Excessive feed reduces the tool life of the application tools.
Do not cut steel sheets where welded. Do not cut layered sheets exceeding the
max. work-piece thickness.
To increase the tool life of punch and die, it is recommended to apply a
lubricating agent alongside the intended cutting line:
- For cuts in steel sheet: Cutting paste or cutting oil,
- For cuts in aluminium: Petroleum.
For inside cuts, a pilot hole is required; see “Technical Data” for diameters.
Do not switch the power tool off until after having removed it from the
cutting path.
The symptom for worn punches and dies are a clearly increased feed force at
lower working progress.
BLK1.3TE ()/BLK1.3CSE ()/BLK1.6E ()/BLK1.6LE (): Punch and die cannot
be reground.
BLK2.0E (**): The punch – not the die – can be reground as long as the length
of the reground punch does not fall below the minimum die length.
| Die | Minimum punch length |
|---|---|
| BLK2.0E (**): | |
| 3 13 09 040 00 2 | 45 mm |
BLK2.0E (): For template cuts, the template is traced via the lower
cylindrical part of the punch guide. The clearance between template and the
actual cutting edge is 2.5 mm.
The template should be at least 2 mm thick; the total thickness of template
and work piece may not exceed 5.5 mm.
BLK1.6E (): For cutting deep-channel trapezoidal sheet metal, the optionally
available profile set 160 can be mounted. (see page 9)
Repair and customer service.
When working metal under extreme operating conditions, it is possible for
conductive dust to settle in the interior of the power tool. The total
insulation of the power tool can be impaired. Blow out the interior of the
power tool via the ventilation slots frequently with dry and oil-free
compressed air, and connect a residual current device (RCD) on the line side.
Lightly grease the sliding surfaces between die holder and punch.
Products that have come into contact with asbestos may not be sent in for
repair. Dispose of products contaminated with asbestos according to the
applicable country-specific regulations for such disposal.
When the machine’s power supply cord is damaged, it must be replaced by the
manufacturer or their representative.
If required, you can change the following parts yourself: Application tools
Warranty and liability.
The warranty for the product is valid in accordance with the legal regulations
in the country where it is marketed. In addition, FEIN also provides a
guarantee in accordance with the FEIN manufacturer’s warranty declaration.
The delivery scope of your power tool may include only a part of the
accessories described or shown in this Instruction Manual.
Declaration of conformity.
This CE declaration is only valid for European Union and EFTA (European Free
Trade Association) countries and only for products intended for the EU- or
EFTA market. After placing the product on the EU market the UKCA mark loses
its mark validity.
The UKCA declaration is only valid for the Great Britain market (England,
Wales and Scotland) and only for products intended for the Great Britain
market. After placing the product on the Great Britain market the CE mark
loses its mark validity.
FEIN declares itself solely responsible for this product conforming with the
relevant provisions given on the last page of this Instruction Manual.
Technical documents at: C. & E. Fein GmbH,
D-73529 Schwäbisch Gmünd
Environmental protection, disposal.
Packaging, worn out power tools and accessories should be sorted for
environmental-friendly recycling.
This CE declaration is only valid for European Unionand EFTA (European Free Trade Association) countries and only for products intended for the EU- or EFTA market. After placing the product on the EU market the UKCA mark loses its mark validity.
DIN EN 62841-1:2015 + AC:2015
DIN EN 62841-2-8:2016
DIN EN 55014-1:2017 + A11:2020
DIN EN 55014-2:2015
DIN EN 55014-2:1997+A1:2001+
A2:2008+AC:1997
DIN EN 61000-3-2:2014
DIN EN 61000-3-2:2019
DIN EN 61000-3-3:2013+A1:2019
2006/42/EG, 2014/30/EU, 2011/65/EU
****i. V. S. Böhm
Director of Quality
Management| i. V. Dr. M. Hergesell
Director of Product
Development
---|---
Schwäbisch Gmünd-Bargau, 28.05.2021
The UKCA declaration is only valid for the Great Britain market (England,
Wales and Scotland) and only for products intended for the Great Britain
market. After placing the product on the Great Britain market the CE mark
loses its mark validity.
BS EN 62841-1:2015 + AC:2015
BS EN 62841-2-8:2016
BS EN 55014-1:2017 + A11:2020
BS EN 55014-2:2015
BS EN 55014-2:1997+A1:2001+A2:2008+AC:1997
BS EN 61000-3-2:2014
BS EN 61000-3-2:2019
BS EN 61000-3-3:2013+A1:2019
Suppl y of Machinery Regulations 2008,
EMC Regulation 2006, The Restriction of the Use of Certain Hazardous
Substances ln ectrical and Electronic Equipment Regulations 2012
****i. V. S. Böhm
Director of Quality
Management| i. V. Dr. M. Hergesell
Director of Product
Development
---|---
Schwäbisch Gmünd-Bargau, 28.05.2021
C. & E. Fein GmbH
Hans-Fein-Straße 81
73529 Schwäbisch Gmünd-Bargau, Germany
www.fein.com 34101334060
3 41 01 334 06 0. 2023-05-25.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>