MOUNT-IT MI-4222 Ultra Slim and Heavy Duty TV Wall Mount Instruction Manual
- June 1, 2024
- Mount-It
Table of Contents
Installation Manual
SKU: MI-307
Please scan this QR code
to visit the product page.
ULTRA-SLIM & HEAVY-DUTY TV WALL MOUNT
HAVE QUESTIONS?
Monday – Friday from 8:00am – 4:00pm PST
support@mount-it.com 855-925-5668 www.mount- it.com
Thank you for choosing Mount-It!
Read the entire instruction manual before you start
installation and assembly. If you have any questions regarding any of the
instructions or warnings, please contact Mount-It! for assistance.
CAUTION: Use with products heavier than the rated weights indicated may result in instability causing possible injury.
- Please closely follow the assembly instructions. Improper installation may result in damage or serious personal injury.
- Safety gear and proper tools must be used. This product should only be installed by professionals.
- This product is designed to be installed on solid concrete walls, masonry walls or wood stud walls.
- Make sure that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.
- Use the mounting screws provided and DO NOT OVER TIGHTEN mounting screws.
- This product contains small items that could be a choking hazard if swallowed. Keep these items away from children.
- This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.
IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installation. If any parts are missing or faulty, contact Mount-It! for a replacement.
MAINTENANCE: Check that the product is secure and safe to use at regular intervals (at least every three months).
Mount and Accessories
A (x1) B (x1)
Wall Mount VESA Bracket
C (x1) D (x1)
VESA Bracket Bubble Level
E (x1) F (x1)
10mm 5mm
Wrench Hex Wrench
TV Mounting Hardware
M-A (x4) M-B (x4) M-C (x4)
M6x14 M8x16 M6x30
M-D (x4) M-E (x4)
M8x35 D8
M-F (x4) M-G (x4)
∅15x∅8×5 ∅15x∅8×15
5mm Spacer 15mm Spacer
Wall mounting hardware
W-A (x6) W-B (x6)
ST6.3×55 ∅10×45
Lag Screw Concrete Anchor
W-C (x6)
D6
Check carefully to make sure there are no missing or defective parts. Some hardware provided may not be used. Use the correct mounting hardware suitable for your installation.
CHOKING HAZARD. Package includes small parts.
Not for children under 3 years. Adult supervision is required.
Missing Parts? Call us at855-925-5668 and we will ship replacement parts free of charge.
DIMENSIONS & WEIGHT CAPACITY
Rated weight capacity is 165lbs for
the mount.
Caution:
Ensure all mounting surfaces are capable of holding the weight of your mount.
DO NOT EXCEED MAXIMUM LISTED WEIGHT CAPACITY.
SERIOUS INJURY OR PROPERTY DAMAGE MAY OCCUR!
Step 1
Wood Stud Installation Option
-
Use a stud finder to locate the center of the studs and hold Wall Mount(#A) to the wall in the desired mounting location.
-
Place the Bubble Level (#D) centered on the top of the Wall Mount (#A) and ensure that the mount is level.
-
Mark the center of the studs through the mount as shown.
-
Remove the Mount from the wall and drill holes in the marked locations using a 3/16″ drill bit (4.5mm) to a depth of 2.2″ (55mm).
-
Hold the Wall Mount (#A) to the wall over the holes, check the level once again, and install the 4 Lag Screws (#W-A) and Washers (#W-C) then tighten until secure.
Step 2
Concrete/Brick Installation Option
-
Hold the Wall Mount(#A) to the wall in the desired mounting location.
-
Place the Bubble Level (#D) centered on the top of the Wall Mount (#A) and ensure that the mount is level.
-
Mark the center of the holes through the mount in the locations shown.
-
Remove the Mount from the wall and drill holes in the 6 marked locations using a 3/8″ drill bit (10mm) to a depth of 2.4″ (60mm).
Note: Do not drill mounting holes into mortar (such as between bricks or stones) only drill and install into solid stone or concrete surfaces.
- Clear dust or debris from the holes and insert the Concrete Anchors (#W-B) fully until flush with the wall. Hold the Wall Mount (#A) to the wall over the holes, check the level once again, and install the 6 Lag Screws (#W-A) and Washers (#W-C) then tighten until secure.
Attaching the VESA Brackets to the TV
- Select the appropriate size mounting bolt (Select one size #M-A, M-B, M-C, or M-D) and washer (M-E) for your display’s mounting holes and verify the length of the VESA bolt is not too long. If you are unsure of the correct bolt size for your display refer to your display’s user manual or contact the display’s manufacturer for sizing information. If necessary, use the included spacers (#M-F, M-G) between the mount and the screen as shown above to adjust the length of the mounting bolt. Multiple spacers can be used in combination to achieve the desired bolt depth.
- Attach the Right and Left VESA Brackets (#B, C) to the TV as shown using the selected bolts. Ensure that the two nuts on the side of the VESA Brackets are facing toward the outside edge of the TV or you will be unable to properly adjust the tilt of the screen.
- Too long
- Too short
Step 3
Hang the TV on the Wall Mount
- It is recommended that you use the assistance of a second person for this step. Hang the TV on the wall mount as shown so that the top of the VESA brackets hook onto the top of the wall mount, then swing the bottom of the TV down until the latches on the lower end of the brackets click into place. Attach the pull cords to the wall mount to keep them concealed behind the screen.
- Tighten the bolts indicated in the magnification bubble #1 to adjust the level of the screen by tightening the bolt on the side that needs to be raised and loosen the bolt on the opposite side if it needs to be lowered. These bolts may also prevent the mount from being easily lifted off the wall mount. Loosen these bolts if they are interfering with the removal of the tv from the mount.
- Partially loosen the upper nut indicated in the magnification bubble #2 on both VESA brackets to adjust the tilt of the screen. Once the desired tilt is achieved tighten the bolts back down to prevent further movement.
Note: Attach the magnetic pull strap to a metal surface on the mount to his the strap when not in use
-
To remove the TV from the wall mount, pull down on the pull cords to release the latches, pull the base of the TV away from the wall, then lift the TV up and off of the wall mount.
-
-
Visit us at www.mount-it.com for product registration and warranty information.
Our US based customer service team is standing by to answer any questions you have about your Mount-It! product.
Available by phone Monday – Friday from 8:00am to 4:00pm PST.
Chat live with an agent on our website!
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>