MOUNT-IT MI-1765KB Tray for Wall or Pole Mounting Instruction Manual

: May 15, 2024
: Mount-It

Installation Manual

SKU: MI-1765KB

Please scan this QR code to visit the product page.

MONITOR MOUNT WITH WALL MOUNT PLATE, CLAMP AND KEYBOARD TRAY

? HAVE QUESTIONS?

Monday – Friday from 8:00am – 4:00pm PST

support@mount-it.com (855) 925-5668

www.mount-it.com

Thank you for choosing Mount-It!

Read the entire instruction manual before you start installation and assembly. If you have any questions regarding any of the instructions or warnings, please contact Mount-It! for assistance.

CAUTION: Use with products heavier than the rated weights indicated may result in instability causing possible injury.

Please closely follow the assembly instructions. Improper installation may result in damage or serious personal injury.
Safety gear and proper tools must be used. This product should only be installed by professionals.
This product is designed to be installed on solid concrete walls, masonry walls or wood stud walls.
Make sure that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.
Use the mounting screws provided and DO NOT OVER TIGHTEN mounting screws.
This product contains small items that could be a choking hazard if swallowed. Keep these items away from children.
This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.

IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installation. If any parts are missing or faulty, contact Mount-It! for a replacement.
MAINTENANCE: Check that the product is secure and safe to use at regular intervals (at least every three months).

Mount and Accessories

| |
---|---|---

A (x1)
Spring Arm

| B (x1)
Wall Mount Plate|

C (x2)
Decorative Cover

| |

D (x1) 3mm
Hex Wrench

| E (x1) 5mm
Hex Wrench|

F (x1)
Pole Clamp

| |

G (x2) M8x65
Alternate Bolt

| H (x1)
Wrench|

I (x4)
M4 Nut

| |

J (x1)
Mousepad

| K (x1)
Keyboard Tray|

M-A (x4)
M4x12

| |

M-B (x4)
M5x12

| M -C (x4)
D5|

W-A (x2) ST6.3×55
Lag Screw

|

W-B (x2) ∅10×45
Concrete Anchor

|

W-C (x2)
D6

Check carefully to make sure there are no missing or defective parts. Some hardware provided may not be used. Use the correct mounting hardware suitable for your installation.

CHOKING HAZARD. Package includes small parts.
Not for children under 3 years. Adult supervision is required.

Missing Parts? Call us at (855) 925-5668 and we will ship replacement parts free of charge.

DIMENSIONS & WEIGHT CAPACITY

Rated weight capacity is 4.4lbs~15.4lbs for the mount.
Caution:
Ensure all mounting surfaces are capable of holding the weight of your mount.
DO NOT EXCEED MAXIMUM LISTED WEIGHT CAPACITY.
SERIOUS INJURY OR PROPERTY DAMAGE MAY OCCUR!

Step 1

Step 1a-1

A. Wood Stud Mounting Option

With a stud finder locate the stud and center the Wall Mount Plate (#B) on the stud at the desired height. Using a bubble level to ensure straightness mark the center of the mounting holes with a pencil.
Use a 3/16” drill bit and drill on the marked locations to a depth of 2.2”. Secure the Wall Mount Plate (#B) to the wall using Lag Screws (#W-A) and Washers (#W-C). Tighten the screws until secure.

B. Concrete/Brick Mounting Option

Using a bubble level to ensure straightness hold the Wall Mount Plate (#B) to the desired location on the wall and mark the center of the mounting holes with a pencil.
Use a 3/8” drill bit and drill on the marked locations to a depth of 2.4”. Clear any dust and debris from the holes and insert the Concrete Anchors (#W-B). Secure the Wall Mount Plate (#B) to the wall using Lag Screws (#W-A) and Washers (#W-C). Tighten the screws until secure.

Step 1a-2

Insert Decorative Covers

Insert the Decorative Covers (#C) into each of the bolt holes.

Step 1b

Pole Clamp Mounting Option

Attaching the Pole Clamp (Pole Diameters Between 1.1″-1.8″)

Using Hex Wrench (#E) loosen the two bolts on the Pole Clamp (#F) until the clamp opens wide enough to slide onto the pole.
Move the Clamp to the desired height and tighten the bolts back down until secure.

Attaching the Pole Clamp (Pole Diameters Between 1.8″-2.4″)

Using Hex Wrench (#E) remove the two bolts from the Pole Clamp (#F) and replace them with the Alternate Bolts (#G). After installing the alternate bolts, adjust the width of the clamp to be slightly larger than the pole.
Move the Clamp to the desired height and tighten the bolts back down until secure.

Step 2

Attach the Spring Arm to the Mount

WARNING
STORED ENERGY

The monitor arm is shipped compressed and under tension.
When cutting the cable tie firmly hold and brace both parts using your hands as shown or ask for the assistance of another person.
Failure to follow this process may result in personal injury or property damage.
- Place the end of the Spring Arm (#A) onto the end of the Wall Mount or Pole Mount. Tighten the bolt on the back of the Spring Arm to secure the arm to the mount.

Step 3

Step 3a-1

Attach the Keyboard Tray

Attach the Keyboard Tray (#K) to the end of the Spring Arm (#A) using Bolts (#M-A). Secure the bolts on the opposite side using Washers (#M-C) and Nuts (#I).
Place the Mousepad (#J) on the Keyboard Tray.

Step 3a-2

Cable Management

Cables can be run through the cable management clips on the underside of the spring arm.

Step 3b-1

Optional Monitor Instructions: Install the Top Bolts to the Monitor

Select the appropriate size mounting bolt (#M-A, M-B)for your display’s mounting holes and verify the length of the VESA bolt is not too long. If you are unsure of the correct bolt size for your display refer to your user manual or contact the monitor manufacturer for sizing information.
After selecting the appropriate bolt install the top two bolts and washers (#M-C) to the monitor leaving a gap of approximately 0.1” (3mm).

Step 3b-2

Attaching the Monitor

Hang the monitor onto the top of the VESA plate as shown.
Install the lower two bolts and washers (#M-C) through the lower holes. Tighten all 4 bolts until secure, do not over tighten.

Step 4

Final Adjustments

Cables can be run through the cable management clips on the underside of the spring arm.

CAUTION: This monitor mount utilizes a mechanical spring assembly that does not require tension adjustments to balance the weight of the monitor. Do not loosen the spring cover bolts. Removing the cover will detach the spring and it will be unable to be reattached. Any adjustment to these parts will cause irreversible damage to the monitor arm.

The viewing angle can be adjusted in the range of -45° to +90°, and the screen can be rotated 360°. Each joint can swivel left or right for alternate viewing angles.

Note: Adjust to the desired angle then tighten the screws using the tool as shown, alternating from each screw as you tighten them.

Visit us at www.mount-it.com for product registration and warranty information.

Our US based customer service team is standing by to answer any questions you have about your Mount-It! product.
support@mount-it.com

Available by phone Monday – Friday from 8:00am to 4:00pm PST.
(855) 925-5668

Chat live with an agent on our website!
www.mount-it.com