MOUNT-IT MI-7993 Folding Wall Mounted Shelf Instruction Manual

MOUNT-IT MI-7993 Folding Wall Mounted Shelf

Product Specifications

• Model: MI-7993 / MI-7993W
• Type: Folding Wall-Mounted Shelf
• Weight Capacity: 33lbs
• Dimensions: 15.6 inches x 15 inches x 45 inches

Product Usage Instructions

Mount and Accessories
The package includes left and right shelves, a middle shelf, folding arm mounts, shelf connectors, bolts, lag screws, and concrete anchor screws.

Check for Parts
Make sure there are no missing or defective parts. Some hardware provided may not be used. Ensure you use the correct mounting hardware suitable for your installation.

Safety Precautions

Choking Hazard: The package includes small parts. Not suitable for children under 3 years. Adult supervision is required.
If you have missing parts, contact us at 855-925-5668 for free replacement parts.

Installation Steps

1. Step 1: Unfold the Arms
2. Step 2: Connect the Shelf Segments
3. Step 3a: For Concrete/Brick Installation, Attach the Arms to the Shelf
4. Step 3b: Concrete/Brick InstallationOption
5. Step 4a: For Wood Stud Installation, Attach the Arms to the Shelf
6. Step 4b: Wood Stud Installation Option
7. Step 5: Folding the Shelf

Thank you for choosing Mount It

Read the entire instruction manual before you start installation and assembly. If you have any questions regarding any of the instructions or warnings, please contact
Mount-It! for assistance.

CAUTION : Use with products heavier than the rated weights indicated may result in instability causing possible injury.

• Please closely follow the assembly instructions. Improper installation may result in damage or serious personal injury.
• Safety gear and proper tools must be used. This product should only be installed by professionals.
• This product is designed to be installed on solid concrete walls, masonry walls or wood stud walls.
• Make sure that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.
• Use the mounting screws provided and DO NOT OVER-TIGHTEN mounting screws.
• This product contains small items that could be a choking hazard if swallowed. Keep these items away from children.
• This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.

IMPORTANT: Ensure that you have received all parts according to the component checklist before installation. If any parts are missing or faulty, contact Mount-It! for a replacement.
MAINTENANCE: Check that the product is secure and safe to use at regular intervals (at least every three months).

Mount and Accessories

• Check carefully to make sure there are no missing or defective parts. Some hardware provided may not be used. Use the correct mounting hardware suitable for your installation.
• CHOKING HAZARD. The package includes small parts.
• Not for children under 3 years. Adult supervision is required.
• Missing Parts? Call us at 855-925-5668 and we will ship replacement parts free of charge.

DIMENSIONS & WEIGHT CAPACITY

• Rated weight capacity is 33 lbs for the mount. Caution:
• Ensure all mounting surfaces are capable of holding the weight of your mount.
• DO NOT EXCEED THE MAXIMUM LISTED WEIGHT CAPACITY.
• SERIOUS INJURY OR PROPERTY DAMAGE MAY OCCUR!

INSTALLATION

Step 1 Unfold the Arms

• Unfold the Folding Arm Mounts (#C) until the two ends are fully extended and latch into place at a 90 degree angle.

• Step 2 Connect the Shelf Segments

  • Lay the Left, Middle, and Right Shelves (#A, #B) upside down on a flat surface in the orientation shown here so that Middle Shelf (#B) is in the center.
  • Attach the Shelf Connectors (#D) across the shelf segments as shown using all 32 Bolts (#D) and tighten until secure.
    Note: If a shorter length shelf is desired, the left and right segments can be connected without the middle segment for a 30” wide surface.

• Step 3 Concrete/Brick Installation: Attach the Arms to the Shelf
  Note: Follow this step for Concrete/Brick wall installation. For Wood Stud wall installation proceed to step 4a.
  

  • Place the Folding Arm Mounts (#C) on the bottom of the shelf, centered in the middle of the left and right shelf segments as shown here. Position the back of the mounts to the rear of the shelves, ensuring that the front of the brackets do not extend out over the front edge of the shelf.
  • Once the position is decided secure the Folding Arm Mounts in place using the Screws (#H) through the arms into the shelves, 4 per each arm mount.

• Concrete/Brick Installation Option

  • Hold the shelf to the wall in the desired mounting location and mark the center of the mounting holes with a pencil (6 per arm.)
  • Remove the shelf from the wall. Drill holes in the marked locations using a 5/16” drill bit (8mm) to a depth of 3.3”(85mm). Clear dust or debris from the holes and insert the Concrete Anchors(#G) fully until flush with the wall.
  • Hold the shelf in place over the holes and anchors. Install Lag Screws(#F) through the mount arms and into the concrete anchors then tighten the screws until secure. Do not over tighten.
    Note: Do not drill mounting holes into mortar (such as between bricks or stones) only drill and install into solid stone or concrete surfaces.

• Step 4 Wood Stud Installation: Attach the Arms to the Shelf

  • Using a stud finder locate the studs and mark the edges of each stud with a pencil, then measure the distance between the center of each stud.
  • Place the Folding Arm Mounts (#C) on the bottom of the shelf, so that the distance between the holes on one side only of each arm is equal to the distance between the two studs. Only 3 holes on 1 side of each arm mount will be used, ensure that these are positioned to be the same distance as the center of the studs.
  • Once the position is set, secure the Folding Arm Mounts in place using the Screws (#H) through the arms into the shelves, 4 per each arm mount.

• Wood Stud Installation Option

  • Hold the shelf to the wall in the desired mounting location and mark the center of the mounting holes with a pencil (3 per arm, on one side of each arm only.)
  • Remove the shelf from the wall. Use a 1/8” drill bit and drill on the marked locations to a depth of 3.1”(80mm).
  • Hold the shelf in place over the holes and secure the shelf to the wall using 6x Lag Screws (#F), 3 per arm. Tighten the screws until secure.

• Step 5 Folding the Shelf

  • To fold the shelf down against the wall, squeeze the handles on the underside of each arm up until the latches release, then press the shelf slowly down until it stops.

Visit us at www.mount-it.com for product registration and warranty information.

Our US-based customer service team is standing by to answer any questions you have about your Mount-It! product.
Available by phone Monday – Friday from 8:00 am to 4:00 pm PST.
Chat live with an agent on our website!

SCANNER

Please scan this QR code to visit the product page.

FAQ

Frequently Asked Questions

• Q: What is the weight capacity of the mount?
  • A: The rated weight capacity is 33lbs. Ensure all mounting surfaces are capable of holding this weight to prevent injury or property damage.
• Q: Can children use this product?
  • A: This product contains small parts and is not suitable for children under 3 years. Adult supervision is required.

CONTACT

• support@mount-it.com
• (855)925-5668 OJ
• www.mount-it.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>