MOUNT-IT MI-3880B_G10 Anti Theft Tablet Wall Mount Installation Guide
- June 1, 2024
- Mount-It
Table of Contents
MOUNT-IT MI-3880B_G10 Anti Theft Tablet Wall Mount
Product Information
- Product Name: Mount-It! MI-3772B_G10 / MI-3772W_G10
- Description: Anti-Theft Tablet Wall Mount
Specifications
- Weight Capacity: 2.2 lbs
- Dimensions: 8.9″ x 0.9″ x 13.3″
Product Usage Instructions
Mount and Accessories
Check all parts provided and ensure there are no missing or defective pieces. Use the appropriate mounting hardware for your installation.
Step 1: Open the Tablet Case
Open the tablet case to prepare for installation.
Step 2: Choose the Tablet Adapter
Determine the correct tablet adapter based on the type of tablet you have. Refer to the provided guide for compatibility.
Step 3: Install the Tablet Adapter
Attach the selected tablet adapter to the tablet case securely.
Step 4: Lock the Case
Securely lock the tablet case to ensure the tablet is protected from theft.
Frequently Asked Questions
- Q: What should I do if I have missing parts?
- A: Contact us at 855-925-5668 for free replacement parts.
Thank you for choosing Mount It
Read the entire instruction manual before you start installation and assembly. If you have any questions regarding any of the instructions or warnings, please contact Mount-It! for assistance.
CAUTION: Use with products heavier than the rated weights indicated may result in instability causing possible injury.
- Please closely follow the assembly instructions. Improper installation may result in damage or serious personal injury.
- Safety gear and proper tools must be used. This product should only be installed by professionals.
- This product is designed to be installed on solid concrete walls, masonry walls or wood stud walls.
- Make sure that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.
- Use the mounting screws provided and DO NOT OVER-TIGHTEN mounting screws.
- This product contains small items that could be a choking hazard if swallowed. Keep these items away from children.
- This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.
IMPORTANT: Ensure that you have received all parts according to the component
checklist prior to installation. If any parts are missing or faulty, contact
Mount-It! for a replacement.
MAINTENANCE: Check that the product is secure and safe to use at regular
intervals (at least every three months).
Mount and Accessories
Check carefully to make sure there are no missing or defective parts. Some
hardware provided may not be used. Use the correct mounting hardware suitable
for your installation. CHOKING HAZARD. Package includes small parts.
Not for children under 3 years. Adult supervision is required Missing Parts?
Call us at 855-925-5668 and we will
ship replacement parts free of charge
DIMENSIONS & WEIGHT CAPACITY
Rated weight capacity is 2.2lbs for the mount.
Caution:
Ensure all mounting surfaces are capable of holding the weight of your mount.
DO NOT EXCEED MAXIMUM LISTED WEIGHT CAPACITY. SERIOUS INJURY OR PROPERTY DAMAGE MAY OCCUR!
Installation Instruction
Step 1 Open the Tablet Case
To open the Tablet Case (#A) insert the Key (#I) and turn counterclockwise to
unlock(clockwise to lock).
Step 2a Concrete/Stone Installation Option – 4 Screws
- Using a bubble level to ensure a straight installation, hold the anti-theft case against the wall in the desired location and use a pencil to mark the wall through the 4 bolt holes in the case. Note: This may also be rotated 90° to install in landscape orientation.
- Remove the case from the wall and drill holes in the marked locations using a ¼” (6mm) drill bit to a depth of 1.3” (35mm). Insert Concrete Anchors (#H) into the holes.
- Attach the tablet case to the wall using Lag Screws (#G) and tighten until secure. Do not over tighten.
Note: For a 2 screw installation option, follow the next step using a ¼” drill bit and 1.3” drill depth, and the use of concrete anchors (#H).
Step 2b Wood Stud Installation Option – 2 Screws
- Using a bubble level to ensure a straight installation, hold the anti-theft case against the wall in the desired location and use a pencil to mark the wall through the teardrop shaped bolt hole indicated here, and mark the middle of the horizontal slot below.
- Remove the case from the wall and drill holes in the marked locations using a 7/50” (3.5mm) drill bit to a depth of 1.2” (30mm).
- Install Lag Screw (#G) to the top hole only leaving a gap of approximately ¼” between the wall and thebottom of the screw head.
- Hang the case onto the partially installed screw through the teardrop shaped hole. Slide the case down so that the screw is in the smaller end of the hole, check the level of the case again and install the lower lag screw.
Note: This installation option is compatible with concrete/stone surfaces using the same process but with a¼” drill bit and 1.3” drill depth, and the use of concrete anchors (#H).
Step 3 Select the Tablet Adapter
Select the Tablet Adapter (#B, C, D) for your tablet (see the table below for
compatibility,) and attach it over the tablet inside the case using the 4
Bolts (#F).Replace the front cover onto the Anti-Theft Tablet Case.
Tablet Adapter (#C) can be used with the preinstalled soft button cover to
allow for the tablet home button to be pressed, or it may be removed and
replaced with the hard Button Cover (#E) which will prevent the tablet home
button from being pressed.
Step 4 Lock the Case
Insert the key into the lock and turn the key clockwise to lock the case
Contact
Visit us at www.mount-it.com for product registration and warranty information.
Our US-based customer service team is standing by to answer any questions you have about your Mount-lt! product. Available by phone
- Monday – Friday from 8:00am to 4:00 pm PST.
Chat live with an agent on our website!
Please scan this QR code to visit the product page.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>