MOUNT-IT MI-4222 Deluxe Gaming CPU Mount with Sliding Track Instruction Manual
- June 1, 2024
- Mount-It
Table of Contents
MOUNT-IT MI-4222 Deluxe Gaming CPU Mount with Sliding Track
- Please scan this QR code to visit the product page.
HAVE QUESTIONS?
Monday – Friday from 8:00 am – 4:00 pm PST
Thank you for choosing Mount It!
Read the entire instruction manual before you start installation and assembly. If you have any questions regarding any of the instructions or warnings, please contact Mount-It! for assistance.
Please closely follow the as email instructions. Improper installation may result in damage or serious personal injury.
- Safety gear and proper tools must be used. This product should only be installed by professionals.
- This product is designed to be installed on solid concrete walls, masonry walls or wood stud walls.
- Make sure that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.
- Use the mounting screws provided and DO NOT OVER-TIGHTEN mounting screws.
- This product contains small items that could be a choking hazard if swallowed. Keep these items away from children.
- This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.
IMPORTANT: Ensure that you have received all parts according to the
component checklist before installation. If any parts are missing or faulty,
contact Mount-It! for a replacement.
MAINTENANCE: Check that the product is secure and safe to use at regular
intervals (at least every three months).
Mount and Accessories
- Check carefully to make sure there are no missing or defective parts. Some hardware provided may not be used. Use the correct mounting hardware suitable for your installation.
- CHOKING HAZARD. Package includes small parts. Not for children under 3 years. Adult supervision is required.
- Missing Parts? Call us at 855-925-5668 and we will ship replacement parts free of charge.
DIMENSIONS & WEIGHT CAPACITY
INSTALLATION INSTRUCTION
Step 1
Prepare the Mounting Surface
- Hold the Under Desk Mount (#B) underneath the desk in the desired location. Ensure adequate depth from the edges of the desk to accommodate the dimensions of your PC case. Using a pencil mark the center of the smaller end of the 2 keyhole-shaped screw slots as shown here. Remove the desk mount and drill a hole in the marked location using a 1/8” (3mm) drill bit to a depth of 0.6” (16mm).
Step 2
Attach the Mount
- Partially install 2 Screws (#F) into the drilled locations, leaving a gap of approximately 1/10” (3mm) between the desk and the bottom of the screw head. Place the Under Desk Mount (#B) over the two screws and slide the mount so that the screws are resting in the smaller end of the keyhole slots.
Step 3
Secure the Desk Mount
- Install the remaining 4 Screws (#F) and Washers into the desk. Tighten all 6 screws until secure.
Step 4
Install the Protective Pads
- Apply the Protective Pads (#H) as shown on the CPU Holder (#A) by peeling off the adhesive cover and sticking them to the CPU Holder.
Step 5
Install the Sliders
- Install the Sliders (#D) onto the protruding edges on the top of the CPU holder then slide the CPU Holder into the Under Desk Mount.
Step 6
Attach the End Caps
- Place the End Caps (#C) on each end of the Under Desk Mount and secure them in place with Screws (#E). This will prevent the PC Holder from sliding out of the mount.
Step 7
Insert the PC
- Locate and partially loosen the hand knob on the bottom of the CPU Holder. Expand the lower horizontal arm fully or to a size greater than the width of the CPU. Support the base of the CPU holder with one hand and unlatch the levers on each vertical side of the CPU Holder. Lower the bottom portion to the lowest level.
- Insert the CPU and center it against the vertical column of the CPU Holder. Ensure the fabric pull handle is hanging over the top of the case and is accessible for future use. Lift the bottom of the mount to slide the mount upward until the top of the PC case is touching or close to the top of the of the CPU holder. Pull the latches back down to secure the height setting in place. Press the lower horizontal arm in until it is snug against the side of the CPU case and tighten the hand knob back down.
Visit us at www.mount-it.com for product registration and warranty information.
Our US-based customer service team is standing by to answer any questions you have about your Mount-It! product. Available by phone Monday – Friday from 8:00 am to 4:00 pm PST. Chat live with an agent on our website!
- support@mount-it.com
- (855)925-5668
- www.mount-it.com
Specifications
- Product Model: MI-7172
- Product Name : Deluxe Gaming CPU Mount with Sliding Track
- Weight Capacity : 33lbs
- Top Mounting Bracket Dimensions: 6.2″ x 18.3″ x 6.2″
- Minimum-Maximum Desk Width : 17.3″ – 25.6″
- Minimum-Maximum Desk Depth : 13.4″ – 21.7″
- Minimum-Maximum Desk Thickness : 6″ – 9.7″
Frequently Asked Questions (FAQ)
Q: What should I do if I have missing parts?
A: Call us at 855-925-5668, and we
will ship replacement parts free of charge.
Q: What is the weight capacity of the mount?
A: The rated weight capacity is 33lbs. Do not exceed this limit to prevent
injury or damage.
Q: Is this product safe for children?
A: The product contains small parts and is not suitable for children under 3
years. Adult supervision is required.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>