MOUNT-IT MI-1765LT Monitor Mount with Wall Mount Plate Instruction Manual

May 15, 2024
Mount-It

MOUNT-IT MI-1765LT Monitor Mount with Wall Mount Plate Instruction Manual
MOUNT-IT MI-1765LT Monitor Mount with Wall Mount Plate

Thank you for choosing Mount-It

Read the entire instruction manual before you start installation and assembly. If you have any questions regarding any of the instructions or warnings, please contact Mount-t for assistance

CAUTION: Use with products heavier than the rated weights indicated may result in instability causing possible injury.

  • Please closely follow the assembly instructions. Improper installation may result in damage or serious personal injury.
  • Safety gear and proper tools must be used. This product should only be installed by professionals.
  • This product is designed to be installed on solid concrete walls, masonry walls or wood stud walls.
  • Make sure that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.
  • Use the mounting screws provided and DO NOT OVER TIGHTEN mounting screws
  • This product.contains small items that could be a choking hazard if swallowed. Keep these items away from children.
  • This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.

IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installation. If any parts are missing or faulty, contact Mount-!! for a replacement.

MAINTENANCE: Check that the product is secure and safe to use at regular intervals (at least every three months).

Mount and Accessories

  • Spring Arm

  • Wall Mount Plate

  • Decorative Cover

  • 3 mm Hex Wrench

  • Laptop Tray

  • 5 mm Hex Wrench

  • Pole Clamp

  • M8x65 Alternate Bolt

  • Laptop Clamp

  • Clamp Connectors

  • M4x12

  • M5x12

  • D5

  • ST6.3×55 Lag Screw/

  • 010×45 Concrete Anchor

  • D6

Check carefully to make sure there are no missing or defective parts. Some hardware provided may not
be used. Use the correct mounting hardware suitable for your installation.

CHOKING HAZARD. Package includes small parts.
Not for children under 3 years. Adult supervision is required.

Missing   Parts? Call us at 855-925-5668 and we will ship replacement parts free of charge.

DIMENSIONS & WEIGHT CAPACITY

DIMENSIONS

Rated weight capacity is 4.4lbs~15.4lbs for the mount.

Caution:

Ensure all mounting surfaces are capable of holding the weight of your mount.
DO NOT EXCEED MAXIMUM LISTED WEIGHT CAPACITY.
SERIOUS INJURY OR PROPERTY DAMAGE MAY OCCUR!\\

Step 1

Step 1a-1

A. Wood Stud Mounting Option

Mounting Option

  • With a stud finder locate the stud and center the Wall Mount Plate (#B) on the stud at the desired height.
  • Using a bubble level to ensure straightness mark the center of the mounting holes with a pencil.
  • Use a 3/16” drill bit and drill on the marked locations to a depth of 2.2”. Secure the Wall Mount Plate (#B) to the wall using Lag Screws (#W-A) and Washers (#W-C). Tighten the screws until secure.

Concrete/Brick Mounting Option

Mounting Option

  • Using a bubble level to ensure straightness hold the Wall Mount Plate (#B) to the desired location on the wall and mark the center of the mounting holes with a pencil.
  • Use a 3/8” drill bit and drill on the marked locations to a depth of 2.4”. Clear any dust and debris from
    the holes and insert the Concrete Anchors (#W-B). Secure the Wall Mount Plate (#B) to the wall using Lag Screws (#W-A) and Washers (#W-C). Tighten the screws until secure.

Step 1a-2

Insert Decorative Covers

Insert Decorative Covers

Insert the Decorative Covers (#C) into each of the bolt holes.

Step 1b

Pole Clamp Mounting Option

Attaching the Pole Clamp (Pole Diameters Between 1.1″-1.8″)

  • Using Hex Wrench (#E) loosen the two bolts on the Pole Clamp (#F) until the clamp opens wide enough to slide onto the pole.
  • Move the Clamp to the desired height and tighten the bolts back down until secure.
    Installation

Attaching the Pole Clamp (Pole Diameters Between 1.8″-2.4″)

  • Using Hex Wrench (#E) remove the two bolts from the Pole Clamp (#F) and replace them with the
    Alternate Bolts (#G). After installing the alternate bolts, adjust the width of the clamp to be slightly larger than the pole.

  • Move the Clamp to the desired height and tighten the bolts back down until secure.’ Installation

Step 2

Attach the Spring Arm to the Mount

Installation

WARNING
STORED ENERGY

  • The monitor arm is shipped compressed and under tension
  • When cutting the cable tie firmly hold and brace both parts using your hands as shown or ask for the assistance of another person.
  • Failure to follow this process may result in personal injury or property damage.
  • Place the end of the Spring Arm (#A) onto the end of the Wall Mount or Pole Mount. Tighten the bolt on the back of the Spring Arm to secure the arm to the mount.
    InstallationInstallation

Step 3

Step 3a-1

Attach the Clamps to the Laptop Tray

  • Attach the Laptop Clamps (#I) to the Laptop Tray (#H) using Clamp Connectors (#J) as shown here.
    One end of the Clamp Connectors will pass through the outer slot on the Laptop Tray, while the other
    end will pass over the outer edge of the tray. Clip the Clamp Connectors into place on the Clamps to secure them to the Tray.
    Installation

Step 3a-2

Attach the Laptop Tray to the Spring Arm

  • Attach the Laptop Tray (#H) to the top 4 bolt holes on the Spring Arm (#A) using Bolts (#M-A) and Washers (#M-C).
    Installation

Step 3a-3

Insert the Laptop

  1. Flip the tab on the Laptop Clamps up to release the sliding arms.
  2. Flip the small arms on the front of the Laptop Tray up so that they are perpendicular to the laptop surface.
  3. Place the laptop on the tray, slide the Clamp arms in until they are snug against the side of the laptop, and press the tabs back down to secure the arms in place. Cables can be run through the cable management clips on the underside of the spring arm.
    Installation
    Installation

Step 3b-1

Optional Monitor Instructions: Install the Top Bolts to the Monitor

  • Select the appropriate size mounting bolt (#M-A, M-B)for your display’s mounting holes and verify the length of the VESA bolt is not too long. If you are unsure of the correct bolt size for your display refer to your user manual or contact the monitor manufacturer for sizing information.
  • After selecting the appropriate bolt install the top two bolts and washers (#M-C) to the monitor leaving a gap of approximately 0.1” (3mm).
    Installation

Step 3b-2

Attaching the Monitor

  • Hang the monitor onto the top of the VESA plate as shown.
  • Install the lower two bolts and washers (#M-C) through the lower holes. Tighten all 4 bolts until secure, do not over tighten.
    Installation

Step 4

Final Adjustments

  • Cables can be run through the cable management clips on the underside of the spring arm.
    Final Adjustments

  • CAUTION: This monitor mount utilizes a mechanical spring assembly that does not require tension adjustments to balance the weight of the monitor. Do not loosen the spring cover bolts. Removing the cover will detach the spring and it will be unable to be reattached. Any adjustment to these parts will cause irreversible damage to the monitor arm.

  • The viewing angle can be adjusted in the range of -45° to +90°, and the screen can be rotated 360°. Each joint can swivel left or right for alternate viewing angles.

  • Note: Adjust to the desired angle then tighten the screws using the tool as shown, alternating from each screw as you tighten them.

  • Installation

Visit us at www.mount-it.com for product registration and warranty information.

Our US based customer service team is standing by to answer any questions you have about your Mount-It! product.

Available by phone Monday – Friday from 8:00am to 4:00pm PST.

Chat live with an agent on our website!

support@mount-it.com

855-925-5668

www.mount-it.com

Company Logo

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Mount-It User Manuals

Related Manuals