MOUNT-IT MI-4222 Heavy Duty Under Desk Wall CPU Mount Instruction Manual

: June 1, 2024
: Mount-It

Table of Contents

MOUNT-IT MI-4222 Heavy Duty Under Desk Wall CPU Mount
Product Information
Product Usage Instructions
FAQs
INTRODUCTION
Mount and Accessories
Mounting Hardware
DIMENSIONS
INSTALLATION STEPS
Read User Manual Online (PDF format)
Download This Manual (PDF format)

MOUNT-IT MI-4222 Heavy Duty Under Desk Wall CPU Mount

MOUNT-IT-MI-4222-Heavy-Duty-Under-Desk-Wall-CPU-Mount-
product

Product Information

Specifications
- Model: MI-7171
- Type: Heavy-Duty Under Desk / Wall CPU Mount
- Weight Capacity: 44lbs
- Dimensions:
- Min: 5.9 x 4.5 x 0.9 inches
- Max: 16.9 x 5.6 x 3.9 inches

Product Usage Instructions

Step 1: Install the Protective Pads
- Ensure all mounting surfaces are clean and dry.
- Remove the backing from the protective pads.
- Place the protective pads on the areas where the mount will make contact with the desk or wall.
Step 2: Attach the Horizontal Arm
- Secure the horizontal arm to the main mount body using the provided screws and washers.
- Tighten the screws with the hex wrench to ensure a secure connection.
Step 3: Widen the Mount
- Adjust the mount to fit the width of your CPU by following the specific instructions provided in the manual.
Step 4a: Attach the Mount
- Position the mount under the desk or against the wall in the desired location.
- Secure the mount using the appropriate mounting hardware provided.
Step 4b: Optional Installation Method – Solid Wood Wall/Desk
- Follow additional instructions provided in the manual for installation on solid wood surfaces.
Step 4c: Optional Installation Method – Stone/Concrete Wall
- Follow additional instructions provided in the manual for installation on stone or concrete surfaces.
Step 5: Insert the PC
- Carefully slide the CPU into the mount ensuring it is securely held in place.
- Double-check all connections and ensure stability before use.

FAQs

Q: What should I do if I have missing parts?
- A: Contact us at 855-925-5668, and we will ship replacement parts free of charge.
Q: What is the weight capacity of the mount?
- A: The rated weight capacity is 44 lbs. Do not exceed this limit to prevent injury or property damage.

INTRODUCTION

Thank you for choosing Mount It!
Read the entire instruction manual before you start installation and assembly. If you have any questions regarding any of the instructions or warnings, please contact Mount-It! for assistance.
CAUTION: Use with products heavier than the rated weights indicated may result in instability causing possible injury.

Please closely follow the assembly instructions. Improper installation may result in damage or serious personal injury.
Safety gear and proper tools must be used. This product should only be installed by professionals.
This product is designed to be installed on solid concrete walls, masonry walls or wood stud walls.
Make sure that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.
Use the mounting screws provided and DO NOT OVER TIGHTEN mounting screws.
This product contains small items that could be a choking hazard if swallowed. Keep these items away from children.
IMPORTANT: Ensure that fou have leived a parts according oute compone it checkis prit ai installation. any parts are missing or faulty, contact Mount I!
MAINTENANCE: Check that the product is secure and safe to use at regular intervals (at least every three months).

Mount and Accessories

$MOUNT-IT-MI-4222-Heavy-Duty-Under-Desk-Wall-CPU-Mount-fig-1 $1$$

Mounting Hardware

$MOUNT-IT-MI-4222-Heavy-Duty-Under-Desk-Wall-CPU-Mount-fig-1 $2$$

Check carefully to make sure there are no missing or defective parts. Some hardware provided may not be used.
Use the correct mounting hardware suitable for your installation.
CHOKING HAZARD. Package includes small parts.
Not for children under 3 years. Adult supervision is required.
Missing Parts? Call us at 855-925-5668 and we will ship replacement parts free of charge.

DIMENSIONS

DIMENSIONS & WEIGHT CAPACITY

$MOUNT-IT-MI-4222-Heavy-Duty-Under-Desk-Wall-CPU-Mount-fig-1 $3$$

INSTALLATION STEPS

Step 1 Install the Protective Pads
- Apply the Protective Pads #C) as shown by peeling off the adhesive cover and sticking them to the interior of the Horizontal Arm (#B). $MOUNT-IT-MI-4222-Heavy-Duty-Under-Desk-Wall-CPU-Mount-fig-1 $4$$
Step 2 Attach the Horizontal Arm
- Attach the Horizontal Arm (#B) to the Mount Body (#A) using Bolts (#D) and Washers (#E). $MOUNT-IT-MI-4222-Heavy-Duty-Under-Desk-Wall-CPU-Mount-fig-1 $5$$
Step 3 Widen the Mount
- Widen the mount to a size larger than that of your PC by loosening the bolts shown here on the horizontal arm, and the lower side support. To extend the length of the mount, pull and hold the ring on the back of the mount, slide the mount to the appropriate length and release the ring. Check that it has latched in place by trying to slide the two ends apart.
1. Loosen the bolt on the horizontal arm to adjust the length of the arm.
2. Loosen the 2 screws on the side of the base to adjust the width of the base.
3. Pull and hold the ring on the back of the mount to raise and lower the mount. Note: support the base with one hand if the PC is inserted to prevent it from lowering too quickly. $MOUNT-IT-MI-4222-Heavy-Duty-Under-Desk-Wall-CPU-Mount-fig-1 $6$$
Step 4a Attach the Mount
- Required Desk Thickness 0.6* (15mm) minimum.
- Hold the Mount underneath the desk in the desired location. Ensure adequate depth from the edges of the desk to accommodate the dimensions of your PC case. Using a pencil mark the center of all 4 screw holes making sure to mark the smaller end of the 2 keyhole-shaped screw slots as shown here. Remove the desk mount and drill holes in the marked locations using a 1/8″ (3mm) drill bit to a depth of 0.4″ (10mm).
- Partially install the 2 Screws #F) that correspond to the keyhole slots, which will be on opposite corners. Leave a gap of approximately 0.2″ (4mm) between the desk and the bottom of the screw head.
- Place the mount over the two screws and slide the mount so that the screws are resting on the smaller end of the keyhole slots.
- Install the remaining 2 screws and tighten all 4 down until secure. $MOUNT-IT-MI-4222-Heavy-Duty-Under-Desk-Wall-CPU-Mount-fig-1 $7$$
Step 4b Optional Installation Method: Solid Wood Wall/Desk
- Hold the Mount against the solid wood surface in the desired location and use a bubble level to check straightness. Using a pencil mark the center of all 4 screw holes making sure to mark the smaller end of the 2 keyhole shaped screw slots as shown here. Remove the mount and drill holes in the marked locations using a 1/8″ (3mm) drill bit to a depth of 1.5* (38mm).
- Partially install the 2 Screws #G) that correspond to the keyhole slots, which will be on opposite corners. Leave a gap of approximately 0.2″ (4mm) between the wall and the bottom of the screw head.
- Place the mount over the two screws and slide the mount down so that the screws are resting in the smaller end of the keyhole slots.
- Install the remaining 2 screws and tighten all 4 down until secure.
Step 4c Optional Installation Method: Stone/Concrete Wall
- Hold the Mount against the concrete surface in the desired location and use a bubble level to check straightness. Using a pencil mark the centre of all 4 screw holes making sure to mark the smaller end ofthe 2 keyhole-shaped screw slots as shown here. Remove the mount and drill holes in the marked locations using a 1/4″ (6mm) drill bit to a depth of 1.5″ (38mm). Insert Concrete Anchors (#H) into the holes.
- Partially install the 2 Screws #G) that correspond to the keyhole slots, which will be on opposite corners. Leave a gap of approximately 0.2″ (4mm) between the wall and the bottom of the screw head. Place the mount over the two screws and slide the mount down so that the screws are resting in the smaller end of the keyhole slots.
- Install the remaining 2 screws and tighten all 4 down until secure.
Step 5 Insert the PC
- Insert the PC and slide the arms back in until snug against the side of the case, then tighten the bolts back in place.
- If needed shorten the length of the mount pulling the ring on the back of the mount, raise or lower the mount to the appropriate length and release the ring while supporting the bottom of the mount allowing it to latch into place.

Visit us at www.mount-it.com for product registration and warranty information.

Our US-based customer service team is standing by to answer any questions you have about your Mount-It! product.
Available by phone Monday – Friday from 8:00 am to 4:00 pm PST.
Chat live with an agent on our website!

HEAVY-DUTY UNDER-DESK / WALL CPU MOUNT