MOUNT-It MI-4222 Heavy Duty Tilt TV Wall Mount Instruction Manual
- May 15, 2024
- Mount-It
Table of Contents
MOUNT-It MI-4222 Heavy Duty Tilt TV Wall Mount
Product Specifications
- Model : MI-1377
- Type : Heavy-Duty Tilt TV Wall Mount
- Weight Capacity : 165lbs
- Dimensions : 17.6″ x 3.2″ x 24.6″
- Tilt Range : 7.9″ to 15.7″
- Compatible TV Sizes : 24″ to 60″
Product Usage Instructions
Mount and Accessories
Check the package contents to ensure all parts are included and not defective.
Installation Options
Step 1a: Wood Stud Installation Option
Step 1b: Concrete/Brick Installation Option
Attaching VESA Brackets to the TV
Follow the instructions to securely attach the VESA brackets to your TV.
Optional Tilt Adjustment Knobs
Adjust the tilt of the mount using the provided knobs for optimal viewing angles.
Hang the TV on the Wall Mount
Securely hang your TV on the wall mount following the provided guidelines.
FAQ
- Q: What is the weight capacity of the MI-1377 wall mount?
- A : The rated weight capacity is 165lbs.
- Q: What are the dimensions of the wall mount?
- A : The dimensions are 17.6″ (height) x 3.2″ (depth) x 24.6″ (width).
- Q: How do I adjust the tilt of the TV once it’s mounted?
- A : You can adjust the tilt using the optional adjustment knobs provided with the mount.
Thank you for choosing Mount It
Read the entire instruction manual before you start installation and assembly.
If you have any questions regarding any of the instructions or warnings,
please contact
Mount-It! for assistance.
- Safety gear and proper tools must be used. This product should only be installed by professionals.
- This product is designed to be installed on solid concrete walls, masonry walls, or wood stud walls.
- Make sure that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.
- Use the mounting screws provided and DO NOT OVER-TIGHTEN mounting screws.
- This product contains small items that could be a choking hazard if swallowed. Keep these items away from children.
- This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.
- IMPORTANT : Ensure that you have received all parts according to the component checklist prior to installation. If any parts are missing or faulty, contact Mount-It! for a replacement.
- MAINTENANCE. Check that the product is secure and can be sold at regular intervals (at least every three months)
Mount and Accessories
TV Mounting Hardware
Wall Mounting Hardware
Check carefully to make sure there are no missing or defective parts. Some hardware provided may not be used. Use the correct mounting hardware suitable for your installation.
CHOKING HAZARD. The package includes small parts.
Not for children under 3 years. Adult supervision is required.
Missing Parts?
Call us at 855-925-5668 and we will ship replacement parts free of charge.
DIMENSIONS & WEIGHT CAPACITY
The rated weight capacity is 165 lbs for the mount.
Caution: Ensure all mounting surfaces are capable of holding the weight
of your mount.
DO NOT EXCEED THE MAXIMUM LISTED WEIGHT CAPACITY. SERIOUS INJURY OR PROPERTY
DAMAGE MAY OCCUR!
Step 1a
Wood Stud Installation Option
- Use a stud finder to locate the center of the studs and hold the Wall Mount(#C) to the wall in the desired mounting location.
- Place the Bubble Level #E) centered on the top of the Wall Mount #C) and ensure that the mount is level.
- Mark the center of the studs through the mount as shown.
- Remove the Mount from the wall and drill holes in the marked locations using a 3/16″ drill bit (4.5mm) to a depth of 2.2″ (55mm).
- Hold the Wall Mount (#C) to the wall over the holes, check the level once again, and install the 4 Lag Screws (#W-A) and Washers (#W-C) then tighten until secure.
Step 1b
Concrete/Brick Installation Option
- Hold the Wall Mount#C to the wall in the desired mounting location.
- Place the Bubble Level #E) centered on the top of the Wall Mount (#C) and ensure that the mount is level.
- Mark the center of the holes through the mount in the locations shown.
- Remove the Mount from the wall and drill holes in the 6 marked locations using a 3/8″ drill bit (10mm) to a depth of 2.4″ (60mm).
- Clear dust or debris from the holes and insert the Concrete Anchors (#W-B) fully until flush with the wall. Hold the Wall Mount (#C) to the wall over the holes, check the level once again, and install the 6 Lag Screws (#W-A) and Washers (#W-C) then tighten until secure.
- Note : Do not drill mounting holes into the mortar (such as between bricks or stones) only drill and install into solid stone or concrete surfaces.
Step 2
Optional Tilt Adjustment Knobs
- The mount tilt can be adjusted with the nut indicated here, on VESA Brackets (#A, #B). For easier adjustment, the nut can be removed and replaced with the Tilt Adjustment Knobs (#D).
- Note : The original nut may be left in place if installed in locations where the viewer should not be able to adjust the tilt, such as public or customer-facing installations.
Step 3
Attaching the VESA Brackets to the TV
- This mount is intended for use in the portrait orientation, so ensure that the orientation of your TV and VESA brackets match the Illustration.
- Select the appropriate size mounting bolt (Select one size #M-A, M-B, M-C, or M-D) and washer (M-E) for your display’s mounting holes and verify the length of the VESA bolt is not too long. If you are unsure of the correct bolt size for your display refer to your display’s user manual or contact the display’s manufacturer or sizing information. i necessary, use te Included spacers wir. M-o, between te mount and the screen as shown above to adjust the length of the mounting bolt. Multiple spacers can be used in combination to achieve tne desired bon depth.
- Attach the Right and Left VESA Brackets (#A, B) to the TV as shown using the selected bolts. Ensure unat the dit ad ustment knobs (or nut on me side orte vesA brackets are Racine toward me curse edges of the TV or you will be unable to properly adjust the tilt of the screen.
Step 4
Hang the TV on the Wall Mount
- It is recommended that you use the assistance of a second person for this step. Hang the TV on the wall mount as shown so that the top of the VESA brackets hook onto the top of the wall mount, then lower the bottom of the tv carefully until the mount latches into place.
- To adjust the tilt angle of the screen, loosen the tilt adjustment knobs or nuts, adjust the screen to the desired viewing angle, then tighten them back down.
- The mount may be secured in place by attaching a lock (not included) through the holes shown here, while the mount is latched into place on the wall mount.
- To remove the TV from the wall mount, pull down on the pull cords to release the latches, pull the base of the TV away from the wall, and then lift the TV up and off the wall mount.
Visit us at www.mount-it.com for product registration and warranty information.
Our US-based customer service team is standing by to answer any questions you
have about your Mount-It! product.
Available by phone Monday – Friday from 8:00am to 4:00 pm PST.
Chat live with an agent on our website!
Please scan this QR code to visit the product page.
HAVE QUESTIONS?
Monday – Friday from 8:00 am – 4:00 pm PST
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>